Alfred14

Is this not a limitation for the bedrock edition?

Alright, so I'm currently running a vanilla server with about 8-10 players and the server is lagging a bit (140ish ticks behind). It seems to be pegging one thread at a time, alternating between different threads. Is there a way to spread the load across more cores? Or is minecraft heavily limited to a single thread? (running a E3-1245 v5)

Thanks for that, so just for my knowledge, why are you also adding the three host keys?

Hi @Capt.Insano just wonder if you could help me a little setting this up, I'm assuming you mean i need to map this information to somewhere in the local AppData directory? Do i add four path variables routing those things to the appdata directory and then add two port variables?

I am also trying to share a USB printer over the network, i tick on sharing within the admin panel but cant find the printer in the network, is there any special commands we need to be running to get this working?

Thanks Johnnie, unfortunately my drives are on a backplane so i have tried moving the drive into another slot and to see if the errors still keep happening.

Hi, I have 38,066 errors on this disk WDC_WD30EFRX-68EUZN0_WD-WCC4N4FCUY6F I have attached a full diagnostics report and wondering if someone can tell me whats going wrong? I have completed a parity check and it seems to have come back ok, as in i am still seeing a green ball unraid Diagnostics 100717.zip

Hi all, After having a catastrophic failure of my main unraid server losing all my data i am looking to try and prevent this from happening again so i am going to set up another server to 'mirror' the main one and am asking what the best method for doing this would be? Ideally i would be able to issue a Wake on LAN command to get the backup server running transfer the new changes and then shutdown when finished so i can save power, anyone know the best way to achieve this?

The photos still show for me in 2 different browsers? Not sure whats going on. Also Squid i have now done what you suggested and every single slot works, so the worst thing is now i have no idea why all of my hard drives were fried. I did change the cables so not sure if that could have had an effect?

Bump, does anyone know if there is a way i cant test if the backplanes are functioning correctly?

I eliminated that as a problem because I everything connected and there was no burn out when disconnecting the 2 extra SSD's.

I'm hoping i can get a bit of help/guidance on what went wrong and potential avenues for a fix. I purchased a norco RPC-3216 case and outfitted it with 6 drives and to cache drives using unraid, i was using a 650 watt Thermaltake power supply and everything ran smoothly for a number of months but then looking back on it i did something pretty dumb. The case has a total of 8 molex connectors for 16 drives and originally i only plugged 4 in but was having issues with 2 slots along one of the rows so i just assumed it was a power issue so i went out and bought some molex to sata adaptors and 2 new SSD’s to expand my cache array, I then hot plugged all these connections and when i did that the whole server died and when i tried to re-boot it something was shorting out and i lost my motherboard. I tried the drives in another computer and they all seemed to be ok, so didnt lose any data that time, a week or so later i found out that you only need to use 4 molex plugs and not 8 so i bought a 2nd hand motherboard to test and this time only using 4 molex plugs but with all 4 SSD’s hooked up again the HDD backplane started smoking so i immediately tried taking away the 2 new SSD’s and i got no smoking problems at all but unfortunately at this stage i had lost all my drives due to the PCB’s burning out. The thing i can't explain is why the 2 extra ssd’s were causing the short? Is it because i was pulling too many amps from the 5 volt rail?

I have an IBM M1015 card, i don't think there is any other option to flash it to IT mode?\ I tried stopping the array unassigning the drive, restarting the array, stopping the array re-assigning the drive and the starting the array but i still didn't like the disk so i just performed a data rebuild on a disk i had spare and everything seems to be working now. I must admit those errors are annoying me, obviously they are not consistent with other people who are using IBM M1015 cards.

attached diagnostics tower-diagnostics-20160630-2141.zip

I can post diagnostics, if there is nothing wrong with the drive how do I get it to come back online?

Could someone tell me what is wrong with this disk? ST3000DM001-1ER166_Z501QERG-20160630-1619.txt

Ok thanks for all your help Trurl but i ended up putting a new disk in the place of the one that was reporting as wrong and UNraid seemed to rebuild the data on that disk but when the process was complete about 8 hours later it now says that disk is unmountable and i need to format it? What could be the issue here?

Ok, so have managed to get all my disks back in the array but now one of the disks, i'm guessing it was the one i performed a repair on, it now will not let me start the array and instead says "The replacement disk must be as big or bigger than the original." What steps can i follow to get my array back online?

Ok no worries thanks for your help!

ok yep i'm following now, another question, would it be possible to take one drive offline and re-build the data that was on it into the rest of the array? So in a way downsizing the array

Yep, this has been a good lesson, i suppose i just never would assume that something would randomly go wrong with my icybox backplane that would cause 2 drives to go offline.

If any drive was altered by the other system in any way you have invalidated parity. Ok, is there a special why i need to follow to re-create parity or will the system recognize the problem and fix it?

Sorry only one drive had a bad superblock the other was fine

What if the repair actually did nothing and said that the file system was intact?

I did run xfs_repair on another system and that seemed to fix the drive as i could access all the data, but yes later after some more diagnosis it seems it was/is a connection issue in my icybox 5 in 3 bay, not sure what is going on but seems like the backplane is causing issues on 3 of the 5 drive bays.