googleg

I have a problem in my list of stacks there is one line that only says "Failed to load <name of an old stack I removed>". I checked under /boot/config/plugins/compose.manager/projects there is one folder with the name of the old stack and it only contains one file "name" which contains the name of my old stack. Is it safe to delete that folder to remove the error message showing in the UI?

I am still running the version 2026.07.02. This thread gives my update anxiety.

Quick update: after changing my BIOS PWM settings from "automatic" to "software" now I have somewhat recover the control on both of my two fan. Somewhat because the fan that was previously not working is now stuck at 100%. Whatever I set as minimum PWM value in fan auto control is not reflected in the /sys/class/.../pwm3 which always read 255. I guess for now that will do, for sure full blast is better than nothing.

Hi all, Since my update to Unraid 7.2.7 I noticed that one of my two fans controlled by PWM, namely pwm3, is no longer working. I tried to force it with echo 1 > /sys/class/hwmon/hwmon4/pwm3_enable but the value keep reading 0. Am I the only one to see that behavior? Gemini told me to add the linux kernel parameter acpi_enforce_resources=lax , is this a possible solution?

I am curious, do you mind being a bit more specific regarding the issues you faced with 7.2.5?

Thanks.

Hi all, Ever since I built my NAS and made the mistake of formatting all 3 array disks in ZFS I have been suffering from very bad performances. Now I am in the middle of converting my disks from ZFS to BTRFS. I used the "empty disk" feature underf array operations. For 2 disks it went well but I am now stuck with my last disk. The mover ran for 36 hours and still has 120 GB to move out of the 2.5 TB initially present on that disk (of 4 TB). That's 18 MB per second on average... I think the mover is struggling to move a myriad of small files that are present on that disk. I don't really need those files so I'd like to stop the mover, delete the files and start again. Is there a recommended way to terminate the mover nicely, from the GUI or from the command line ? Thank you for your help.

Ok thanks. Yes in non-tabbed view the button is there, but not in the tabbed view. I am on 7.2.3

Ok I found out that in the settings the refresh interval was disable so I re-enabled it briefly and now it's all good. Is the manual refresh no longer possible?

Hello, I have migrated 2 disks in my array from ZFS to BTRFS but they still show in the ZFS Master view. The "update/refresh" button is not showing, what can I do to have the plugin register that two disks are no longer in ZFS?

Ok thank you. So I think time to migrate to BTRFS then. Wish me luck 🙏 😅

Is the white performance issue being worked on? I would risk going through the hassle of migrating my FS if a fix to the ZFS issue is about to be released...

Hi all, I am experiencing some slow transfer rates on my array which is made of 3 disks formatted as 3 x ZFS single disk pools. When copying a file from one disk to another the typical speed is around 80-100 MB/s, moving files between 2 datasets on the same disk I am at 40-50 MB/s. I chose ZFS because I need snapshots. My other alternative is to switch to BTRFS. Questions: is BTRS significantly faster than ZFS? Is there a written procedure somewhere to switch the filesystem of the array? Thanks a lot.

Hello all, Something I noticed in the UI is when I untick the box "write corrections to parity" under "array operations" and the I reload the page this settings will come back to "checked". Is there a way to disable it and make it to stick to that? Thank you.

Oops sorry what I was looking for was in fact right there under my nose: b38595ff52534922b927890317bed1061f5e113561f8d1d382acbf0da8eda547 That's my calibre web automated container, something went wrong with it.