shagz Posted March 9, 2020 Share Posted March 9, 2020 Hello omicron-diagnostics-20200308-1751.zipg Unraid 6.8.2 Had an 8tb Drive Fail , was going to replace disk #8 (sdk) with the same size in my array ( picture attached ) Having issues trying to format the drive . (I have destructive mode enabled in Unassigned devices plus ) Drive simply fails to format after typing "Yes" in the field ( also drive hasn't been fully pre-cleared yet ) To add to this my log quickly fills up to 100 % with fix common problems error coming up ( pic also attached ) Not sure if these are related or mutually exclusive as ive had a good run for a while and now things are starting to go south . Would like to re-build the array but this has me stuck . I have changed the physical SATA cable 1nce on the affected drive My searches span from possible SATA controller to power supply to just about anything down a rabbit hole Your expertise is appreciated . Logs are attached - Thanks in advance ! omicron-diagnostics-20200229-1256.zip Quote Link to comment
dlandon Posted March 9, 2020 Share Posted March 9, 2020 53 minutes ago, shagz said: Drive simply fails to format after typing "Yes" in the field ( also drive hasn't been fully pre-cleared yet ) That's not possible because UD+ is not installed: statistics.sender.plg - 2017.09.22 unassigned.devices.plg - 2020.02.09 unbalance.plg - v2019.10.26 unRAIDServer.plg - 6.8.2 You are having disk issues. This is only a sample of the log: Feb 29 02:42:36 OMICRON kernel: ata10: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Feb 29 02:42:36 OMICRON kernel: ata10.00: link online but device misclassified Feb 29 02:42:40 OMICRON kernel: ata10.00: failed to IDENTIFY (I/O error, err_mask=0x100) Feb 29 02:42:40 OMICRON kernel: ata10.00: revalidation failed (errno=-5) Feb 29 02:42:40 OMICRON kernel: ata10.00: disabled Feb 29 02:42:41 OMICRON kernel: ata10: hard resetting link Feb 29 02:42:51 OMICRON kernel: ata10: softreset failed (1st FIS failed) Feb 29 02:42:51 OMICRON kernel: ata10: hard resetting link Feb 29 02:43:01 OMICRON kernel: ata10: softreset failed (1st FIS failed) Feb 29 02:43:01 OMICRON kernel: ata10: hard resetting link Feb 29 02:43:36 OMICRON kernel: ata10: softreset failed (1st FIS failed) Feb 29 02:43:36 OMICRON kernel: ata10: limiting SATA link speed to 3.0 Gbps Feb 29 02:43:36 OMICRON kernel: ata10: hard resetting link Feb 29 02:43:42 OMICRON kernel: ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 320) Feb 29 02:43:42 OMICRON kernel: ata10.00: link online but device misclassified Feb 29 02:43:42 OMICRON kernel: ata10: link online but 1 devices misclassified, device detection might fail Feb 29 02:43:42 OMICRON kernel: sd 10:0:0:0: [sdk] tag#6 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 Feb 29 02:43:42 OMICRON kernel: sd 10:0:0:0: [sdk] tag#6 Sense Key : 0x5 [current] Feb 29 02:43:42 OMICRON kernel: sd 10:0:0:0: [sdk] tag#6 ASC=0x21 ASCQ=0x4 Feb 29 02:43:42 OMICRON kernel: sd 10:0:0:0: [sdk] tag#6 CDB: opcode=0x88 88 00 00 00 00 01 36 aa 01 b8 00 00 01 00 00 00 Feb 29 02:43:42 OMICRON kernel: print_req_error: I/O error, dev sdk, sector 5212078520 Feb 29 02:43:42 OMICRON kernel: md: disk8 read error, sector=5212078456 Feb 29 02:43:42 OMICRON kernel: md: disk8 read error, sector=5212078464 Feb 29 02:43:42 OMICRON kernel: md: disk8 read error, sector=5212078472 Feb 29 02:43:42 OMICRON kernel: md: disk8 read error, sector=5212078480 Recommendations: Solve the disk issues before you do anything else to the array. You'll make it worse. Check cabling and disk controller. Update your plugins. You are way behind. Quote Link to comment
dlandon Posted March 9, 2020 Share Posted March 9, 2020 Your disks are also running pretty hot. Quote Link to comment
shagz Posted March 11, 2020 Author Share Posted March 11, 2020 (edited) Thanks for the insight I have purchased a new SATA controller and new SATA cord to the affected drive UD+ was installed and run at a later date than the 1st two logs , plugins updated as suggested Still at the same crossroads trying to get the WDC tb drive to format to rebuild parity . @dlandon two new logs have been added . Any suggestions ? omicron-diagnostics-20200311-1634.zip omicron-diagnostics-20200311-1914.zip omicron-smart-20200311-1909.zip Edited March 11, 2020 by shagz name Quote Link to comment
trurl Posted March 12, 2020 Share Posted March 12, 2020 1 hour ago, shagz said: trying to get the WDC tb drive to format to rebuild parity Parity does not have a filesystem so there is no point in formatting it. Looks like it's still having problems communicating with that disk. Quote Link to comment
shagz Posted March 12, 2020 Author Share Posted March 12, 2020 Any recommendations as to the next step ? Quote Link to comment
JorgeB Posted March 12, 2020 Share Posted March 12, 2020 Errors start as soon as the disk is initialized, could be a connection problem (replace/swap) cables or it could be the controller, Marvell controllers are not recommended for Unraid. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.