cadamwil Posted October 2, 2020 Share Posted October 2, 2020 Hello, recent convert from FreeNAS. In FreeNAS, every morning, I got a SMART report that showed a synopsis of the info polled from the drives. I liked to see it to see if my drives were getting hot due to lack of airflow or similar. An example of the synopsis from the top is seen below. +------+------------------+----+-----+-----+-----+-------+-------+--------+------+----------+------+-------+----+ |Device|Serial |Temp|Power|Start|Spin |ReAlloc|Current|Offline |Seek |Total |High |Command|Last| | |Number | |On |Stop |Retry|Sectors|Pending|Uncorrec|Errors|Seeks |Fly |Timeout|Test| | | | |Hours|Count|Count| |Sectors|Sectors | | |Writes|Count |Age | +------+------------------+----+-----+-----+-----+-------+-------+--------+------+----------+------+-------+----+ |da0 ? |WD-WCC7K1EX1CS8 | 30 |24448| 30| 0| 0| 0| 0| N/A| N/A| N/A| N/A| 4| |da1 ? |WD-WCC4E1809741 | 33 |45431| 90| 0| 0| 0| 0| N/A| N/A| N/A| N/A| 633| |da2 |BTPR321300PV040AGN| |43622| 0| | 0| | | N/A| N/A| N/A| N/A| 0| |da9 |ZL287G90 | 27 | 10| 1| 0| 0| 0| 0| 0| 1131| N/A| 0| 0| |ada0 ?|S418NF0K942377M | 30 |13421| | | 0| | | N/A| N/A| N/A| N/A| 559| |ada1 ?|S418NF0K942370W | 29 |13421| | | 0| | | N/A| N/A| N/A| N/A| 559| |da3 ? |WD-WCC4E1804946 | 34 |45431| 90| 0| 0| 0| 0| N/A| N/A| N/A| N/A| 633| |da4 ? |WD-WCC4E1800859 | 31 |45430| 90| 0| 0| 0| 0| N/A| N/A| N/A| N/A| 633| |da5 ? |WD-WCC4E1809854 | 31 |45434| 93| 0| 0| 0| 0| N/A| N/A| N/A| N/A| 633| |da6 ? |WD-WCC4E1809961 | 32 |45434| 93| 0| 0| 0| 0| N/A| N/A| N/A| N/A| 633| |da7 ? |WD-WCC7K7NYJZ9C | 33 |24459| 30| 0| 0| 0| 0| N/A| N/A| N/A| N/A| 4| |da8 ? |WD-WCC7K0KFEELT | 30 |24339| 30| 0| 0| 0| 0| N/A| N/A| N/A| N/A| 4| |da10 |ZL2867P7 | 27 | 10| 1| 0| 0| 0| 0| 0| 1107| N/A| 0| 0| +------+------------------+----+-----+-----+-----+-------+-------+--------+------+----------+------+-------+----+ Further, I would also get a scrub report after scrubs were run, just to give me the statistics. Would anyone have recommendations for how I can do this in Unraid, is there a plugin or docker? FYI, I am using ZFS in unraid as well. I have scrubs setup in cron, but I would like reports, preferably emailed to me. Quote Link to comment
Squid Posted October 2, 2020 Share Posted October 2, 2020 Unraid will send you a daily status report (basically array good or not good) if you set it up. For SMART however the monitored attributes (Settings Disk Settings, with overrides also per disk) are sent out on as as needed basis (checked every minute). Personally, I'd much prefer when something goes wrong rather than a daily report on SMART which IF something goes wrong, or is beginning to go wrong that notification gets lost in a sea of emails saying Please disperse, Nothing to see here. For graphs etc, look at the scrutiny app, but it only graphs once per day. Alternatively, the project Ultimate Unraid Dashboard may also do what you want. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.