digitalfixer

Which version of system profiler are you using (see plugins tab) ? 2015.6.27. Kevin.

I hope this is the right place for this. Unraid 6.1rc2 There is bug in the system profiler plugin. Memory is reported wrong. (see pic) This was also present in Unraid 6.0.1 Kevin [Edit] I also tried it in Safari. Cleared cache. No change. Chrome and Safari on iPad are the same.

SirG Would you be able to add the sftp module to this please. Kevin.

Will look into it for future versions Why is this needed? What is wrong with automatic detection? If you run lsscsi what do you get? Just hedging your bets with autodetection. but as for the WD Red 4Gs lssci: smartctl Note the emphasis and: I found that adding this line to my go file stopped all problem with a drive not being in the smartctl database /usr/sbin/update-smart-drivedb Kevin.

No, didn't see that one, thanks for pointing out. Can you telnet into your system and post the result of the command: dmidecode -q -t memory Interesting root@Tower:~# dmidecode -q -t memory Memory Device Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM_A1 Bank Locator: BANK 0 Type: Unknown Type Detail: None Speed: Unknown Manufacturer: [Empty] Serial Number: [Empty] Asset Tag: 9876543210 Part Number: [Empty] Rank: Unknown Configured Clock Speed: Unknown Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Single-bit ECC Maximum Capacity: 32 GB Number Of Devices: 4 Memory Device Total Width: 72 bits Data Width: 64 bits Size: 8192 MB Form Factor: DIMM Set: None Locator: DIMM_A2 Bank Locator: BANK 1 Type: DDR3 Type Detail: Synchronous Speed: 1600 MHz Manufacturer: Micron Serial Number: E8A36F46 Asset Tag: 9876543210 Part Number: 18JSF1G72AZ-1G6E1 Rank: 2 Configured Clock Speed: 1600 MHz Memory Device Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM_B1 Bank Locator: BANK 2 Type: Unknown Type Detail: None Speed: Unknown Manufacturer: [Empty] Serial Number: [Empty] Asset Tag: 9876543210 Part Number: [Empty] Rank: Unknown Configured Clock Speed: Unknown Memory Device Total Width: 72 bits Data Width: 64 bits Size: 8192 MB Form Factor: DIMM Set: None Locator: DIMM_B2 Bank Locator: BANK 3 Type: DDR3 Type Detail: Synchronous Speed: 1600 MHz Manufacturer: Micron Serial Number: E8A36E23 Asset Tag: 9876543210 Part Number: 18JSF1G72AZ-1G6E1 Rank: 2 Configured Clock Speed: 1600 MHz root@Tower:~# Kevin. I have made an update to the system info plugin. Use the plugin manager to upgrade to the latest version 2015.02.01 Thanks for sharing the information and enable me to make a correction. That sorted that problem. Thank you. Kevin.

No, didn't see that one, thanks for pointing out. Can you telnet into your system and post the result of the command: dmidecode -q -t memory Interesting root@Tower:~# dmidecode -q -t memory Memory Device Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM_A1 Bank Locator: BANK 0 Type: Unknown Type Detail: None Speed: Unknown Manufacturer: [Empty] Serial Number: [Empty] Asset Tag: 9876543210 Part Number: [Empty] Rank: Unknown Configured Clock Speed: Unknown Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Single-bit ECC Maximum Capacity: 32 GB Number Of Devices: 4 Memory Device Total Width: 72 bits Data Width: 64 bits Size: 8192 MB Form Factor: DIMM Set: None Locator: DIMM_A2 Bank Locator: BANK 1 Type: DDR3 Type Detail: Synchronous Speed: 1600 MHz Manufacturer: Micron Serial Number: E8A36F46 Asset Tag: 9876543210 Part Number: 18JSF1G72AZ-1G6E1 Rank: 2 Configured Clock Speed: 1600 MHz Memory Device Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM_B1 Bank Locator: BANK 2 Type: Unknown Type Detail: None Speed: Unknown Manufacturer: [Empty] Serial Number: [Empty] Asset Tag: 9876543210 Part Number: [Empty] Rank: Unknown Configured Clock Speed: Unknown Memory Device Total Width: 72 bits Data Width: 64 bits Size: 8192 MB Form Factor: DIMM Set: None Locator: DIMM_B2 Bank Locator: BANK 3 Type: DDR3 Type Detail: Synchronous Speed: 1600 MHz Manufacturer: Micron Serial Number: E8A36E23 Asset Tag: 9876543210 Part Number: 18JSF1G72AZ-1G6E1 Rank: 2 Configured Clock Speed: 1600 MHz root@Tower:~# Kevin.

bonieni I don't if you saw this error that is in the System Info plugin. http://lime-technology.com/forum/index.php?topic=36633.msg340429 Kevin

Tried with the array running and clean boot with array stopped. I'm going to leave it now until after boxing day then have a good look at my bios settings for usb related stuff and install a 2 port pci-e usb card. Hopefully something will work so I can get the bluray drive working on my kvm. I'll follow up with anything I find. Kevin.

archedraft That was the first chunk in my code list. root@Tower:~# lspci|grep USB 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 05) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 05) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 05) Kevin.

I've followed the guide and the results make no sense in that every socket is coming back as bus 003. The Lexar is the usb stick I used to move around. If I plug it back in a port I've already listed the Device number goes up by 1 [Edit] This was done with the array running and clean boot, array stopped. The results were the same. Kevin. p9d-m usb ports root@Tower:~# lspci|grep USB 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 05) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 05) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 05) root@Tower:~# lsusb Bus 002 Device 002: ID 8087:8000 Intel Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:8008 Intel Corp. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 003: ID 0781:5571 SanDisk Corp. Cruzer Fit internal socket Bus 003 Device 007: ID 046b:ff31 American Megatrends, Inc. Bus 003 Device 006: ID 046b:ff40 American Megatrends, Inc. Bus 003 Device 005: ID 046b:ff20 American Megatrends, Inc. Bus 003 Device 004: ID 046b:ff10 American Megatrends, Inc. Virtual Keyboard and Mouse Bus 003 Device 002: ID 046b:ff01 American Megatrends, Inc. Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@Tower:~# lsusb Bus 003 Device 003: ID 0781:5571 SanDisk Corp. Cruzer Fit Bus 003 Device 008: ID 05dc:a440 Lexar Media, Inc. JumpDrive Lightning front usb2 left root@Tower:~# lsusb Bus 003 Device 003: ID 0781:5571 SanDisk Corp. Cruzer Fit Bus 003 Device 009: ID 05dc:a440 Lexar Media, Inc. JumpDrive Lightning front usb2 right root@Tower:~# lsusb Bus 003 Device 003: ID 0781:5571 SanDisk Corp. Cruzer Fit Bus 003 Device 010: ID 05dc:a440 Lexar Media, Inc. JumpDrive Lightning front usb3 (single socket) root@Tower:~# lsusb Bus 003 Device 003: ID 0781:5571 SanDisk Corp. Cruzer Fit Bus 003 Device 011: ID 05dc:a440 Lexar Media, Inc. JumpDrive Lightning rear usb2 bottom root@Tower:~# lsusb Bus 003 Device 013: ID 05dc:a440 Lexar Media, Inc. JumpDrive Lightning rear usb2 top Bus 003 Device 003: ID 0781:5571 SanDisk Corp. Cruzer Fit root@Tower:~# lsusb Bus 003 Device 003: ID 0781:5571 SanDisk Corp. Cruzer Fit Bus 003 Device 014: ID 05dc:a440 Lexar Media, Inc. JumpDrive Lightning rear usb3 bottom root@Tower:~# lsusb Bus 003 Device 003: ID 0781:5571 SanDisk Corp. Cruzer Fit Bus 003 Device 015: ID 05dc:a440 Lexar Media, Inc. JumpDrive Lightning rear usb3 top root@Tower:~# ls root@Tower:~# readlink /sys/bus/usb/devices/usb1 ../../../devices/pci0000:00/0000:00:1a.0/usb1 root@Tower:~# readlink /sys/bus/usb/devices/usb2 ../../../devices/pci0000:00/0000:00:1d.0/usb2 root@Tower:~# readlink /sys/bus/usb/devices/usb3 ../../../devices/pci0000:00/0000:00:14.0/usb3 root@Tower:~# readlink /sys/bus/usb/devices/usb4 ../../../devices/pci0000:00/0000:00:14.0/usb4 root@Tower:~#

If I remember the way I fixed it was to remove the S3 plugin via the webgui and delete dynamix.cfg. Then I rebooted and in settings select Display Settings and clicked Apply. Reinstalled the S3 Sleep plugin and all was fine after that. My initial error was that no Sleep button ever displayed but that fixed it. Also this line does not appear in my dynamix.cfg. [confirm]\nsleep="1"\n Kevin.

It works fine for me. More information on how it breaks would be useful then I'm sure someone will have an answer. Kevin.

Updated S3 sleep plugin. Still no sleep button on Array Operation. dynamix.cfg [display] date="%c" number=".," scale="-1" align="right" tabs="0" text="0" view="" total="1" spin="1" usage="0" icons="1" banner="" theme="white" unit="C" hot="45" max="55" poll="0" refresh="1000" sysinfo="/Tools/SystemProfiler" [confirm]\nsleep="1"\n Kevin.

Bonienl I modified the dynamix.cfg file and added the key. The sleep button is now displayed. Kevin.

I just disabled page refresh and now the file looks normal again. Kevin.

dynamix.cfg now looks like this. sleep="1" [sleep] sleep="1" [display] sleep="1" date="%c" sleep="1" number=",." sleep="1" scale="-1" sleep="1" align="right" sleep="1" tabs="0" sleep="1" text="0" sleep="1" view="" sleep="1" total="1" sleep="1" spin="1" sleep="1" usage="1" sleep="1" icons="1" sleep="1" banner="" sleep="1" theme="white" sleep="1" unit="C" sleep="1" hot="45" sleep="1" max="55" sleep="1" poll="0" sleep="1" refresh="60000" Kevin.

I tried this. Nothing about sleep appears under Display settings. Kevin. Before uninstall/install did you save display settings ? Yes. Kevin.

Can you try the following: 1. Goto Settings -> Display Settings and press Apply (this saves settings to the flash memory) 2. Uninstall and re-install S3.sleep plugin, after installation, it should add a "sleep" key to the file created in step 1 3. Sleep button should now be visible I now have sleep="1" in the config file but no button on the display. Kevin.

bonienl No. The plugins I have installed all have their own dir. Kevin.

I've installed the new S3 sleep plugin but no sleep button is shown on the Array Operation tab. Kevin