luisv

I was able to figure it out. I noticed an error in the docker log with server IP and port listed twice, so I went back to the Plex tab and I mistakenly entered the port number along with the Plex server's IP address... I'm just used to typing in the port # so did it out of habit. Once I removed the port number, and tried it again, it ran successfully and the email was sent. It took another min or two to update the web page.

Very nice... I like what I see. Kudos for sure! I ran the test report, but no email yet... any logs other than the docker log so I can look for errors?

In the docker log it said I had to visit http://hostServerIP:hostPort/admin to run the wizzard. Running it now.

If you have the previous version installed, you'll need to give it another port as well. When I did that, it simply opened the web page... no wizard to complete the install.

Is there a post that highlights the differences between the two versions or what's new?

Thanks @johnnie.black

Thanks for all the help!

Restore is complete, sorry for the silly question as this is the first time I've had to do this, but how do I get my dockers an VMs back? Both tabs are blank.

Yes, I didn't exclude any directories and the vdisks were on the cache.

Just dockers and VMs, I have a backup from this past Sunday. I guess it's just quicker to format and restore? Then update the dockers as a few had updates since the weekend.

Sorry, I replied on the other thread, this is basically a duplicate thread. I can delete this one if necessary. davault-diagnostics-20180316-0327.zip

I added two data drives to my system as well as an LSI 9211-8i controller. I moved my 2 cache drives to make space for the two data drives, but I kept the cache drives connected to the same SATA ports on the motherboard. When I booted up the system, one of the cache drives was recognized, but the second was not. It shows as Unmountable: No Files System. Not sure what to do next as the only option I see below, is to format the drive. I have a backup of the Appdata folder from this past Sunday. Any help is appreciated.

Worked perfectly, thanks!

A few days ago I replaced a 4TB Parity disk with a 6TB disk and everything went smoothly. Now I would like to add that 4TB disk to the array, add another 6TB HGST as well as a SATA optical drive to the system. Since I'm out of SATA ports on my motherboard, I purchase an LSI 9211-8i; however, before I dive in I have a couple of questions: To make things easy, I was thinking of keeping the current 8 disks connected to the motherboard and connect the two disks along with the optical drive to the LSI 9211-8i. Any performance issues in splitting the data disks in this fashion? The optical drive is currently connected via USB in an external case, so I figured why not mount it internally as I have the room and extra SATA ports. I assume since unRAID recognizes the optical drive via USB, it shouldn't have an issue connected via SATA. When I swapped out the parity disk I labeled the disks for future identification purposes. In doing so, I noticed that the order the disks within the UI are not the order that they are mounted within the case. Although it doesn't truly matter, I'm curious if I can move them around so they are ordered properly as per the UI. My disks are mounted on drive sleds, so I figured I could simply disconnect the SATA and power cables from the disks and reposition them within the case to match the UI. This is probably an unnecessary step, but figured if it's not a issue moving them around, why not take another 10 - 15mins to rearrange them.

Any thoughts on what I should do? Migrated without an issue and Tautulli runs perfectly, but should I delete/ remove the PleyPy docker? I ask as the migration instructions said to use the existing PlexPy appdata folder for /config, so I assume if I remove PlexPy it would delete that PlexPay appdata folder and break Tautilli.

Upgraded and so far so good.

Just completed... took 12 hours, 11 minutes, 31 seconds with an average speed of 136.7 MB/sec.

Thanks! Parity sync / data rebuild underway.

Great, very easy process to migrate. Should I leave the PlexPy docker in place, but not running or can it be removed?

I would like to replace my current 4TB parity drive with a 6TB drive; however, I don't have any available SATA ports for the new disk. I believe I can do the following; however, can someone confirm as this is the first time I'm going through this process. Perform parity check Shutdown server Remove current parity drive and connect the new one Turn system back on System will indicate an error in that the parity disk is not connected, so I assign the new 6TB drive as the parity drive Start the array and allow it to rebuild parity At a later date I will be installing an LSI controller card so I will add the older 4TB parity drive back to the array as a data disk. At that time, I assume I can follow the normal process of adding a data disk... clearing and formatting it... there isn't a different process since it used to be a parity disk?

Folders? Where do you set that?

I'm thinking about moving media files between libraries and remove a couple of libraries; however, I don't want NowShowing to think the media files that have been moved are considered new content and therefore send out a notification. Is there a way this can be done?

Awesome! I for one appreciate everyone's time and efforts! Maybe I'm oversimplifying things, but what are the next steps to get the updated plugin within CA.

+1 on a separate tab.

Just saw the info for this docker via Twitter... very cool and simple. Can you pass multiple webapp URLs in a txt file to import? Made it my browser's homepage.