rud

Hello, I'm seeking guidance for the installation of Adguard-Home on my Unraid server. I've configured it with the br0 network and assigned a static IP address (192.168.1.27). I checked to make sure that address is not being used by anything on my local network. I'm unable to access the WebUI. The container seems to be running fine. Here are the logs: 2024/09/26 09:08:19.136232 [info] AdGuard Home, version v0.107.52 2024/09/26 09:08:19.136259 [info] This is the first time AdGuard Home is launched 2024/09/26 09:08:19.136263 [info] Checking if AdGuard Home has necessary permissions 2024/09/26 09:08:19.136344 [info] AdGuard Home can bind to port 53 2024/09/26 09:08:19.136836 [info] safesearch default: disabled 2024/09/26 09:08:19.136950 [info] Initializing auth module: /opt/adguardhome/work/data/sessions.db 2024/09/26 09:08:19.136974 [info] auth: initialized. users:0 sessions:0 2024/09/26 09:08:19.136977 [info] AdGuard Home updates are disabled 2024/09/26 09:08:19.136978 [info] web: initializing 2024/09/26 09:08:19.136983 [info] This is the first launch of AdGuard Home, redirecting everything to /install.html 2024/09/26 09:08:19.136993 [info] AdGuard Home is available at the following addresses: 2024/09/26 09:08:19.137058 [info] go to http://127.0.0.1:3000 2024/09/26 09:08:19.137060 [info] go to http://192.168.1.27:3000 So, it seems to have launched and installed correctly? Not sure if it's relevant, but I use Tailscale for remote access to my server. Not sure if that's messing with anything. I've tried removing the port from the web address to access the WebUI as recommended through another post on here, however the WebUI still does not load. I've also tried accessing the WebUI through different browsers, still no go. I'd like to use a custom network to have AdGuard Home have its own IP address on my local network. Any guidance or advice is greatly appreciated. Thank you for your time.

I went ahead and added that. I also went into the BIOS and made sure ASPM was off. Once again, thank you for the help and quick replies!

Firstly, thank you so much for the quick reply. I went ahead and power cycled the server. Was able to run another scrub and this time it was able to correct the errors. Ran another one and it seems good now. Although it seems fixed now, should I be concerned with the NVME device dropping offline? Is there more investigating I should do or be cautious about? ** Update** - Unfortunately, I was browsing through the webui, and now it seems the Docker Service failed to start. I assume my Docker file got corrupted since the drive went offline, so I went ahead and recreated the Docker image. Everything okay seems on *that* end now, but my question about concerns over the NVME device d ropping offline (long term) still stands. Thank you! Thanks again

Hello, I set up my cache pool for errors using the steps outlined in this post a while ago because I had problems with Docker not starting. The docker image was corrupt and needed to be recreated. I went ahead and did that and things have been fine. Unfortunately, I woke up this morning to more errors on my cache pool. Tried running a scrub (and then a scrub with repair corrupted blocks) but unfortunately lots were uncorrectable: Running btrfs dev stats /mnt/cache twice (with about a few minutes between running the command): Tried running Fix Common Errors, but nothing. Is nvme0n1p1 failing? If so, what steps should I take? I have them ran as a mirror. Attaching diagnostics and would appreciate any help. Thank you! noumenon-diagnostics-20231221-0604.zip

Okay, just making sure. Thank you so much!

So, I followed the directions you outlined, and it reported some read write errors with my 1st nvme cache drive. I created a user script as outlined as well, as well as forced a reset of the stats. Then I ran a scrub and it was able to repair the errors : I also set up a scrub schedule as I was finishing up. About 1hr later, I got a notification (as set up from the user script) that there were errors on the cache pool again. I ran the same commands and had this: I followed the same steps and performed another scrub, but this time it reported no errors were found / none needed correction: Am I okay? Or do you think there may be another underlying issue? Thanks for your help once again.

Done and done. Thank you. Also, apologies for creating another post - I thought I had posted to the wrong section and I tried to delete it, but clearly didn't. My bad!

Hello, Been on 6.12.4 for a little over a week now with no problems, but noticed today my Docker tab said, "Docker Service failed to start". It doesn't have any errors on the docker tab Settings > Docker Attaching diagnostics. Haven't had any drive errors or warnings under notifications. Would appreciate any help. Thanks in advance! noumenon-diagnostics-20231207-1814.zip

Hello, Been on 6.12.4 for a little over a week now with no problems, but noticed today my Docker tab said, "Docker Service failed to start". It doesn't have any errors on the docker tab Settings > Docker Attaching diagnostics. Would appreciate any help. Thanks in advance! noumenon-diagnostics-20231207-1814.zip

Hello, apologies if this is posted to the wrong section. I wasn't sure if this belonged in the feature request area or in the support section because I wasn't sure if this is possible in 6.12+ but I just haven't turned it on correctly. I came from 6.11 and found the counter notification layout extremely useful as opposed to the bell (in 6.12+). Is there a way to change notifications to the old counter layout? Thanks!

Hello, Just installed on 6.12.4 and I'm having the same issue as iceperson above. The servers animation just spins and clicking on the Get Plex Token button doesn't do anything. I tried a different browser as well. Clicking on Save or Remove Token also loads a blank page. Also tried removing the plugin, restarting unraid, re-installing but no change. Thanks for the help.