mattcrem

Members
  • Posts

    15
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

mattcrem's Achievements

Noob

Noob (1/14)

0

Reputation

  1. Does anyone know if STV-AV1 encoding can be added to the container?
  2. The problem is I have two failed drives, I have replaced one of them with a fresh new drive (as I'm out of SATA ports) and unraid tells me that there are too many bad drives and the array won't start at all. is there any way around this?
  3. So I ran the below: ~# smartctl -d ata -tlong /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org Read SMART Data failed: Input/output error it just shows the I/O error in less than 1 minute of entering the command
  4. smartctl -a -d ata /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST2000DM001-1CH164 Serial Number: Z340CGBC LU WWN Device Id: 5 000c50 064b34a34 Firmware Version: CC27 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue May 18 13:57:19 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled Read SMART Data failed: Input/output error === START OF READ SMART DATA SECTION === Error SMART Status command failed: Input/output error SMART Status command failed: Input/output error SMART overall-health self-assessment test result: UNKNOWN! SMART Status, Attributes and Thresholds cannot be read. SMART Error Log Version: 1 ATA Error Count: 554 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 554 occurred at disk power-on lifetime: 35743 hours (1489 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 ff ff ff 4f 00 03:37:23.810 READ FPDMA QUEUED 61 00 00 ff ff ff 4f 00 03:37:23.809 WRITE FPDMA QUEUED 60 00 f8 48 02 00 40 00 03:37:23.407 READ FPDMA QUEUED 60 00 f8 48 01 00 40 00 03:37:23.406 READ FPDMA QUEUED 60 00 78 c8 00 00 40 00 03:37:23.406 READ FPDMA QUEUED Error 553 occurred at disk power-on lifetime: 35742 hours (1489 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 78 ff ff ff 4f 00 03:15:15.182 READ FPDMA QUEUED 60 00 40 ff ff ff 4f 00 03:15:15.182 READ FPDMA QUEUED 61 00 38 ff ff ff 4f 00 03:15:15.181 WRITE FPDMA QUEUED 61 00 40 ff ff ff 4f 00 03:15:15.094 WRITE FPDMA QUEUED 61 00 30 ff ff ff 4f 00 03:15:15.082 WRITE FPDMA QUEUED Error 552 occurred at disk power-on lifetime: 35742 hours (1489 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 a8 ff ff ff 4f 00 03:15:11.427 WRITE FPDMA QUEUED 60 00 38 ff ff ff 4f 00 03:15:11.422 READ FPDMA QUEUED 60 00 d0 ff ff ff 4f 00 03:15:11.422 READ FPDMA QUEUED 61 00 40 ff ff ff 4f 00 03:15:11.420 WRITE FPDMA QUEUED 61 00 38 ff ff ff 4f 00 03:15:11.418 WRITE FPDMA QUEUED Error 551 occurred at disk power-on lifetime: 35742 hours (1489 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 20 ff ff ff 4f 00 03:15:07.023 WRITE FPDMA QUEUED 60 00 60 ff ff ff 4f 00 03:15:07.005 READ FPDMA QUEUED 60 00 40 ff ff ff 4f 00 03:15:07.005 READ FPDMA QUEUED 60 00 98 ff ff ff 4f 00 03:15:07.004 READ FPDMA QUEUED 61 00 60 ff ff ff 4f 00 03:15:07.003 WRITE FPDMA QUEUED Error 550 occurred at disk power-on lifetime: 35742 hours (1489 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 88 ff ff ff 4f 00 03:15:03.238 READ FPDMA QUEUED 61 00 88 ff ff ff 4f 00 03:15:03.236 WRITE FPDMA QUEUED 60 00 a8 ff ff ff 4f 00 03:15:03.167 READ FPDMA QUEUED 60 00 58 ff ff ff 4f 00 03:15:03.167 READ FPDMA QUEUED 60 00 48 ff ff ff 4f 00 03:15:03.166 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 31226 - # 2 Short offline Completed without error 00% 17784 - # 3 Short offline Completed without error 00% 17643 - # 4 Short offline Completed without error 00% 17502 - # 5 Short offline Completed without error 00% 17361 - # 6 Short offline Completed without error 00% 17256 - # 7 Short offline Completed without error 00% 17115 - # 8 Short offline Completed without error 00% 16975 - # 9 Short offline Completed without error 00% 16892 - #10 Short offline Completed without error 00% 16751 - #11 Short offline Completed without error 00% 16608 - #12 Short offline Completed without error 00% 16467 - #13 Short offline Completed without error 00% 16326 - #14 Short offline Completed without error 00% 16185 - #15 Short offline Completed without error 00% 16050 - #16 Short offline Completed without error 00% 16020 - #17 Short offline Completed without error 00% 15934 - #18 Short offline Completed without error 00% 15801 - #19 Short offline Completed without error 00% 15660 - #20 Short offline Completed without error 00% 15518 - #21 Short offline Completed without error 00% 15377 - Selective Self-tests/Logging not supported
  5. Disk 1 happens to have just media files. I connected the disk directly to a windows PC and with FTK imager exported some of them, however neither media player classic nor VLC are able to playback these files. I have now remounted everything in my unraid server and using teracopy to move everything to a local hard disk and waiting to see if this allows me to open the files this way. Disk 4 was just added to the array but I never actually had anything stored on it if that helps. I have not done this yet, however checking dmesg I see a long list of bad sectors in disk1.
  6. you're right, thanks for reminding me, attaching diagnostics: cremonanas-diagnostics-20210515-1749.zip
  7. So I woke up today to two failed drives as per the below screenshot. The situation is as follows: Disk 3 - marked "unmountable: not mounted: I have connected it via USB HDD dock to my windows laptop. Both FTK Imager and DiskInternals LinuxReader are able to access the drive and show me the folders and files on it, although not sure if the data is actually readable, but folder structure seems intact. Disk 4 - Shown as failedBoth FTK and linux reader are showing me the filestructure of this drive. Since there are two failed drives, I can't mount the array, not even in maintenance mode. So what are my options here to try and retrieve the data and rebuild the array?
  8. Just finished, attached the report ST2000DM001-1CH164_Z340CGBC-20201030-1137.txt
  9. Recently some SMART errors started apprearing on one of my hard disks and my cache disk (I only have one SSD used as cache and It has some vms and other items that I store directly on it) below is what I am getting: MY HDD Smart Status is showing the below (I have errors on #197 and #198: ATTRIBUTES # ATTRIBUTE NAME FLAG VALUE WORST THRESHOLD TYPE UPDATED FAILED RAW VALUE 1 Raw read error rate 0x000f 102 088 006 Pre-fail Always Never 4021824 3 Spin up time 0x0003 095 094 000 Pre-fail Always Never 0 4 Start stop count 0x0032 098 098 020 Old age Always Never 2340 5 Reallocated sector count 0x0033 100 100 010 Pre-fail Always Never 0 7 Seek error rate 0x000f 078 060 030 Pre-fail Always Never 8747087847 9 Power on hours 0x0032 065 065 000 Old age Always Never 31220 (3y, 6m, 21d, 20h) 10 Spin retry count 0x0013 100 100 097 Pre-fail Always Never 0 12 Power cycle count 0x0032 098 098 020 Old age Always Never 2248 183 Runtime bad block 0x0032 100 100 000 Old age Always Never 0 184 End-to-end error 0x0032 100 100 099 Old age Always Never 0 187 Reported uncorrect 0x0032 100 100 000 Old age Always Never 0 188 Command timeout 0x0032 100 100 000 Old age Always Never 0 0 0 189 High fly writes 0x003a 100 100 000 Old age Always Never 0 190 Airflow temperature cel 0x0022 057 045 045 Old age Always In the past 43 (min/max 23/48) 191 G-sense error rate 0x0032 100 100 000 Old age Always Never 0 192 Power-off retract count 0x0032 100 100 000 Old age Always Never 172 193 Load cycle count 0x0032 013 013 000 Old age Always Never 175626 194 Temperature celsius 0x0022 043 055 000 Old age Always Never 43 (0 13 0 0 0) 197 Current pending sector 0x0012 100 100 000 Old age Always Never 32 198 Offline uncorrectable 0x0010 100 100 000 Old age Offline Never 32 199 UDMA CRC error count 0x003e 200 200 000 Old age Always Never 0 240 Head flying hours 0x0000 100 253 000 Old age Offline Never 29091h+44m+48.259s 241 Total lbas written 0x0000 100 253 000 Old age Offline Never 14692012755 242 Total lbas read 0x0000 100 253 000 Old age Offline Never 245614326568 MY SSD is showing the following errors on #5 and #187: ATTRIBUTES # ATTRIBUTE NAME FLAG VALUE WORST THRESHOLD TYPE UPDATED FAILED RAW VALUE 5 Reallocated sector count 0x0033 099 099 010 Pre-fail Always Never 2 9 Power on hours 0x0032 096 096 000 Old age Always Never 16037 (1y, 9m, 29d, 5h) 12 Power cycle count 0x0032 098 098 000 Old age Always Never 1113 177 Wear leveling count 0x0013 037 037 000 Pre-fail Always Never 1339 179 Used rsvd block count tot 0x0013 099 099 010 Pre-fail Always Never 2 181 Program fail count total 0x0032 100 100 010 Old age Always Never 0 182 Erase fail count total 0x0032 100 100 010 Old age Always Never 0 183 Runtime bad block 0x0013 099 099 010 Pre-fail Always Never 2 187 Uncorrectable error count 0x0032 099 099 000 Old age Always Never 2 190 Airflow temperature cel 0x0032 069 053 000 Old age Always Never 31 195 ECC error rate 0x001a 199 199 000 Old age Always Never 2 199 CRC error count 0x003e 100 100 000 Old age Always Never 0 235 POR recovery count 0x0012 099 099 000 Old age Always Never 86 241 Total lbas written 0x0032 099 099 000 Old age Always Never 151651063719 Should I be expecting any failures soon? Anything I can do about it (other than replacing)?
  10. I'm not sure what specific action solved my issue however I did the following things and I managed to solve the "UNREACHABLE SERVER" error: Removed plex container and the image Deleted plex folder from my appdata Updated unraid to Version 6.8.0-rc5 Re-installed plex On the plex initial configuration I set it up as a new server Once loaded everything started working If I went to my account, I could see that I still had my old corrupted servers running: I went to my account > selected broken servers and there is a remove button beneath it: Now everything is back to normal! Just need to rescan my whole library which takes a while. Hope it helps!
  11. I keep getting an UNREACHABLE error on the webUI. I've tried deleting and reinstalling the container but it didnt solve the issue. Also removed the plex folder from appdata just in case. Any idea what could be going on?
  12. Does anyone know how I can edit this container to start with sql_mode='' instead of the standard "ONLY_FULL_GROUP_BY,STRICT_TRANS_TABLES,NO_ZERO_IN_DATE,NO_ZERO_DATE,ERROR_FOR_DIVISION_BY_ZERO,NO_ENGINE_SUBSTITUTION" ? I am running a custom webapp that has to have this policy off. Only problem is each time I restart the docker container It reverts to the above.
  13. canyouseeme says no. but I have ports 80 and 443 forwarded to the unraid's IP port 180 and 1443 (which is what I set for letsencrypt). At any rate, I installed NGINX Reverse Proxy container, switched off letsencrypt and used ports 180 and 1443 for that. Nginx Reverse proxy worked immediately. I can even access it through the CNAME i have forwarded to duckdns.
  14. I'm following the spaceinvader guide here :https://www.youtube.com/watch?v=I0lhZc25Sro&feature=youtu.be however I keep getting stuck on the part where letsencypt is first booted up and tries to get a certificate and getting an error that I haven't been able to solve. Network is set up as follows: ISP -> Modem (bridge mode) -> Netgear ORBI Router - Ports 80, 443, mapped to Unraid's IP (not the custom net) ports 180, 1443 -> Unraid Server -> LetsEncrypt docker on customnet DuckDNS container set up and updating publicIP routinely. (ping to mydomain.duckdns.org reveals my external IP) When I fire up letsencrypt I get this in the logs: [s6-init] making user provided files available at /var/run/s6/etc...exited 0. [s6-init] ensuring user provided files have correct perms...exited 0. [fix-attrs.d] applying ownership & permissions fixes... [fix-attrs.d] done. [cont-init.d] executing container initialization scripts... [cont-init.d] 10-adduser: executing...-------------------------------------_ ()| | ___ _ __| | / __| | | / \| | \__ \ | | | () ||_| |___/ |_| \__/ Brought to you by linuxserver.io We gratefully accept donations at:https://www.linuxserver.io/donate/ -------------------------------------GID/UID------------------------------------- User uid: 99 User gid: 100 ------------------------------------- [cont-init.d] 10-adduser: exited 0. [cont-init.d] 20-config: executing... [cont-init.d] 20-config: exited 0. [cont-init.d] 30-keygen: executing...using keys found in /config/keys [cont-init.d] 30-keygen: exited 0. [cont-init.d] 50-config: executing...Variables set:PUID=99PGID=100TZ=Europe/BerlinURL=duckdns.orgSUBDOMAINS=mydomainEXTRA_DOMAINS=ONLY_SUBDOMAINS=trueDHLEVEL=2048VALIDATION=httpDNSPLUGIN=EMAIL=myemail@gmail.com STAGING=2048 bit DH parameters presentSUBDOMAINS entered, processingSUBDOMAINS entered, processingOnly subdomains, no URL in cert Sub-domains processed are: -d mysubdomain.duckdns.orgE-mail address entered: [email protected] validation is selectedGenerating new certificate Saving debug log to /var/log/letsencrypt/letsencrypt.logPlugins selected: Authenticator standalone, Installer NoneObtaining a new certificate Performing the following challenges:http-01 challenge for mysubdomain.duckdns.orgWaiting for verification... Challenge failed for domain mysubdomain.duckdns.org http-01 challenge for mysubdomain.duckdns.org Cleaning up challenges Some challenges have failed. IMPORTANT NOTES:- The following errors were reported by the server:Domain: mysubdomain.duckdns.orgType: connectionDetail: Fetchinghttp://mysubdomain.duckdns.org/.well-known/acme-challenge/TEN3u0g3N88iLRAEqryMvo6GJ71lsvCxP9hMbC5vwg8 :Connection refused To fix these errors, please make sure that your domain name wasentered correctly and the DNS A/AAAA record(s) for that domaincontain(s) the right IP address. Additionally, please check that your computer has a publicly routable IP address and that nofirewalls are preventing the server from communicating with the client. If you're using the webroot plugin, you should also verify that you are serving files from the webroot path you provided. ERROR: Cert does not exist! Please see the validation error above. The issue may be due to incorrect dns or port forwarding settings. Please fix your settings and recreate the container At this point, not sure where else to check
  15. Hi all, still new to unraid and getting used to how it works. I'm trying to install a CentOS Vm however it crashes when the first installer page loads. Attached screenshots of what I'm getting. Qemu Logs: 2019-03-24 17:36:15.054+0000: starting up libvirt version: 4.7.0, qemu version: 3.0.0, kernel: 4.18.20-unRAID, hostname: CremonaNas LC_ALL=C PATH=/bin:/sbin:/usr/bin:/usr/sbin HOME=/ QEMU_AUDIO_DRV=none /usr/local/sbin/qemu -name guest=WebServer,debug-threads=on -S -object secret,id=masterKey0,format=raw,file=/var/lib/libvirt/qemu/domain-2-WebServer/master-key.aes -machine pc-q35-3.0,accel=kvm,usb=off,dump-guest-core=off,mem-merge=off -cpu host -m 8192 -realtime mlock=off -smp 4,sockets=1,cores=4,threads=1 -uuid d3063725-384f-b0c2-6d57-b6b3e56e49fa -no-user-config -nodefaults -chardev socket,id=charmonitor,fd=27,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc,driftfix=slew -global kvm-pit.lost_tick_policy=delay -no-hpet -no-shutdown -boot strict=on -device pcie-root-port,port=0x10,chassis=1,id=pci.1,bus=pcie.0,multifunction=on,addr=0x2 -device pcie-root-port,port=0x11,chassis=2,id=pci.2,bus=pcie.0,addr=0x2.0x1 -device pcie-root-port,port=0x12,chassis=3,id=pci.3,bus=pcie.0,addr=0x2.0x2 -device pcie-root-port,port=0x13,chassis=4,id=pci.4,bus=pcie.0,addr=0x2.0x3 -device pcie-root-port,port=0x14,chassis=5,id=pci.5,bus=pcie.0,addr=0x2.0x4 -device pcie-root-port,port=0x15,chassis=6,id=pci.6,bus=pcie.0,addr=0x2.0x5 -device qemu-xhci,p2=15,p3=15,id=usb,bus=pcie.0,addr=0x7 -device virtio-serial-pci,id=virtio-serial0,bus=pci.2,addr=0x0 -drive file=/mnt/user/domains/WebServer/vdisk1.img,format=raw,if=none,id=drive-virtio-disk2,cache=writeback -device virtio-blk-pci,scsi=off,bus=pci.3,addr=0x0,drive=drive-virtio-disk2,id=virtio-disk2,bootindex=1,write-cache=on -drive file=/mnt/user/domains/WebServer/vdisk2.img,format=raw,if=none,id=drive-virtio-disk3,cache=writeback -device virtio-blk-pci,scsi=off,bus=pci.4,addr=0x0,drive=drive-virtio-disk3,id=virtio-disk3,write-cache=on -drive file=/mnt/user/isos/CentOS-7-x86_64-DVD-1810.iso,format=raw,if=none,id=drive-sata0-0-0,media=cdrom,readonly=on -device ide-cd,bus=ide.0,drive=drive-sata0-0-0,id=sata0-0-0,bootindex=2 -netdev tap,fd=29,id=hostnet0,vhost=on,vhostfd=30 -device virtio-net-pci,netdev=hostnet0,id=net0,mac=52:54:00:19:4e:e0,bus=pci.1,addr=0x0 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -chardev socket,id=charchannel0,fd=31,server,nowait -device virtserialport,bus=virtio-serial0.0,nr=1,chardev=charchannel0,id=channel0,name=org.qemu.guest_agent.0 -device usb-tablet,id=input0,bus=usb.0,port=1 -vnc 0.0.0.0:0,websocket=5700,password -k en-us -device qxl-vga,id=video0,ram_size=67108864,vram_size=67108864,vram64_size_mb=0,vgamem_mb=16,max_outputs=1,bus=pcie.0,addr=0x1 -device virtio-balloon-pci,id=balloon0,bus=pci.5,addr=0x0 -sandbox on,obsolete=deny,elevateprivileges=deny,spawn=deny,resourcecontrol=deny -msg timestamp=on 2019-03-24 17:36:15.054+0000: Domain id=2 is tainted: high-privileges 2019-03-24 17:36:15.054+0000: Domain id=2 is tainted: host-cpu 2019-03-24T17:36:15.099478Z qemu-system-x86_64: -chardev pty,id=charserial0: char device redirected to /dev/pts/1 (label charserial0) VM settings: <?xml version='1.0' encoding='UTF-8'?> <domain type='kvm' id='2'> <name>WebServer</name> <uuid>d3063725-384f-b0c2-6d57-b6b3e56e49fa</uuid> <metadata> <vmtemplate xmlns="unraid" name="CentOS" icon="centos.png" os="centos"/> </metadata> <memory unit='KiB'>8388608</memory> <currentMemory unit='KiB'>1048576</currentMemory> <memoryBacking> <nosharepages/> </memoryBacking> <vcpu placement='static'>4</vcpu> <cputune> <vcpupin vcpu='0' cpuset='0'/> <vcpupin vcpu='1' cpuset='1'/> <vcpupin vcpu='2' cpuset='2'/> <vcpupin vcpu='3' cpuset='3'/> </cputune> <resource> <partition>/machine</partition> </resource> <os> <type arch='x86_64' machine='pc-q35-3.0'>hvm</type> </os> <features> <acpi/> <apic/> </features> <cpu mode='host-passthrough' check='none'> <topology sockets='1' cores='4' threads='1'/> </cpu> <clock offset='utc'> <timer name='rtc' tickpolicy='catchup'/> <timer name='pit' tickpolicy='delay'/> <timer name='hpet' present='no'/> </clock> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/local/sbin/qemu</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='writeback'/> <source file='/mnt/user/domains/WebServer/vdisk1.img'/> <backingStore/> <target dev='hdc' bus='virtio'/> <boot order='1'/> <alias name='virtio-disk2'/> <address type='pci' domain='0x0000' bus='0x03' slot='0x00' function='0x0'/> </disk> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='writeback'/> <source file='/mnt/user/domains/WebServer/vdisk2.img'/> <backingStore/> <target dev='hdd' bus='virtio'/> <alias name='virtio-disk3'/> <address type='pci' domain='0x0000' bus='0x04' slot='0x00' function='0x0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/mnt/user/isos/CentOS-7-x86_64-DVD-1810.iso'/> <backingStore/> <target dev='hda' bus='sata'/> <readonly/> <boot order='2'/> <alias name='sata0-0-0'/> <address type='drive' controller='0' bus='0' target='0' unit='0'/> </disk> <controller type='usb' index='0' model='qemu-xhci' ports='15'> <alias name='usb'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </controller> <controller type='sata' index='0'> <alias name='ide'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x1f' function='0x2'/> </controller> <controller type='pci' index='0' model='pcie-root'> <alias name='pcie.0'/> </controller> <controller type='virtio-serial' index='0'> <alias name='virtio-serial0'/> <address type='pci' domain='0x0000' bus='0x02' slot='0x00' function='0x0'/> </controller> <controller type='pci' index='1' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='1' port='0x10'/> <alias name='pci.1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0' multifunction='on'/> </controller> <controller type='pci' index='2' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='2' port='0x11'/> <alias name='pci.2'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x1'/> </controller> <controller type='pci' index='3' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='3' port='0x12'/> <alias name='pci.3'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x2'/> </controller> <controller type='pci' index='4' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='4' port='0x13'/> <alias name='pci.4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x3'/> </controller> <controller type='pci' index='5' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='5' port='0x14'/> <alias name='pci.5'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x4'/> </controller> <controller type='pci' index='6' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='6' port='0x15'/> <alias name='pci.6'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x5'/> </controller> <interface type='bridge'> <mac address='52:54:00:19:4e:e0'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target type='isa-serial' port='0'> <model name='isa-serial'/> </target> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target type='serial' port='0'/> <alias name='serial0'/> </console> <channel type='unix'> <source mode='bind' path='/var/lib/libvirt/qemu/channel/target/domain-2-WebServer/org.qemu.guest_agent.0'/> <target type='virtio' name='org.qemu.guest_agent.0' state='disconnected'/> <alias name='channel0'/> <address type='virtio-serial' controller='0' bus='0' port='1'/> </channel> <input type='tablet' bus='usb'> <alias name='input0'/> <address type='usb' bus='0' port='1'/> </input> <input type='mouse' bus='ps2'> <alias name='input1'/> </input> <input type='keyboard' bus='ps2'> <alias name='input2'/> </input> <graphics type='vnc' port='5900' autoport='yes' websocket='5700' listen='0.0.0.0' keymap='en-us'> <listen type='address' address='0.0.0.0'/> </graphics> <video> <model type='qxl' ram='65536' vram='65536' vgamem='16384' heads='1' primary='yes'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x05' slot='0x00' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='dac' relabel='yes'> <label>+0:+100</label> <imagelabel>+0:+100</imagelabel> </seclabel> </domain> Is there Something I'm missing?