Jump to content

Removed Drives From a disk pool and add to an array - I messed up, how do I fix this?


Recommended Posts

This is my chia server, I had the last four drives in a disk pool on another server. I yanked them out and stuffed them into my cable spaghetti server.

Obviously, I didn't think through the single drive mode and didn't change the metadata parity settings.

Obviously it's just chia plots, but I'd rather not blow them away as it costs money to replot.

2022-05-05 12_56_45-Window.png

Link to comment

That's a new one to me. Maybe @JorgeB will have some ideas.

 

Since you don't have a parity drive, I'm thinking you can just do a new config and leave out 12 - 15, then add them to a pool so at least you will get back to a "normal" config and go from there. Whether you can split the 4 drive pool without moving data around, I don't think so, but like I said maybe JorgeB will have some options.

Link to comment
48 minutes ago, JonathanM said:

That's a new one to me. Maybe @JorgeB will have some ideas.

 

Since you don't have a parity drive, I'm thinking you can just do a new config and leave out 12 - 15, then add them to a pool so at least you will get back to a "normal" config and go from there. Whether you can split the 4 drive pool without moving data around, I don't think so, but like I said maybe JorgeB will have some options.

 

That was my initial urge to do, but I'm holding off on the off chance someone has advice on this.

 

I was thinking about this and I'm pretty sure the only reason this worked is because I DON'T have a parity drive. I'm pretty sure things would have stopped if I had a parity drive, because the parity drive would not be able to keep up the the changes.

 

I also think it would have corrupted parity, but that is a guess and nothing more.

Link to comment
20 minutes ago, eagle470 said:

I'm pretty sure the only reason this worked is because I DON'T have a parity drive. I'm pretty sure things would have stopped if I had a parity drive, because the parity drive would not be able to keep up the the changes.

If you had valid parity, the added drives would have been cleared to keep parity valid before they were added, erasing any filesystem on them.

 

I think it would be possible to have this config with parity, if you added the parity after the drives were already committed to the data slots.

 

Various Unraid functions may be broken as a result, but it would be interesting to see.

 

Parity doesn't care about data on the drives, so it probably would stay valid.

Link to comment
47 minutes ago, JonathanM said:

If you had valid parity, the added drives would have been cleared to keep parity valid before they were added, erasing any filesystem on them.

 

I think it would be possible to have this config with parity, if you added the parity after the drives were already committed to the data slots.

 

Various Unraid functions may be broken as a result, but it would be interesting to see.

 

Parity doesn't care about data on the drives, so it probably would stay valid.

The issue is the frequency of updates. After 30 minutes I already had 8+ million writes due to a balance kicking off immediately. There is ZERO way that a parity drive could keep up with that, unless it was an SSD and I'm not that well off.

 

So either the parity drive would slow the system to a near halt OR the system would start to drop parity writes as the queue grew past the buffer. 

 

I'm betting on the latter.

Link to comment
1 minute ago, eagle470 said:

So either the parity drive would slow the system to a near halt OR the system would start to drop parity writes as the queue grew past the buffer. 

 

I'm betting on the latter.

I'll take that bet. I think it would have slowed the writes to allow the parity to stay valid.

 

Perhaps JorgeB could recreate this on one of his test rigs. 🙂

Link to comment
6 hours ago, JorgeB said:

This happened to me before, and it can happen with parity, usually easily fixable, just no clear why a balance is running, if it started automatically post the diagnostics to see why.

I patched to rc6, last night while drunk. So no logs. 

 

Question though, is there a way to convert the meta data to single drive mode and remove the mirror?

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...