wickedathletes

I was wondering, after comparing to a new 6.2b21 go file is any of the following old stuff I can remove? cd /boot/packages && find . -name '*.auto_install' -type f -print | sort | xargs -n1 sh -c unraid_notify start I notice during bootup is complains about unraid_notify. I searched the forums but didn't see to much about if this was truncated or not.

so oddly enough 3rd reboot was the charm... haha. I can now write to it. The syslogs showed nothing that I noticed.

So I just moved 4TB off of a reiserFS formatted drive so I could finally switch all my drives to xfs. However, after formatting it to xfs nothing can write to it. Windows just hangs after moving about 200mb and dolphin hangs or eventually says Disk is Full. Any thoughts? I dont see anything in my dolphin or system logs. I ran a SMART short test and it passed fine.

My server got hung up when trying to use dolphin to push 2TB (basically I did not have enough free on the drive I was moving it too). I had to reboot the server. Dolphin wont connect now and I get this error: Fatal server error: Server is already active for display 1 If this server is no longer running, remove /tmp/.X1-lock and start again. Openbox-Message: Failed to open the display from the DISPLAY environment variable.

figured I would check to see if this was normal or I have something on I shouldn't or something, I get these warning every boot up: avahi-daemon 0.6.31 starting up. 6 3000 /config/Library/Application Support d dbus[52]: [system] org.freedesktop.DBus.Error.AccessDenied: Failed to set fd limit to 65536: Operation not permitted No service file found in /etc/avahi/services. *** WARNING: Detected another IPv4 mDNS stack running on this host. This makes mDNS unreliable and is thus not recommended. *** socket() failed: Address family not supported by protocol Failed to create IPv6 socket, proceeding in IPv4 only mode socket() failed: Address family not supported by protocol Joining mDNS multicast group on interface virbr0.IPv4 with address 192.168.122.1. New relevant i

On unRaid Main screen, there's a very tiny little picture of a hard drive immediately to the left of the drive model # / serial #. Clicking it will bring up all the ata messages for that particular drive. Keep clicking til you find the appropriate drive thanks! Oddly enough its not the failed drive I had but the drive I am doing the Dolphin copy from right now. Its also my only reiserfs drive left (if that matters). I didn't have the storage until recently to convert that drive over to xfs like everything else. Could this be a serious issue or just something that went funky when I tried to do a copy? Originally in dolphin I tried browsing through samba share and copying that way but it failed for me (I didn't see the root icon at first). Maybe that was the corresponding error?

Why not install either the dolphin or krusader docker app, which gives you an interface similar to windows, but avoids the extra time involved via windows in moving everything back and forth over the network HAHAHA, I was just about to ask this lol. oh well... this is gonna be interesting... Like an idiot I kicked off 120GB transfer which should finish without an issue but my server does maintenance every night at 2am (2.5 hrs) and it reboots dockers. I assume if the docker is restarted the transfer stops? trying out dolphin now, this is definitely ideal over a windows app if it looks and works good just don't close the transfer window. The transfer will still continue, but you won't be able to get the transfer window back open until it finishes

can this be coorelated back to a specific drive or is this completely unrelated. Nothing is having an issue on my system but I just saw that pop up and I am wondering if my disk 2 is just cooked. 617 May 6 23:15:49 Hades kernel: ata1.00: exception Emask 0x50 SAct 0x0 SErr 0x280900 action 0x6 frozen May 6 23:15:49 Hades kernel: ata1.00: irq_stat 0x08000000, interface fatal error May 6 23:15:49 Hades kernel: ata1: SError: { UnrecovData HostInt 10B8B BadCRC } May 6 23:15:49 Hades kernel: ata1.00: failed command: READ DMA EXT May 6 23:15:49 Hades kernel: ata1.00: cmd 25/00:40:e0:be:5c/00:05:8c:01:00/e0 tag 10 dma 688128 in May 6 23:15:49 Hades kernel: res 50/00:00:df:be:5c/00:00:8c:01:00/ec Emask 0x50 (ATA bus error) May 6 23:15:49 Hades kernel: ata1.00: status: { DRDY } May 6 23:15:49 Hades kernel: ata1: hard resetting link May 6 23:15:49 Hades kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) May 6 23:15:49 Hades kernel: ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded May 6 23:15:49 Hades kernel: ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out May 6 23:15:49 Hades kernel: ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out May 6 23:15:49 Hades kernel: ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded May 6 23:15:49 Hades kernel: ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out May 6 23:15:49 Hades kernel: ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out May 6 23:15:49 Hades kernel: ata1.00: configured for UDMA/133 May 6 23:15:49 Hades kernel: ata1: EH complete

Why not install either the dolphin or krusader docker app, which gives you an interface similar to windows, but avoids the extra time involved via windows in moving everything back and forth over the network trying out dolphin now, this is definitely ideal over a windows app if it looks and works good

I know using straight windows explorer is a poor choice as its using the network to transfer a file from one spot to another (adding a TON of time). Normally I would just use command line but I need a graphical way to get my drives in a better space. I have 2 drives that are 99% full and a bunch of drives that are only 10-20% full. I want to move say 200GB-1000GB at a time but based on hundreds of specific folders in a share so it needs to be gui based.

I do... or well i have everything uber important to me backed up... IE Photos, Home Videos, Music. I also have all the important stuff backed up to CrashPlan as well, unfortunately CrashPlan is a memory hog and I was selective with backing up stuff since backing up 15TB to the cloud required about 16GB of RAM to do it... So again, Photos, Music and home videos only. I am dumb, just not completely stupid hahaha. Movies and TV Shows are a pain to recover but not an end of the world scenario. I just think there should be better wording on the format button especially in a catastrophic situation like that. Thankfully I do backup stuff that matters to me beyond unRAID, but still, not a good scenario. also, second parity drive is a plan (like you said probably not helpful in this scenario though), I was just planning to wait until 6.2 is official before getting it setup.

Am I to assume I should not use this drive anymore? Or should it be safe and just that partition for some reason become corrupt? 1000 was a bit high, I lost about 1000 movies and tv episodes, about 440 movies, but yes I am in the process of getting better quality stuff now, I have had my collection since about 2003 so I have a lot of Dvd rips still. I don't care about losing it, I care more about having no idea what was lost minus doing some fancy shit with Plex DBs to try to figure it out, oh and recovering tv shows sucks with Usenet.... As a side note to unRAID devs, might I recommend if something like this happens to at least have warning messages for dumb people like myself that formatting the drive will nuke everything in your parity from that drive as well. I knew that would happen somewhere in the back of my brain but typically when I have had drive failures the system acted accordingly and I knew what to do. This threw me for a loop and I acted quickly not smartly.

Ya, the format was dumb, but if the disc was dead why didn't my parity kick in? I've lost disks before, this was kind of frustrating beyond a doubt

in my system log: May 5 23:13:29 Hades kernel: XFS (md2): Internal error XFS_WANT_CORRUPTED_GOTO at line 3156 of file fs/xfs/libxfs/xfs_btree.c. Caller xfs_free_ag_extent+0x419/0x558 May 5 23:13:29 Hades kernel: CPU: 2 PID: 6733 Comm: mount Not tainted 4.4.6-unRAID #1 May 5 23:13:29 Hades kernel: Call Trace: May 5 23:13:29 Hades kernel: XFS (md2): Internal error xfs_trans_cancel at line 990 of file fs/xfs/xfs_trans.c. Caller xlog_recover_process_efi+0x148/0x155 May 5 23:13:29 Hades kernel: CPU: 2 PID: 6733 Comm: mount Not tainted 4.4.6-unRAID #1 May 5 23:13:29 Hades kernel: Call Trace: May 5 23:13:29 Hades kernel: XFS (md2): xfs_log_force: error -5 returned. May 5 23:13:29 Hades emhttp: mount error: No file system (32) hades-syslog-20160505-2336.zip

Is there anything I can do? I was browsing my NAS and all of a sudden disk 2 disappeared. I rebooted my NAS and it came up with disk 2 unmountable, format to continue. I formatted (probably a mistake, I assumed it would rebuilt my parity) and nothing, no more data... Prior to me reformatting my data was gone, I checked, 2500 movies down to 1500.... Is it hosed and how the heck did this happen? I am on 6.2 beta 21. My questions: 1. I am sure me selecting format was a bad choice but, why did it reboot and come back "healthy" and online yet definitely not since it was missing 2 TB of data? 2. Is there anything that can be done? Can I manually access the parity? can a parity be rebuilt or did I screw that up the minute I formatted the drive? I don't think so though since like I said, data was GONE prior to me hitting format. I wish I knew what was even on that drive... this is frustrating beyond belief and making me extremely worried to even turn on the server and lose more drives...

Nothing that I know of, I download and extract on my cache and push to my share. It started a few weeks ago and since turning off drone factory it hasn't happened again (albeit only a week of testing)

Do you use Sonarr? If so are you using Drone Factory or Completed Download Handling for the file renaming? I was having the same issue and for a long time I also thought it was NzbGet. I switched from using the Drone Factory to Completed Download Handling and I have not had this issue anymore. Thanks eroz, I changed that setting, hopefully it helps. So question to dev group, did you update any version of the base image in the last month or so? Apparently this is an issue with the version of Mono? https://forums.sonarr.tv/t/nzb-drone-post-processor-end-of-file-gets-cut-off-when-moving-across-network/963/27 I am just wondering because it worked fine for X number of months and then just started doing this out of the blue.

figure I would try here as well as NZBGet and my newshosting sites. for about 3 weeks now, I will download files and the video cuts out after about 30 minutes. NZBGet is showing the file fully downloads and uncompresses, but the uncompressed file is smaller than it should be. Watching the video in any player cuts out at the same point. So first thought was ovbiously the file/host but if I regrab the same file it gives all the same results (aka 100% download), but thee second or third time it is now the correct size and everything works fully. This was happening a solid 5-6 times a week and a week ago I thought it went away (despite it not mattering, or shouldn't, I saw my docker image was almost full so I recreated it and the issue seemed to go away for a week. It happened again yesterday. These files are coming from different sites and the files are verified working (2nd, 3rd or 4th time is the charm). Any ideas would be appreciated, I have no idea what is going on.

I decided to clear house because after rebooting all my dockers were stuck in "needs to update" but they couldn't update. EDIT: and I am an idiot, not sure why it was set to itself instead of my router 10.10.1.1.... but it has been like that for a couple years without issue.... I am 6.2b21 Sounds more like you need to set static DNS addresses in network settings sorry if this sounds dumb but my 5.x/6.x install has been set to automatic for a few years (my router is setup with a static IP), why would this change? last weekend I did a motherboard/cpu/ram swap, but even after that its been fine until today? Also, My DNS server settings have never changed, which i should clarify is set to my static ip (10.10.1.3)

is community applications down? i cant connect. I just cleared out my docker and all my plugin images and now I cant connect: browsing here works: tools.linuxserver.io I decided to clear house because after rebooting all my dockers were stuck in "needs to update" but they couldn't update. I am 6.2b21

In the next few weeks I plan to swap out my unraid servers mobo, cpu and ram (it's a 8gb amd Athlon) with an i7 16gb setup. What if any concerns should I have doing this, or will it truly be plug in play?

Anyone else not able to create a custom quality profile? I was able to before (as I have 3 that I made myself) but when I try adding a 4th it looks fine in the UI but once I refresh the page its gone. All other settings take effect, just not custom quality profiles.

I believe that the Plex Pass features is connected to your account and not specifically to a Plex Pass release. The Plex Pass releases is where all new features show up first so it’s more like a preview of new functionality that is implemented and an opportunity to find new bugs and “enjoy” them for a while before they get fixed. Yes you become the beta tester. Plex Pass is both beta testing/early release of features and premium features (such as Plex Home or Plex Sync to name a few). So Plex Pass matters if you use specific premium features, however it is as mentioned in this sense specific to just beta testing new releases. You will not lose any premium functionality being on the "official release" unless of course the premium functionality was just released and not in the official release thread yet. Your plex pass functionality is tied to your login and login only to Plex.

I've just been told we actually have a requests page "thingy" It's here... Good to know, I just put one in for the request I had a few posts above.

I haven a request for Plex Users, which is extremely helpful for media conversions automatically. This is built off of the CouchPotato/SickBeard/Sonarr plugin called SickBeard MP4 Autmator, https://github.com/mdhiggins/sickbeard_mp4_automator/blob/master/README.md, HOWEVER IT IS NOT IT. This is customized for Plex users to output not only better quality to be also add an AAC track to the beginning and also force the MOOV Atom to the beginning as well. The instructions for this version are below, found here if you are a plex forum member, https://forums.plex.tv/discussion/comment/931888/#Comment_931888: Pre-requisites: The only pre-requisite is to have python 2.7.9 installed. https://www.python.org/downloads/release/python-279/ Instructions for setup: 1. Download convert.zip from [ftp=ftp://ayars.tv]ftp://ayars.tv[/ftp] -- username and password are both guest Unzip, You will end up with [iNSTALLDIR]\Convert There are two directories (can be changed) inside this folder that are used for the media Process is where you put any files you want to convert Done is where the files will end up after processing You can run this multiple ways but the easiest is to use the Run.bat file. (or for this case setup a Cron Job maybe?) If you edit this file (run.bat) you will notice it's one line that reads: c:\python27\python manual.py -a -i c:\convert\process If you install python to a different folder then change the python directory at the beginning of this line. If you want to process files from a different location then c:\convert\process then just change this in the batch file. If you want to change the final location of where the final files are stored then edit autoProcess.ini (this is the file people will need to modify the most) file and change the output_directory setting. That's pretty much it. Put files in the process directory and run the batch file What this will do: It will process each and every file in the "process" directory. It will remux files that are h.264 and will transcode files that aren't h.264 video It will pull out any english subtitles and create SRT files from them. If you want to pull out other languages then modify the subtitle-language setting in the ini file. Multiple languages are supported by commas The completed file will not have subtitles (we pulled them out) It will clear all tags in the mp4 file so Plex doesn't pick up and use these tags instead of the proper meta-data It will create an AAC track as the first track upto 256K in size. It will remove all audio tracks not in english. If you want other languages included modify audio-language setting (ini file) and include any languages you want kept in the MP4 file. Multiple languages are supported by commas When it transcodes it wil use an h.264 profile of high; a level of 4.0; crf setting of 20. These are basically the same as Handbrake High Profile settings with a bit more refinement for Plex use that allows it to direct play more often. In all cases the final MP4 file has the MOOV ATOM at the beginning of the file (ie web optimized)