wow001

Is there any way to adjust column width in the Shares tab as the name column is not wide enough to show the full name of a folder being shared?

Thank you. Repairing the USB key worked and all backup and working.

Unsure which of the following changes I did since last reboot that may have caused my unraid to stall when booting. I have updated the system to 6.10 RC5, Updated Dynamix File Manager to the latest version and swapped to two drives in the hot swap bays when the server was shut down. Both drives where mounted as unassigned devices and where not part of the array. After swapping the drives between the different bays I was unable to start the unraid server. Looking at the boot up screen it looks more look the USB key with the unraid system problem? The server boots into the Uriad System then stalls at the second attached image. Does any body have suggestions where to start trouble shooting this problem? I have swapped the USB key to another slot and my motherboard Asrock X570D4U-2L2T only has USB 3 ports.

The https://jc-lan.org/2020/01/09/crossflash-dell-0wfn6r-9341-8i-to-9300-8i-it-mode/ is now password protected so use this link below instead. This method worked for me but needed the jumper on TP12 as the LSI card came from a Dell T7910 so running the command " sas3flash.efi -list " got the message "No Adaptor found" , so after restating the computer with the jumper on the HBA I was able to replace the firmware with the SAS9300_8i_IT.bin As I could not run the -list command I photographed the serial number and SAS Address for later when need later in the method. https://www.servethehome.com/flash-lsi-sas-3008-hba-e-g-ibm-m1215-mode/ Also the link for the installer_P16_for_UEFI.zip - uefi boot and flashing tool 9300_8i_Package_P16_IR_IT_FW_BIOS_for_MSDOS_Windows.zip - firmware etc. https://www.broadcom.com/site-search?q=installer_P16_for_UEFI https://www.broadcom.com/site-search?q=9300_8i_Package_P16_IR_IT_FW_BIOS_for_MSDOS_Windows

Thank you, that explains it.

Unsure if I ever had the icon but I have upgraded from 6.9.2 to 6.10.0-rc2, changed my usb boot device and a forced restart that was not Unraid related. Is there a way to get the icon back or what is the easiest way to reinstall 6.10.0-rc2 to the usb stick and keep my configuration?

Donate you 2 beers for the help and the syncthing docker

Thank you binhex Yes I was using /mnt/user/sg projects as the folder path in the Syncthing web interface (webpage) So installing the docker again (just in case) and leaving all the docker setting at they default. Create a new folder in the Syncthing web interface using /media/sg projects and the syncing work with all my user shares! Thanks again.

I am stumped at the same point: 2022-03-05 22:56:33: Failed to create folder root directory mkdir /mnt/user: permission denied 2022-03-05 22:56:33: Error on folder "sg projects" (xseqs-rkkhk): folder path missing I am running unraid 6.10.0-rc2 and under tools I do not have Docker Safe Perms icon - should it be there? Also the folder I am trying to sync is one of my samba shares. The Docker is a new install and the config is the default setup. But any samba share folder has the same error: 2022-03-05 22:56:33: Failed to create folder root directory mkdir /mnt/user: permission denied 2022-03-05 22:56:33: Error on folder "sg projects" (xseqs-rkkhk): folder path missing What am I missing?