Duniac

Hi All, Thanks for your suggestions, but problem has been resolved. When checking the settings in Sonarr > General section. I noticed that the host name was entered as http://<Server_IP>. Once I changed this to just the <Server_IP>, communication resumed and I was able to successfully test the Indexer and Downloader.

Sonarr not connecting to Indexer or Downloader when using Proxy Yesterday I configured Sonarr and SABnzbd, all went well and I was able to configure a couple of shows and started grabbing some missing episodes. Today, I watched Spaceinvader One's video on configuring Privoxy. Since doing so, Sonarr will not connect to the Indexers or Downloaders. Testing the connections, they fail, if I turn off 'Use Proxy' in Sonarr, they connect. I'm obviously missing something here, can someone please assist.

Hi All, Couple of updates: 1. I have purchased a new drive to try to recover data. 2. I completed a firmware update on the disk which originally caused the problems. Now, when I applied the firmware update on the disk, Seagate advises to backup the disk as it may result in lost data. itimpi: I have ran a full scan of the disk which was experiencing the problems (took about 15 hours), no errors were found. tee-tee jorge: The errors I experienced were prior to extracting the disk to update the firmware. I haven't had time

Looks like things are going from bad to worse. I've now lost disk 1 (Unmountable: No file system). Backing up data seems to be a lost cause at the moment as nothing is copying, everything is showing read errors. I do have backups of critical data, but I hope not to have to loose everything, but it seems like that is what is happening now. Still don't understand why these problems has suddenly appeared, but will try to move forward...

It does seem odd that I have been operating without problems for about six months. Should I look at replacing the Controller or will the firmware update be sufficient? Will also be performing the following: Purchasing another drive to ensure dual parity Running diagnostics on the disk causing the problems Updating firmware on all disks Extracting the controller card and updating the firmware Reinstalling controller card and disk Will preclear new disk and the disk causing the problems. Insert new disk into the array in the pos

How should I approach fixing the read errors occuring?

Update: followed the instructions https://wiki.unraid.net/UnRAID_Manual_-_FAQ The drive was identified correctly, added to the array and the parity rebuild began. However, the error re-appeared, see new diagnostics. Ran SMART extended self-test, however the following message appeared - Interrupted (host reset). Also noticed that all of my docker containers have gone missing. Also, also seems that this drive is not being emulated at all, as I am missing a lot of content. I will be purchasing a new drive in about one week, but in the meantime I'll be running wi

Thanks for the suggestions, will look at updating the firmware on the HBA controller and HDD. Hopefully this will correct the problem. In the meantime I have suspended all operations and turned off all containers, I don't want any operation occurring while I have two bad disks.

Hi All, I have been using Unraid for a couple of couple of months now, and have 1 parity drive with 5 drives in the storage array (would like to configure a second parity disk soon). This week disk 3 became disabled with errors in the logs (blk_update_request: i/o error). I researched the error and tried connecting the disk to another channel on the hba controller, no change. After changing the channel, I removed the disk from the array and ran pre-clear, the error appeared in the pre-read, I then ran pre-clear again and it completed successfully. Then ran pre-clear

For previous Plex dockers I have spread it across all disks, should I limit it to only one disk?

Many have written that they have backed up their Plex database, can someone please point me to the location of this?

I have just updated to 6.8 RC5 and am in the process of reinstalling the Plex docker. I've read that RC5 includes the fix, but are there any specific config items I need to set?

Ok, this is odd. It seems to be working today!

I installed Community Applications, which is the only plugin installed. However, I can only view two of the applications contained within the plugin.

Hi All, I new to Unraid and I've downloaded 6.4.1, but this plugin pack doesn't seem to be complatible with it, should I try 6.4.0?