Inimical

Can't seem to get this to sync between unraid and an android phone - everything seems to be running and connected, however it just stays at "syncing" and doesn't transfer anything? Any ideas?

If I'm understanding correctly this would only work for Unifi branded cameras - what about 3rd party like Hikvision?

Has anyone had success adding camera to the Unifi Video NVR? For whatever reason it's not detecting any of my cameras.

I've recently upgraded my internet connection to Gig speed, I regularly download at about 80-90MB's. Seems SAB can't handle this and it slows my entire unRAID server to a crawl. Is there a way to resolve this and still maintain the speeds? Should I be looking for an alternative to SAB? Thanks.

Restart of the server or restart of the container? Restart the server - restarting the container is what causes the server to hang.

Every couple of months SAB stops responding - trying to restart it hangs unraid, only option seems to be a restart of the server. Anyone else experience anything like this?

Works great, thanks!

Haven't used torrents in years.. Are there any private trackers someone can recommend? I tried PB, but seems to picking up mostly junk.

Any reason to choose one or the other between this and Deluge?

Well, I was right, it did get buggered up... Glad you got it sorted, that's a lot easier fix than if the symlinking was knackered. Wow, I didn't even see your reply when I posted that. Thanks anyways.

Ran new perms on the cache drive, and it seems to be working now.

I just swapped out my cache drive, which required backing up the Plex application directory to the array, and then moving it back. Upon starting Plex from the new cache drive I get the below error in the log. Plex starts, but does not fully load. Any ideas? Mar 24 09:32:00 Tower dbus[42]: [system] org.freedesktop.DBus.Error.AccessDenied: Failed to set fd limit to 65536: Operation not permitted

Using http://www.canyouseeme.org No! However, I CAN connect to the service! I AM connected to the service. Thanks, I'll keep at it.

I can't see any obvious issues that would cause the test to fail. I have just tested both my main and redundant instances of this plugin though and both mine fail too. However, I have been using them all morning. I am even using one of them now. Have you tried to just connect anyway? The test says that: Perhaps the reason it fails has something to do with the fact it is running in a Container on a Server on a different Subnet with just ports forwarded to the connectivity ports. I don't know. I wouldn't worry - if it works - all is good! Give it a try! Doesn't seem to work. If you test your configured port externally does it show as open?

Make a backup copy of the needo plex appdata (shouldn't need it) and then point this plex to the same plex appdata. Thank you.

.

Can't seem to get a successfull connectivity test externally or internally. Configured UDP port forwarding on the router on 1194. Any ideas?

Apologies if this was already asked here, but how do I go from Needo's container to this one without losing data?

Any issue if I install this over a previous config? (Different container)

Running Minimux using this container.. Can anyone explain how to configure password? Read through the thread, still not sure I understand.

Anyone able to get this method to upgrade to version 6?

Thanks

How does this look? ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Raw_Read_Error_Rate = 118 100 6 ok 176700400 Spin_Retry_Count = 100 100 97 near_thresh 0 End-to-End_Error = 100 100 99 near_thresh 0 High_Fly_Writes = 7 100 0 near_thresh 93 Airflow_Temperature_Cel = 66 70 45 near_thresh 34 Temperature_Celsius = 34 30 0 ok 34 No SMART attributes are FAILING_NOW Thanks! preclear_start__Z300S3DM_2013-10-01.txt preclear_rpt__Z300S3DM_2013-10-01.txt preclear_finish__Z300S3DM_2013-10-01.txt