trurl Posted September 2, 2022 Share Posted September 2, 2022 Many of your disks are very full. Full disk may not perform as well, and you need to keep some free space in case you need to repair filesystem Quote Link to comment
trurl Posted September 2, 2022 Share Posted September 2, 2022 On 8/26/2022 at 4:35 PM, SLNetworks said: Drive #7 is physically removed, not sure why it sits there On 8/28/2022 at 7:06 PM, trurl said: If you don't want it in the array you will have to New Config without it and rebuild parity. Did you take care of this? Until you do you effectively only have single parity since you already have a missing disk. Quote Link to comment
trurl Posted September 2, 2022 Share Posted September 2, 2022 11:00.0 SATA controller [0106]: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller [1b4b:9172] (rev 11) Subsystem: ASRock Incorporation 88SE9172 SATA 6Gb/s Controller [1849:9172] Marvell NOT recommended but if it isn't causing any problems don't worry about it. Quote Link to comment
SLNetworks Posted September 5, 2022 Author Share Posted September 5, 2022 I used it to attach my cache drives and a ninth Exos drive. I would rather not, but it was the first server I built.. and I've learned what I'm not doing next time. LOL I'm just happy it's working out as I was pretty low on storage before adding it, and swapping other drives. Never building a 2U server again. Quote Link to comment
SLNetworks Posted September 12, 2022 Author Share Posted September 12, 2022 On 9/2/2022 at 3:48 PM, trurl said: Did you take care of this? Until you do you effectively only have single parity since you already have a missing disk. So, I've tried removing it.. and tried moving Disk 8 to slot 7. Unraid claims it becomes an invalid configuration, and I can't switch from 10 slots to 9. Quote Link to comment
trurl Posted September 12, 2022 Share Posted September 12, 2022 https://wiki.unraid.net/Manual/Tools#New_Config Quote Link to comment
SLNetworks Posted September 12, 2022 Author Share Posted September 12, 2022 Done Quote Link to comment
trurl Posted September 13, 2022 Share Posted September 13, 2022 2 hours ago, SLNetworks said: Done It hasn't had time to rebuild 16TB parity. Is it doing that now? Quote Link to comment
SLNetworks Posted September 17, 2022 Author Share Posted September 17, 2022 My twin 16s have been updated for parity since re-doing the drive array setup. No mess ups.. but it doesn't auto-start after a parity check, but runs fine otherwise. Would it be worth upgrading to 6.11.0-rc5? Quote Link to comment
trurl Posted September 17, 2022 Share Posted September 17, 2022 4 minutes ago, SLNetworks said: doesn't auto-start after a parity check Don't know what you mean. Parity check can't be run unless array is started. Quote Link to comment
SLNetworks Posted September 18, 2022 Author Share Posted September 18, 2022 The array stopped after the parity check completed yesterday. Had a power outage and it had wanted to check parity. I just took note of how odd it was that it had stopped the array after it finished. Quote Link to comment
trurl Posted September 18, 2022 Share Posted September 18, 2022 38 minutes ago, SLNetworks said: Had a power outage and it had wanted to check parity. I just took note of how odd it was that it had stopped the array after it finished. You should get an UPS. Are you saying you had an unclean shutdown parity check, and then it stopped the array by itself after the parity check completed? Quote Link to comment
SLNetworks Posted September 28, 2022 Author Share Posted September 28, 2022 (edited) Note the array autostart disabled. I just rebooted to update to v6.11 Edited September 28, 2022 by SLNetworks Added info Quote Link to comment
trurl Posted September 28, 2022 Share Posted September 28, 2022 So you don't mean it stopped by itself, you just mean it didn't autostart? Post new diagnostics Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.