Preclear.sh results - Questions about your results? Post them here.


Recommended Posts

My friend asked me to post his pre-clear results here to see if everything came out fine.  Let me know if all is well

 

============================================================================
==
== Disk /dev/sdb has been successfully precleared
==
== Ran 1 preclear-disk cycle
==
== Using :Read block size = 8225280 Bytes
== Last Cycle's Pre Read Time á: 7:29:24 (74 MB/s)
== Last Cycle's Zeroing time á : 6:57:27 (79 MB/s)
== Last Cycle's Post Read Time : 13:06:15 (42 MB/s)
== Last Cycle's Total Time á á : 27:34:13
==
== Total Elapsed Time 27:34:13
==
== Disk Start Temperature: 22C
==
== Current Disk Temperature: 24C,
==
============================================================================
S.M.A.R.T. error count differences detected after pre-clear
note, some 'raw' values may change, but not be an indication of a problem
54c54
< á 1 Raw_Read_Error_Rate á á 0x002f á 100 á 253 á 051 á áPre-fail áAlways á á á - á á á 0
---
> á 1 Raw_Read_Error_Rate á á 0x002f á 200 á 200 á 051 á áPre-fail áAlways á á á - á á á 0
63c63
< 193 Load_Cycle_Count á á á á0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 24
---
> 193 Load_Cycle_Count á á á á0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 25
============================================================================
============================================================================
==
== S.M.A.R.T Initial Report
==
smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: á á WDC WD20EARS-00MVWB0
Serial Number: á áWD-WMAZA0613742
Firmware Version: 51.0AB51
User Capacity: á á2,000,398,934,016 bytes
Device is: á á á áNot in smartctl database [for details use: -P showall]
ATA Version is: á 8
ATA Standard is: áExact ATA specification draft version not indicated
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: á(0x80) Offline data collection activity
á á á á á á á á á á á á á á á á á á á áwas never started.
á á á á á á á á á á á á á á á á á á á áAuto Offline Data Collection: Enabled.
Self-test execution status: á á á( á 0) The previous self-test routine completed
á á á á á á á á á á á á á á á á á á á áwithout error or no self-test has ever
á á á á á á á á á á á á á á á á á á á ábeen run.
Total time to complete Offline
data collection: á á á á á á á á (37800) seconds.
Offline data collection
capabilities: á á á á á á á á á á(0x7b) SMART execute Offline immediate.
á á á á á á á á á á á á á á á á á á á áAuto Offline data collection on/off support.
á á á á á á á á á á á á á á á á á á á áSuspend Offline collection upon new
á á á á á á á á á á á á á á á á á á á ácommand.
á á á á á á á á á á á á á á á á á á á áOffline surface scan supported.
á á á á á á á á á á á á á á á á á á á áSelf-test supported.
á á á á á á á á á á á á á á á á á á á áConveyance Self-test supported.
á á á á á á á á á á á á á á á á á á á áSelective Self-test supported.
SMART capabilities: á á á á á á(0x0003) Saves SMART data before entering
á á á á á á á á á á á á á á á á á á á ápower-saving mode.
á á á á á á á á á á á á á á á á á á á áSupports SMART auto save timer.
Error logging capability: á á á á(0x01) Error logging supported.
á á á á á á á á á á á á á á á á á á á áGeneral Purpose Logging supported.
Short self-test routine
recommended polling time: á á á á( á 2) minutes.
Extended self-test routine
recommended polling time: á á á á( 255) minutes.
Conveyance self-test routine
recommended polling time: á á á á( á 5) minutes.
SCT capabilities: á á á á á á á(0x3035) SCT Status supported.
á á á á á á á á á á á á á á á á á á á áSCT Feature Control supported.
á á á á á á á á á á á á á á á á á á á áSCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME á á á á áFLAG á á VALUE WORST THRESH TYPE á á áUPDATED áWHEN_FAILED RAW_VALUE
á1 Raw_Read_Error_Rate á á 0x002f á 100 á 253 á 051 á áPre-fail áAlways á á á - á á á 0
á3 Spin_Up_Time á á á á á á0x0027 á 173 á 169 á 021 á áPre-fail áAlways á á á - á á á 6333
á4 Start_Stop_Count á á á á0x0032 á 100 á 100 á 000 á áOld_age á Always á á á - á á á 12
á5 Reallocated_Sector_Ct á 0x0033 á 200 á 200 á 140 á áPre-fail áAlways á á á - á á á 0
á7 Seek_Error_Rate á á á á 0x002e á 100 á 253 á 000 á áOld_age á Always á á á - á á á 0
á10 Spin_Retry_Count á á á á0x0032 á 100 á 253 á 000 á áOld_age á Always á á á - á á á 0
á11 Calibration_Retry_Count 0x0032 á 100 á 253 á 000 á áOld_age á Always á á á - á á á 0
á12 Power_Cycle_Count á á á 0x0032 á 100 á 100 á 000 á áOld_age á Always á á á - á á á 10
192 Power-Off_Retract_Count 0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 9
193 Load_Cycle_Count á á á á0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 24
196 Reallocated_Event_Count 0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 0
197 Current_Pending_Sector á0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 0
198 Offline_Uncorrectable á 0x0030 á 100 á 253 á 000 á áOld_age á Offline á á á- á á á 0
199 UDMA_CRC_Error_Count á á0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 0
200 Multi_Zone_Error_Rate á 0x0008 á 100 á 253 á 000 á áOld_age á Offline á á á- á á á 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. á[To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
áSPAN áMIN_LBA áMAX_LBA áCURRENT_TEST_STATUS
á á1 á á á á0 á á á á0 áNot_testing
á á2 á á á á0 á á á á0 áNot_testing
á á3 á á á á0 á á á á0 áNot_testing
á á4 á á á á0 á á á á0 áNot_testing
á á5 á á á á0 á á á á0 áNot_testing
Selective self-test flags (0x0):
áAfter scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
==
============================================================================



============================================================================
==
== S.M.A.R.T Final Report
==
smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: á á WDC WD20EARS-00MVWB0
Serial Number: á áWD-WMAZA0613742
Firmware Version: 51.0AB51
User Capacity: á á2,000,398,934,016 bytes
Device is: á á á áNot in smartctl database [for details use: -P showall]
ATA Version is: á 8
ATA Standard is: áExact ATA specification draft version not indicated
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: á(0x80) Offline data collection activity
á á á á á á á á á á á á á á á á á á á áwas never started.
á á á á á á á á á á á á á á á á á á á áAuto Offline Data Collection: Enabled.
Self-test execution status: á á á( á 0) The previous self-test routine completed
á á á á á á á á á á á á á á á á á á á áwithout error or no self-test has ever
á á á á á á á á á á á á á á á á á á á ábeen run.
Total time to complete Offline
data collection: á á á á á á á á (37800) seconds.
Offline data collection
capabilities: á á á á á á á á á á(0x7b) SMART execute Offline immediate.
á á á á á á á á á á á á á á á á á á á áAuto Offline data collection on/off support.
á á á á á á á á á á á á á á á á á á á áSuspend Offline collection upon new
á á á á á á á á á á á á á á á á á á á ácommand.
á á á á á á á á á á á á á á á á á á á áOffline surface scan supported.
á á á á á á á á á á á á á á á á á á á áSelf-test supported.
á á á á á á á á á á á á á á á á á á á áConveyance Self-test supported.
á á á á á á á á á á á á á á á á á á á áSelective Self-test supported.
SMART capabilities: á á á á á á(0x0003) Saves SMART data before entering
á á á á á á á á á á á á á á á á á á á ápower-saving mode.
á á á á á á á á á á á á á á á á á á á áSupports SMART auto save timer.
Error logging capability: á á á á(0x01) Error logging supported.
á á á á á á á á á á á á á á á á á á á áGeneral Purpose Logging supported.
Short self-test routine
recommended polling time: á á á á( á 2) minutes.
Extended self-test routine
recommended polling time: á á á á( 255) minutes.
Conveyance self-test routine
recommended polling time: á á á á( á 5) minutes.
SCT capabilities: á á á á á á á(0x3035) SCT Status supported.
á á á á á á á á á á á á á á á á á á á áSCT Feature Control supported.
á á á á á á á á á á á á á á á á á á á áSCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME á á á á áFLAG á á VALUE WORST THRESH TYPE á á áUPDATED áWHEN_FAILED RAW_VALUE
á1 Raw_Read_Error_Rate á á 0x002f á 200 á 200 á 051 á áPre-fail áAlways á á á - á á á 0
á3 Spin_Up_Time á á á á á á0x0027 á 173 á 169 á 021 á áPre-fail áAlways á á á - á á á 6333
á4 Start_Stop_Count á á á á0x0032 á 100 á 100 á 000 á áOld_age á Always á á á - á á á 12
á5 Reallocated_Sector_Ct á 0x0033 á 200 á 200 á 140 á áPre-fail áAlways á á á - á á á 0
á7 Seek_Error_Rate á á á á 0x002e á 100 á 253 á 000 á áOld_age á Always á á á - á á á 0
á10 Spin_Retry_Count á á á á0x0032 á 100 á 253 á 000 á áOld_age á Always á á á - á á á 0
á11 Calibration_Retry_Count 0x0032 á 100 á 253 á 000 á áOld_age á Always á á á - á á á 0
á12 Power_Cycle_Count á á á 0x0032 á 100 á 100 á 000 á áOld_age á Always á á á - á á á 10
192 Power-Off_Retract_Count 0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 9
193 Load_Cycle_Count á á á á0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 25
196 Reallocated_Event_Count 0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 0
197 Current_Pending_Sector á0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 0
198 Offline_Uncorrectable á 0x0030 á 100 á 253 á 000 á áOld_age á Offline á á á- á á á 0
199 UDMA_CRC_Error_Count á á0x0032 á 200 á 200 á 000 á áOld_age á Always á á á - á á á 0
200 Multi_Zone_Error_Rate á 0x0008 á 100 á 253 á 000 á áOld_age á Offline á á á- á á á 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. á[To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
áSPAN áMIN_LBA áMAX_LBA áCURRENT_TEST_STATUS
á á1 á á á á0 á á á á0 áNot_testing
á á2 á á á á0 á á á á0 áNot_testing
á á3 á á á á0 á á á á0 áNot_testing
á á4 á á á á0 á á á á0 áNot_testing
á á5 á á á á0 á á á á0 áNot_testing
Selective self-test flags (0x0):
áAfter scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Link to comment

For future reference, always upgrade to the latest version of preclear_disk.sh available at the time BEFORE you start your preclear cycle(s). The new results format enable you to self diagnose with ease.

 

We can not tell if your disk is good since you did not include the full SMART report. We can only tell you that 3 attributes changed normalized values that are no where near their thresholds. If the disk was failing before the preclear on some attributes they're failing the same way after the preclear. If the disk was not failing before the preclear on some attributes, they're not failing the same way after the preclear.

Link to comment

Precleared 3x WD20EARS (jumpered, -a) and one of them came up with re-allocated sectors. Is this drive okay to use?

 

 

============================================================================

==

== Disk /dev/sdd has been successfully precleared

== with a starting sector of 63

============================================================================

** Changed attributes in files: /tmp/smart_start_sdd  /tmp/smart_finish_sdd

                ATTRIBUTE  NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS      RAW_VALUE

      Raw_Read_Error_Rate =  200    100          051        ok          0

    Reallocated_Sector_Ct =  199    200          140        ok          2

  Reallocated_Event_Count =  199    200          000        ok          1

No SMART attributes are FAILING_NOW

0 sectors are pending re-allocation.

2 sectors have been re-allocated.

Link to comment

Precleared 3x WD20EARS (jumpered, -a) and one of them came up with re-allocated sectors. Is this drive okay to use?

 

 

============================================================================

==

== Disk /dev/sdd has been successfully precleared

== with a starting sector of 63

============================================================================

** Changed attributes in files: /tmp/smart_start_sdd  /tmp/smart_finish_sdd

                ATTRIBUTE   NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS      RAW_VALUE

      Raw_Read_Error_Rate =   200     100          051        ok          0

    Reallocated_Sector_Ct =   199     200          140        ok          2

  Reallocated_Event_Count =   199     200          000        ok          1

No SMART attributes are FAILING_NOW

0 sectors are pending re-allocation.

2 sectors have been re-allocated.

I'd run another pre-clear cycle on it.  If additional sectors are re-allocated, it might be a candidate for an RMA.

If nothing changes, then go ahead and use it, most disks have several thousand spare sectors.  Just keep an eye on it.  If you see the number of re-alllocated sectors increasing, or continual "read" errors on the web-management console, consider the RMA.

 

Oh  yes, I see you are using an older version of the pre-clear script.  Please download and use the newest one for your next cycle.  I've been making continual improvements in the output report.

 

Joe L.

Link to comment

 

Thanks, will do Joe. BTW, do I have to restart the server after copying over the new preclear_disk.sh to the /boot directory?

No.  This is not "windows"  No need to reboot.

 

You almost never need to "reboot" unless you are installing a new version of unRAID, or you will be adding/removing disks or other hardware,  or some wayward process has used up all your system memory (and processes were killed trying to make room for running ones)

 

Joe L.

 

Link to comment

To be fair, the latest versions of Windows hardly need reboot either.

No, they crash on their own....

 

Three blue-screens of death this week on my Vista Laptop.   

 

Following "microsoft's" advice to debug it says the problem is fixed in SP1.  But I have SP1 installed, and everything else they have as updates... all except IE8 and Silverlight. (I want neither)

Oh yes, memtest run overnight come up clean... so it is not ram related.

 

So no, I don't have to reboot every once in a while.... it never stays up that long...  argh.... 

Link to comment

I'm sorry to hear about your Vista grief. I wish everyone could have the kind of success I have with my Windows and Linux systems.

 

I've had success with my Windows 7 development environments. The only need to reboot is for the rare installing of new devices that require additional device drivers or system services which is the same case for Linux. Sometimes I don't need to reboot in Windows 7 with some of the device driver upgrades, like for the NICs and Graphic Cards.

 

Anyways, back on topic... Any thoughts to having preclear_disk.sh do a quick version check on startup against the unMENU repository to see if there's a newer version available, if so prompt the user if they would like to continue anyways? I'm not proposing a self-updating feature, just a quick warning to the users to upgrade. It's been nearly two weeks since your report simplifications and there's still people asking for feedback on the old formats. Now I know this won't help those running the older versions, but it would cut down on this sort of thing in the future.

Link to comment

hi guys,

 

everything looks ok from what i gather, but since this is my first unRAID build a second opinion would put me more at ease - if any more info is needed, please let me know.

There is no need to post the smart reports.

But, you did not post the final preclear report, and that would have told you the same as I will

 

I did not see any attributes marked as FAILING_NOW

There are no sectors re-allocated, or pending re-allocation.

 

Enjoy your new drives.

 

Joe L.

Link to comment

hmm, must have missed that - was trying to stay up for the end of the preclear cycle, but once i woke up in the living room at 4am on the couch i just went to bed. i'll keep an eye out for the final preclear reports when i preclear the next 3 drives that are currently en-route.

 

thanks!

You will find a copy of it in your syslog.  (if you've not rebooted)

 

Joe L.

Link to comment

Well done my first pre_clear on a brand new 1TB drive. As putting it off until i'd finished work on the case the server will live in but i'm short on space so needed to use it now.

 

All went fine, a lot easier than i was expecting since i count myself as a bit of a unix'y noob. Few things on the SMART side i want to run over tho:

 

at the end of the pre_clear i got a output of SMART stats, everything is on 'OK' for status but 2 have 'near_thresh' and am not sure if this should be a worrying sign. The two in question are:

 

Spin_Retry_Count (New_Val=100, Old_Val=100, Failure_Threshold=97, Status=near_Thresh, Raw_Value=0)

End-To-End_Error (New_Val=100, Old_Val=100, Failure_Threshold=99, Status=near_Thresh, Raw_Value=0)

 

What does the near_thresh mean?? I would take this liturally saying something is near is threshold which in my mind would ring alarm bells :)

 

Given my lack of real knowledge on SMART attributes can someone advice before i assign this drive for data.

 

Link to comment

Well done my first pre_clear on a brand new 1TB drive. As putting it off until i'd finished work on the case the server will live in but i'm short on space so needed to use it now.

 

All went fine, a lot easier than i was expecting since i count myself as a bit of a unix'y noob. Few things on the SMART side i want to run over tho:

 

at the end of the pre_clear i got a output of SMART stats, everything is on 'OK' for status but 2 have 'near_thresh' and am not sure if this should be a worrying sign. The two in question are:

 

Spin_Retry_Count (New_Val=100, Old_Val=100, Failure_Threshold=97, Status=near_Thresh, Raw_Value=0)

End-To-End_Error (New_Val=100, Old_Val=100, Failure_Threshold=99, Status=near_Thresh, Raw_Value=0)

 

What does the near_thresh mean?? I would take this liturally saying something is near is threshold which in my mind would ring alarm bells :)

 

Given my lack of real knowledge on SMART attributes can someone advice before i assign this drive for data.

 

It entirely depends on the manufacturer as to what it indicates. 

Near-threshold simply means the VALUE is within 25 of its failure threshold.    Since the manufacturer gets to "normalize" the data, it could have millions of "errors" before deciding to change the normalized value down a count or two to where it hits the failure threshold.

 

So... you are more informed, but nobody has a clue why the manufacturers set the thresholds as they do.

Since the "Spin-Retry" count is zero, I'd guess the disk has never had to re-spin a disk to get it up to speed.  Same with "End-to-End" errors..  The Raw value is zero, so (assuming they show the raw data) it too has never failed.  I would not worry too much about them.

 

I wish interpreting SMART reports was easier, or there was a true "standard" all disks followed, but there is not.

 

Joe L.

Link to comment

I used the new preclear script.  Is this hard drive fine?

 

============================================================================
Feb  1 23:34:26 media preclear_disk-diff[6205]: ==
Feb  1 23:34:26 media preclear_disk-diff[6205]: == S.M.A.R.T Initial Report for /dev/sdd 
Feb  1 23:34:26 media preclear_disk-diff[6205]: ==
Feb  1 23:34:26 media preclear_disk-diff[6205]: Disk: /dev/sdd
Feb  1 23:34:26 media preclear_disk-diff[6205]: smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
Feb  1 23:34:26 media preclear_disk-diff[6205]: Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: === START OF INFORMATION SECTION ===
Feb  1 23:34:26 media preclear_disk-diff[6205]: Device Model:     WDC WD20EARS-00MVWB0
Feb  1 23:34:26 media preclear_disk-diff[6205]: Serial Number:    WD-WMAZA2751951
Feb  1 23:34:26 media preclear_disk-diff[6205]: Firmware Version: 51.0AB51
Feb  1 23:34:26 media preclear_disk-diff[6205]: User Capacity:    2,000,398,934,016 bytes
Feb  1 23:34:26 media preclear_disk-diff[6205]: Device is:        Not in smartctl database [for details use: -P showall]
Feb  1 23:34:26 media preclear_disk-diff[6205]: ATA Version is:   8
Feb  1 23:34:26 media preclear_disk-diff[6205]: ATA Standard is:  Exact ATA specification draft version not indicated
Feb  1 23:34:26 media preclear_disk-diff[6205]: Local Time is:    Mon Jan 31 21:19:03 2011 PST
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART support is: Available - device has SMART capability.
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART support is: Enabled
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: === START OF READ SMART DATA SECTION ===
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART overall-health self-assessment test result: PASSED
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: General SMART Values:
Feb  1 23:34:26 media preclear_disk-diff[6205]: Offline data collection status:  (0x80)^IOffline data collection activity
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Iwas never started.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IAuto Offline Data Collection: Enabled.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Self-test execution status:      (   0)^IThe previous self-test routine completed
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Iwithout error or no self-test has ever 
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Ibeen run.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Total time to complete Offline 
Feb  1 23:34:26 media preclear_disk-diff[6205]: data collection: ^I^I (36480) seconds.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Offline data collection
Feb  1 23:34:26 media preclear_disk-diff[6205]: capabilities: ^I^I^I (0x7b) SMART execute Offline immediate.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IAuto Offline data collection on/off support.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISuspend Offline collection upon new
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Icommand.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IOffline surface scan supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISelf-test supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IConveyance Self-test supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISelective Self-test supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART capabilities:            (0x0003)^ISaves SMART data before entering
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Ipower-saving mode.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISupports SMART auto save timer.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Error logging capability:        (0x01)^IError logging supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IGeneral Purpose Logging supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Short self-test routine 
Feb  1 23:34:26 media preclear_disk-diff[6205]: recommended polling time: ^I (   2) minutes.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Extended self-test routine
Feb  1 23:34:26 media preclear_disk-diff[6205]: recommended polling time: ^I ( 255) minutes.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Conveyance self-test routine
Feb  1 23:34:26 media preclear_disk-diff[6205]: recommended polling time: ^I (   5) minutes.
Feb  1 23:34:26 media preclear_disk-diff[6205]: SCT capabilities: ^I       (0x3035)^ISCT Status supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISCT Feature Control supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISCT Data Table supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART Attributes Data Structure revision number: 16
Feb  1 23:34:26 media preclear_disk-diff[6205]: Vendor Specific SMART Attributes with Thresholds:
Feb  1 23:34:26 media preclear_disk-diff[6205]: ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
Feb  1 23:34:26 media preclear_disk-diff[6205]:   1 Raw_Read_Error_Rate     0x002f   100   253   051    Pre-fail  Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:   3 Spin_Up_Time            0x0027   253   253   021    Pre-fail  Always       -       1083
Feb  1 23:34:26 media preclear_disk-diff[6205]:   4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       15
Feb  1 23:34:26 media preclear_disk-diff[6205]:   5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:   7 Seek_Error_Rate         0x002e   100   253   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:   9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:  10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:  11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:  12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       13
Feb  1 23:34:26 media preclear_disk-diff[6205]: 192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       11
Feb  1 23:34:26 media preclear_disk-diff[6205]: 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       16
Feb  1 23:34:26 media preclear_disk-diff[6205]: 194 Temperature_Celsius     0x0022   124   120   000    Old_age   Always       -       26
Feb  1 23:34:26 media preclear_disk-diff[6205]: 196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 199 UDMA_CRC_Error_Count    0x0032   200   253   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART Error Log Version: 1
Feb  1 23:34:26 media preclear_disk-diff[6205]: No Errors Logged
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART Self-test log structure revision number 1
Feb  1 23:34:26 media preclear_disk-diff[6205]: No self-tests have been logged.  [To run self-tests, use: smartctl -t]
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART Selective self-test log data structure revision number 1
Feb  1 23:34:26 media preclear_disk-diff[6205]:  SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
Feb  1 23:34:26 media preclear_disk-diff[6205]:     1        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]:     2        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]:     3        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]:     4        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]:     5        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]: Selective self-test flags (0x0):
Feb  1 23:34:26 media preclear_disk-diff[6205]:   After scanning selected spans, do NOT read-scan remainder of disk.
Feb  1 23:34:26 media preclear_disk-diff[6205]: If Selective self-test is pending on power-up, resume after 0 minute delay. 
Feb  1 23:34:26 media preclear_disk-diff[6205]: ==
Feb  1 23:34:26 media preclear_disk-diff[6205]: ============================================================================
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: ============================================================================
Feb  1 23:34:26 media preclear_disk-diff[6205]: ==
Feb  1 23:34:26 media preclear_disk-diff[6205]: == S.M.A.R.T Final Report for /dev/sdd 
Feb  1 23:34:26 media preclear_disk-diff[6205]: ==
Feb  1 23:34:26 media preclear_disk-diff[6205]: Disk: /dev/sdd
Feb  1 23:34:26 media preclear_disk-diff[6205]: smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build)
Feb  1 23:34:26 media preclear_disk-diff[6205]: Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: === START OF INFORMATION SECTION ===
Feb  1 23:34:26 media preclear_disk-diff[6205]: Device Model:     WDC WD20EARS-00MVWB0
Feb  1 23:34:26 media preclear_disk-diff[6205]: Serial Number:    WD-WMAZA2751951
Feb  1 23:34:26 media preclear_disk-diff[6205]: Firmware Version: 51.0AB51
Feb  1 23:34:26 media preclear_disk-diff[6205]: User Capacity:    2,000,398,934,016 bytes
Feb  1 23:34:26 media preclear_disk-diff[6205]: Device is:        Not in smartctl database [for details use: -P showall]
Feb  1 23:34:26 media preclear_disk-diff[6205]: ATA Version is:   8
Feb  1 23:34:26 media preclear_disk-diff[6205]: ATA Standard is:  Exact ATA specification draft version not indicated
Feb  1 23:34:26 media preclear_disk-diff[6205]: Local Time is:    Tue Feb  1 23:34:25 2011 PST
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART support is: Available - device has SMART capability.
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART support is: Enabled
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: === START OF READ SMART DATA SECTION ===
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART overall-health self-assessment test result: PASSED
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: General SMART Values:
Feb  1 23:34:26 media preclear_disk-diff[6205]: Offline data collection status:  (0x84)^IOffline data collection activity
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Iwas suspended by an interrupting command from host.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IAuto Offline Data Collection: Enabled.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Self-test execution status:      (   0)^IThe previous self-test routine completed
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Iwithout error or no self-test has ever 
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Ibeen run.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Total time to complete Offline 
Feb  1 23:34:26 media preclear_disk-diff[6205]: data collection: ^I^I (36480) seconds.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Offline data collection
Feb  1 23:34:26 media preclear_disk-diff[6205]: capabilities: ^I^I^I (0x7b) SMART execute Offline immediate.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IAuto Offline data collection on/off support.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISuspend Offline collection upon new
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Icommand.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IOffline surface scan supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISelf-test supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IConveyance Self-test supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISelective Self-test supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART capabilities:            (0x0003)^ISaves SMART data before entering
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^Ipower-saving mode.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISupports SMART auto save timer.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Error logging capability:        (0x01)^IError logging supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^IGeneral Purpose Logging supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Short self-test routine 
Feb  1 23:34:26 media preclear_disk-diff[6205]: recommended polling time: ^I (   2) minutes.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Extended self-test routine
Feb  1 23:34:26 media preclear_disk-diff[6205]: recommended polling time: ^I ( 255) minutes.
Feb  1 23:34:26 media preclear_disk-diff[6205]: Conveyance self-test routine
Feb  1 23:34:26 media preclear_disk-diff[6205]: recommended polling time: ^I (   5) minutes.
Feb  1 23:34:26 media preclear_disk-diff[6205]: SCT capabilities: ^I       (0x3035)^ISCT Status supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISCT Feature Control supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: ^I^I^I^I^ISCT Data Table supported.
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART Attributes Data Structure revision number: 16
Feb  1 23:34:26 media preclear_disk-diff[6205]: Vendor Specific SMART Attributes with Thresholds:
Feb  1 23:34:26 media preclear_disk-diff[6205]: ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
Feb  1 23:34:26 media preclear_disk-diff[6205]:   1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:   3 Spin_Up_Time            0x0027   253   253   021    Pre-fail  Always       -       1083
Feb  1 23:34:26 media preclear_disk-diff[6205]:   4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       15
Feb  1 23:34:26 media preclear_disk-diff[6205]:   5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:   7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:   9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       26
Feb  1 23:34:26 media preclear_disk-diff[6205]:  10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:  11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]:  12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       13
Feb  1 23:34:26 media preclear_disk-diff[6205]: 192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       11
Feb  1 23:34:26 media preclear_disk-diff[6205]: 193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       17
Feb  1 23:34:26 media preclear_disk-diff[6205]: 194 Temperature_Celsius     0x0022   123   120   000    Old_age   Always       -       27
Feb  1 23:34:26 media preclear_disk-diff[6205]: 196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART Error Log Version: 1
Feb  1 23:34:26 media preclear_disk-diff[6205]: No Errors Logged
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART Self-test log structure revision number 1
Feb  1 23:34:26 media preclear_disk-diff[6205]: No self-tests have been logged.  [To run self-tests, use: smartctl -t]
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: 
Feb  1 23:34:26 media preclear_disk-diff[6205]: SMART Selective self-test log data structure revision number 1
Feb  1 23:34:26 media preclear_disk-diff[6205]:  SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
Feb  1 23:34:26 media preclear_disk-diff[6205]:     1        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]:     2        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]:     3        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]:     4        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]:     5        0        0  Not_testing
Feb  1 23:34:26 media preclear_disk-diff[6205]: Selective self-test flags (0x0):
Feb  1 23:34:26 media preclear_disk-diff[6205]:   After scanning selected spans, do NOT read-scan remainder of disk.
Feb  1 23:34:26 media preclear_disk-diff[6205]: If Selective self-test is pending on power-up, resume after 0 minute delay. 
Feb  1 23:34:26 media preclear_disk-diff[6205]: ==
Feb  1 23:34:26 media preclear_disk-diff[6205]: ============================================================================
Feb  1 23:34:26 media preclear_disk-diff[6205]:  

Link to comment

I used the new preclear script.  Is this hard drive fine?

Those are the raw smart reports.  The final preclear report should be available in the preclear_reports  subdirectory of the flash drive. (assuming you are using the new preclear script.)  It tells you in English if the preclear was successful.  The SMART reports do not.

 

Joe L.

 

 

Link to comment

I used the preclear script right before your latest release.  It was the one that supported advanced format drives.  I looked in my flash directory but did not find a preclear_reports anywhere on it.

 

When my preclear had finished, I typed:

 

grep preclear /var/log/syslog | todos >> /boot/preclear_results.txt

 

...so I don't know if that affected the output of the results.

 

What steps must I follow so that I can get the simple-to-read results for my next drive preclearing?

Link to comment

I used the preclear script right before your latest release.  It was the one that supported advanced format drives.  

 

The first version to support advanced format drives also includes the new report format as well. It was released on Jan 14, 2011 as Version .9.9. I know it at least displays the results to standard out. All you have to do is look at the display used to invoke the script. In my syslog I also have the human readable results, it's listed as "preclear_disk-diff".

 

How did you invoke the script?

 

Link to comment

I used the preclear script right before your latest release.  It was the one that supported advanced format drives.  I looked in my flash directory but did not find a preclear_reports anywhere on it.

 

When my preclear had finished, I typed:

 

grep preclear /var/log/syslog | todos >> /boot/preclear_results.txt

 

...so I don't know if that affected the output of the results.

 

What steps must I follow so that I can get the simple-to-read results for my next drive preclearing?

 

Your version of the preclear script may be 7 versions old.  (I've been busy  ;))

What do you get when you type:

preclear_disk.sh -v

 

# Version .9.9 - Changes to not perform pre-read in multi-cycles of use immediately after post-read

#              - added "-l" option to list device names of disks not in the array.

#              - modifications to final output report for easier interpetation

#              - modification to name the temp files after the disks being cleared.

#              - Added ability to start partition at sector 64 with -A option.

# Version .9.9a - improvements to analysis report

# Version .9.9b - more improvements to analysis report

#               - fixed bug when parsing config/disk.cfg for existing assigned disks.

# Version .9.9c - fixed bug where date format change in 5.0 unRAID changed and

#                 caused "-l" option to not work as expected.

#               - more improvements to analysis report

# Version .9.9d - more improvements to analysis report

# Version 1.1   - added -C 64 and -C 63 options to convert precleared drives from

#                 sector 63 start to sector 64 start.

#               - added display of command line arguments to initial confirmation screen

#               - added -W option to skip pre-read phase and start with "write" phase.

#               - added -V option to skip pre-read and "clear" and only

#                 perform the post-read verify.

# Version 1.2   - fixed "-l" option to not exclude disks with only a "scsi-" entry in /dev/disk/by-id

# Version 1.3   - Added logic to read desired "default" Partition Type from /boot/config.

#               - Added logic to save dated copies of the final preclear and SMART reports to a

#                 "preclear_reports" subdirectory on the flash drive.

#               - Added "-R" option to suppress the copy of final reports to a "preclear_reports"

#                 directory on the flash drive. (they are always in /tmp until you reboot)

 

 

Step 1.  Download the newest preclear_disk.sh  

Step 2.  If you have about 10 hours can use the new verify feature on the disk you just pre-cleared.  It skips the pre-read and zeroing, and just does the post-read verify and final report.

Type

preclear_disk.sh -V /dev/sdd

 

Then, when it is done look in the preclear_reports directory on the flash drive.

 

Joe L.

Link to comment

This is a brand new WD20EARS. The report looks good, but I'd like to have another set of experienced eyes look it over, please.

 

Disk: /dev/sdc
smartctl version 5.38 [i486-slackware-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD20EARS-00MVWB0
Serial Number:    WD-WMAZA3212657
Firmware Version: 51.0AB51
User Capacity:    2,000,398,934,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Fri Feb  4 20:19:37 2011 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84)	Offline data collection activity
				was suspended by an interrupting command from host.
				Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
				without error or no self-test has ever 
				been run.
Total time to complete Offline 
data collection: 		 (38100) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
				Auto Offline data collection on/off support.
				Suspend Offline collection upon new
				command.
				Offline surface scan supported.
				Self-test supported.
				Conveyance Self-test supported.
				Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
				power-saving mode.
				Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
				General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 255) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x3035)	SCT Status supported.
				SCT Feature Control supported.
				SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   253   253   021    Pre-fail  Always       -       1125
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       10
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       26
10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       8
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       7
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       15
194 Temperature_Celsius     0x0022   119   116   000    Old_age   Always       -       31
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.