folic86
-
Posts
74 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Everything posted by folic86
-
I lost my cache. For some reason reinstalled Sonarr won't add files even if I refresh & scan, nor can it add files that are there after I try reimporting/re-adding a series! It does 1 or 2 episodes and some it just did the entire series for no obvious reason (all the below are 100% there)! They all live in the same share top level. I can manually map each episode, but that's it. Any advice welcome
-
Did a hard restart as it just wouldn't even connect remotely. It locked up when I tried to kill some containers for a few minutes. Finally ended, and got some proper diags - attached. Could you have a quick look, please? wopr-diagnostics-20240215-1824.zip
-
Thanks Jorge. It's weirdly been ok for ages and this just occurred so will look. I saw an NGIX proxy timeout page (500). Is it possible Swag could cause an issue? I installed an old set of templates when the cache died...
-
Managed to get a syslog if it helps! wopr-syslog-20240215-1644.zip
-
I think it might be mover, as it's apparently running, but there's nothing to move and it starts at 3am (so, 13hrs ago.) But I can't get it to reboot or shutdown in a clean way either
-
Hi guys, Can anyone suggest what the heck is causing my CPU load to hit 75%? I've not had this issue before but my cache drive died and I replaced it, so could it be that? I can't even download diags... it gets to "lsof -Pni 2>/dev/null|todos >'/wopr-diagnostics-20240215-1627/system/lsof.txt'" and just hangs! It's fine if I reboot, but it's happened twice now.
-
Also having this issue since updating
-
Not entirely sure that I have spares, so that may take a while. I'll be back.
-
When you say fix... replace? Because the breakout cable DIsk 1 & 2 was connected to was swapped last week when I had the same issue.... so could it be the power cable, or should I swap the drive so it connects to a different card?
-
Disk 11 says 199 UDMA CRC error count 0x003e200200000 Old age Always Never 6
-
Power issues? I added 3 drives and now think it was a bad idea! Which attribute? I don't really have the budget to replace it right now.....
-
Yeah it's currently mounted but I know if I reboot it will decide not to, as I had it last week. There are definitely splitters, and may well be more than 4 per cable, I'm not 100% sure.
-
Can anyone see what is causing the drive to fail? I've tried everything I can think of, and did an xfs repair, and it was fine for 2 days. It's driving me mad, as nothing is faulty, but if I reboot, it'll come up as unmountable. Would you zero the log? wopr-diagnostics-20230630-1728.zip
-
Thanks @Kilrah!
-
Hi guys, So I am thinking about using Included disk(s): and Excluded disk(s): for my shares, which already exist spread across all my drives. Is it possible to move files that already exist so the shares only sit on the included disks? I thought unBALANCE may be best but is there a better way?
-
Thanks - 2 of these would work right?
-
Thanks! Can Ijust swap out cards and replace? I am thinking of changing my HBA and adding a 2nd if my board has the slots - it may not.
-
What can I replace it with? Suggestions very welcome I've done memtest a lot - you always suggest that, but it's never showing me any errors.... so what gives?
-
Hi guys. My Drive 11 failed last week and I ran a SMART extended test, which showed no errors. I did a rebuild and it seemed fine - rebuild completed. It's then thrown me the same issue - 2048 read errors - so I assume SMART is missing something? I've attached the DIAGS but is it maybe a dodgy SATA cable or something more serious? wopr-diagnostics-20230426-1724.zip
-
So I did this, and it repaired the errors. I then had a lost+found folder which is fine but I embarked on a data rebuild and it has come back in an error state and has stopped the rebuild. I am so puzzled. Can you advise? wopr-diagnostics-20230124-1647.zip
-
Ok. Wil try, thanks Jorge!
-
I still have an unmountable Disk 9 though!
-
Thanks for the assistance Jorge. It found 0 errors when I ran it when this issue began. Does this info below help at all? How would RAM effect the log file issue? Also @JorgeB now I reset the stats and it says 0, do I just reboot and kill the corrupt log file and start again? What is your suggestion?
-
I've already done that. Didn't report any issues.
-
Diagnostics attachedwopr-diagnostics-20230120-1503.zip
