Muff

64GB but I want to re-build my server with more Cores and RAM in the future

Cool, thank you! Is there any card you would recommend? I know HPs iLo has a license cost if you want more features.

Yes, I know. It was a bad example and I'll delete it. The beauty of Out-of-Band-Management is that you only need a network cable and you can access your server/PC over the network instead of using a KVM-switch. Here is an example of such card: Can I use it on an unRaid server?

Yes and I use that but what I'm after is the ability to connect to the server when it's powered off and the ability to see the boot screen. Like what you can do with HP iLo card.

Hi, Does unRaid support IPMI cards from example HP (iLo) and Dell (DRAC)? I've looked around but haven't found anything.

Hi, My unRaid server have been running great after I've upgrade from 6.3.5 (?) to 6.4.0 but yesterday I upgrade the BIOS on my MSI - Z270 XPOWER GAMING TITANIUM (MS-7A58) motherboard From: Version: 7A58v13 Release Date: 2017-07-24 To: Version: 7A58v14 Release Date: 2017-11-27 Source: https://www.msi.com/Motherboard/support/Z270-XPOWER-GAMING-TITANIUM#down-bios and at the same time I installed a heatsink on my M.2 disk (EK-M.2 NVMe Heatsink - Black) since unRaid keeped warning about its temprature. After this my unRaid server freezes after a short while when I start my array and it starts the Parity-Checks. The picture (Screen1.jpg) shows what I saw yesterday before I went to bed and it was still there now when I got home from work. Now I've rebooted the server and pulled the syslog & diagnostics files and tried again. Now I saw that it stopped at 1.2% (Parity-Checks) and the screen showed as in Screen2.jpg Any idé? Thank you! Screen1.jpg Screen2.jpg muff-syslog-20180202-1801-AfterReboot.txt muff-syslog-20180202-1744-BeforeReboot.txt Edit 1 I noticed that (sometimes) after a reboot my M.2 is missing sometimes and it comes back after another reboot. Edit 2 After I reseted the bios for the 2nd time and only enabled Intel-VT(?) and a couple reboot I got it to work again. But after all this I had to re-do my cache pool and all of my container and VMs were gone. I'll let it run over night and If I don't update this post, you can consider it "solved". Thank you and Cheers!

Maybe I should move this post to the VM Templates forum?

Ah, I didn't know what I was thinking when I grouped all my ports on both Source and Destination so I split them up now and it's working. Thank you!

Ah, it was under the Advanced Settings. I missed that. Thank you! And now I get this error: ------------------------------------- _ () | | ___ _ __ | | / __| | | / \ | | \__ \ | | | () | |_| |___/ |_| \__/ Brought to you by linuxserver.io We gratefully accept donations at: https://www.linuxserver.io/donations/ ------------------------------------- GID/UID ------------------------------------- User uid: 99 User gid: 100 ------------------------------------- [cont-init.d] 10-adduser: exited 0. [cont-init.d] 20-config: executing... [cont-init.d] 20-config: exited 0. [cont-init.d] 30-keygen: executing... using keys found in /config/keys [cont-init.d] 30-keygen: exited 0. [cont-init.d] 50-config: executing... DH parameters bit setting changed. Deleting old dhparams file. Creating DH parameters for additional security. This may take a very long time. There will be another message once this process is completed Generating DH parameters, 2048 bit long safe prime, generator 2 This is going to take a long time ....................................................................................................................+...............................................................................................................................+.......+.............................................................................................................+...........................................................................................................+.........................................................................................+..........................................................................................................................................................+.............................................................................................................................+........................................+....................................................................................................+...+...................................................................+...................................................................................................................................................................................+..................................................................................................................................................................................+.......................................................................+...............................................+...............................................................................+................................................................................................................+..................................................................................+.......................+...................................................................................................................................................................................................................................................................+...........................+.........................................................................................................+.................................................................................................+...............................................................................................................................................................+..........................+.............+......+..........+............................................................................................................................................................................................................+........................................................................................................+.....................................................................................................................+.............................+.............................................+....+...............................................................+............................................................................................+................+...................................................+........................................................................................................................................................+....................................................................+...................................+...+.....................................+..................................................................+.....+......................................+..................................................+.....................................................+........................................................................+..................................................................+......+..............................................................................................................................................................................................+......+......+....................................................................................................................................................................................................................................++*++* DH parameters successfully created - 2048 bits SUBDOMAINS entered, processing Only subdomains, no URL in cert Sub-domains processed are: -d webb.duckdns.org E-mail address entered: [email protected] Different sub/domains entered than what was used before. Revoking and deleting existing certificate, and an updated one will be created usage: certbot [SUBCOMMAND] [options] [-d DOMAIN] [-d DOMAIN] ... Certbot can obtain and install HTTPS/TLS/SSL certificates. By default, it will attempt to use a webserver both for obtaining and installing the certificate. certbot: error: argument --cert-path: No such file or directory Generating new certificate Saving debug log to /var/log/letsencrypt/letsencrypt.log Plugins selected: Authenticator standalone, Installer None Obtaining a new certificate Performing the following challenges: http-01 challenge for webb.duckdns.org Waiting for verification... Cleaning up challenges Failed authorization procedure. webb.duckdns.org (http-01): urn:acme:error:unauthorized :: The client lacks sufficient authorization :: Invalid response from http://webb.duckdns.org/.well-known/acme-challenge/RrOIRCumpKol_Q0gFd_-1NHrtiAdj9-v6CDTfn3eOVg: "<html> <head><title>404 Not Found</title></head> <body bgcolor="white"> <center><h1>404 Not Found</h1></center> <hr><center>" IMPORTANT NOTES: - The following errors were reported by the server: Domain: webb.duckdns.org Type: unauthorized Detail: Invalid response from http://webb.duckdns.org/.well-known/acme-challenge/RrOIRCumpKol_Q0gFd_-1NHrtiAdj9-v6CDTfn3eOVg: "<html> <head><title>404 Not Found</title></head> <body bgcolor="white"> <center><h1>404 Not Found</h1></center> <hr><center>" To fix these errors, please make sure that your domain name was entered correctly and the DNS A/AAAA record(s) for that domain contain(s) the right IP address. - Your account credentials have been saved in your Certbot configuration directory at /etc/letsencrypt. You should make a secure backup of this folder now. This configuration directory will also contain certificates and private keys obtained by Certbot so making regular backups of this folder is ideal. ERROR: Cert does not exist! Please see the validation error above. The issue may be due to incorrect dns or port forwarding settings. Please fix your settings and recreate the container And the pictures and from my Firewall (UniFi Security Gateway 3P) and the docker config

Hi, I ran unRAID v 6.3.4 and after I've upgraded it to 6.4.0 I started to see some strange things and one of those is that not one of my 4 VMs have Internet access (my containers have Internet access) and they had it before. This is the config for 3 of those VMs: Ubuntu 1 <domain type='kvm' id='6'> <name>Bitcoin 3</name> <uuid>dba27653-6af8-3d6d-be61-2bf09dc64f07</uuid> <metadata> <vmtemplate xmlns="unraid" name="Ubuntu" icon="ubuntu.png" os="ubuntu"/> </metadata> <memory unit='KiB'>1048576</memory> <currentMemory unit='KiB'>1048576</currentMemory> <memoryBacking> <nosharepages/> </memoryBacking> <vcpu placement='static'>2</vcpu> <cputune> <vcpupin vcpu='0' cpuset='3'/> <vcpupin vcpu='1' cpuset='7'/> </cputune> <resource> <partition>/machine</partition> </resource> <os> <type arch='x86_64' machine='pc-q35-2.7'>hvm</type> <loader readonly='yes' type='pflash'>/usr/share/qemu/ovmf-x64/OVMF_CODE-pure-efi.fd</loader> <nvram>/etc/libvirt/qemu/nvram/dba27653-6af8-3d6d-be61-2bf09dc64f07_VARS-pure-efi.fd</nvram> </os> <features> <acpi/> <apic/> </features> <cpu mode='host-passthrough' check='none'> <topology sockets='1' cores='1' threads='2'/> </cpu> <clock offset='utc'> <timer name='rtc' tickpolicy='catchup'/> <timer name='pit' tickpolicy='delay'/> <timer name='hpet' present='no'/> </clock> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/local/sbin/qemu</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='writeback'/> <source file='/mnt/user/VM Disk/Ubuntu 3/vdisk1.img'/> <backingStore/> <target dev='hdc' bus='virtio'/> <boot order='1'/> <alias name='virtio-disk2'/> <address type='pci' domain='0x0000' bus='0x03' slot='0x00' function='0x0'/> </disk> <controller type='usb' index='0' model='nec-xhci'> <alias name='usb'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </controller> <controller type='sata' index='0'> <alias name='ide'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x1f' function='0x2'/> </controller> <controller type='pci' index='0' model='pcie-root'> <alias name='pcie.0'/> </controller> <controller type='virtio-serial' index='0'> <alias name='virtio-serial0'/> <address type='pci' domain='0x0000' bus='0x02' slot='0x00' function='0x0'/> </controller> <controller type='pci' index='1' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='1' port='0x10'/> <alias name='pci.1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0' multifunction='on'/> </controller> <controller type='pci' index='2' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='2' port='0x11'/> <alias name='pci.2'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x1'/> </controller> <controller type='pci' index='3' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='3' port='0x12'/> <alias name='pci.3'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x2'/> </controller> <controller type='pci' index='4' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='4' port='0x13'/> <alias name='pci.4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x3'/> </controller> <controller type='pci' index='5' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='5' port='0x14'/> <alias name='pci.5'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x4'/> </controller> <interface type='bridge'> <mac address='52:54:00:9d:d7:16'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/0'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/0'> <source path='/dev/pts/0'/> <target type='serial' port='0'/> <alias name='serial0'/> </console> <channel type='unix'> <source mode='bind' path='/var/lib/libvirt/qemu/channel/target/domain-6-Bitcoin 3/org.qemu.guest_agent.0'/> <target type='virtio' name='org.qemu.guest_agent.0' state='disconnected'/> <alias name='channel0'/> <address type='virtio-serial' controller='0' bus='0' port='1'/> </channel> <input type='tablet' bus='usb'> <alias name='input0'/> <address type='usb' bus='0' port='1'/> </input> <input type='mouse' bus='ps2'> <alias name='input1'/> </input> <input type='keyboard' bus='ps2'> <alias name='input2'/> </input> <graphics type='vnc' port='5900' autoport='yes' websocket='5700' listen='0.0.0.0' keymap='sv'> <listen type='address' address='0.0.0.0'/> </graphics> <video> <model type='qxl' ram='65536' vram='65536' vgamem='16384' heads='1' primary='yes'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x04' slot='0x00' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='dac' relabel='yes'> <label>+0:+100</label> <imagelabel>+0:+100</imagelabel> </seclabel> </domain> ISCSI <domain type='kvm'> <name>ISCSI</name> <uuid>13b24101-eb6c-0aaa-a9ab-2034334f36ed</uuid> <metadata> <vmtemplate xmlns="unraid" name="CentOS" icon="centos.png" os="centos"/> </metadata> <memory unit='KiB'>4194304</memory> <currentMemory unit='KiB'>2097152</currentMemory> <memoryBacking> <nosharepages/> </memoryBacking> <vcpu placement='static'>2</vcpu> <cputune> <vcpupin vcpu='0' cpuset='0'/> <vcpupin vcpu='1' cpuset='4'/> </cputune> <os> <type arch='x86_64' machine='pc-q35-2.7'>hvm</type> </os> <features> <acpi/> <apic/> </features> <cpu mode='host-passthrough' check='none'> <topology sockets='1' cores='1' threads='2'/> </cpu> <clock offset='utc'> <timer name='rtc' tickpolicy='catchup'/> <timer name='pit' tickpolicy='delay'/> <timer name='hpet' present='no'/> </clock> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/local/sbin/qemu</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='writeback'/> <source file='/mnt/user/domains/ISCSI/vdisk1.img'/> <target dev='hdc' bus='sata'/> <boot order='1'/> <address type='drive' controller='0' bus='0' target='0' unit='2'/> </disk> <disk type='file' device='disk'> <driver name='qemu' type='qcow2' cache='writeback'/> <source file='/mnt/user/VM Disk/ISCSI/vdisk2.img'/> <target dev='hdd' bus='sata'/> <address type='drive' controller='0' bus='0' target='0' unit='3'/> </disk> <disk type='file' device='disk'> <driver name='qemu' type='qcow2' cache='writeback'/> <source file='/mnt/user/VM Disk/ISCSI/vdisk3.img'/> <target dev='hde' bus='sata'/> <address type='drive' controller='0' bus='0' target='0' unit='4'/> </disk> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='writeback'/> <source file='/mnt/user/VM Disk/ISCSI/vdisk4.img'/> <target dev='hdf' bus='sata'/> <address type='drive' controller='0' bus='0' target='0' unit='5'/> </disk> <disk type='file' device='disk'> <driver name='qemu' type='qcow2' cache='writeback'/> <source file='/mnt/user/VM Disk/ISCSI/vdisk5.img'/> <target dev='hdg' bus='sata'/> <address type='drive' controller='1' bus='0' target='0' unit='0'/> </disk> <controller type='usb' index='0' model='ich9-ehci1'> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x7'/> </controller> <controller type='usb' index='0' model='ich9-uhci1'> <master startport='0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0' multifunction='on'/> </controller> <controller type='usb' index='0' model='ich9-uhci2'> <master startport='2'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x1'/> </controller> <controller type='usb' index='0' model='ich9-uhci3'> <master startport='4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x2'/> </controller> <controller type='sata' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x1f' function='0x2'/> </controller> <controller type='sata' index='1'> <address type='pci' domain='0x0000' bus='0x03' slot='0x01' function='0x0'/> </controller> <controller type='pci' index='0' model='pcie-root'/> <controller type='pci' index='1' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='1' port='0x10'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0' multifunction='on'/> </controller> <controller type='pci' index='2' model='dmi-to-pci-bridge'> <model name='i82801b11-bridge'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x1e' function='0x0'/> </controller> <controller type='pci' index='3' model='pci-bridge'> <model name='pci-bridge'/> <target chassisNr='3'/> <address type='pci' domain='0x0000' bus='0x02' slot='0x00' function='0x0'/> </controller> <controller type='pci' index='4' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='4' port='0x11'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x1'/> </controller> <controller type='pci' index='5' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='5' port='0x12'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x2'/> </controller> <controller type='pci' index='6' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='6' port='0x13'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x3'/> </controller> <controller type='virtio-serial' index='0'> <address type='pci' domain='0x0000' bus='0x04' slot='0x00' function='0x0'/> </controller> <interface type='bridge'> <mac address='52:54:00:1a:95:90'/> <source bridge='br0'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <channel type='unix'> <target type='virtio' name='org.qemu.guest_agent.0'/> <address type='virtio-serial' controller='0' bus='0' port='1'/> </channel> <input type='tablet' bus='usb'> <address type='usb' bus='0' port='1'/> </input> <input type='mouse' bus='ps2'/> <input type='keyboard' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' websocket='-1' listen='0.0.0.0' keymap='sv'> <listen type='address' address='0.0.0.0'/> </graphics> <video> <model type='qxl' ram='65536' vram='65536' vgamem='16384' heads='1' primary='yes'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x0'/> </video> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x05' slot='0x00' function='0x0'/> </memballoon> </devices> </domain> W7-Tower <domain type='kvm'> <name>W7-Tower</name> <uuid>6bdb46b8-c791-5207-8f67-ff646eda6334</uuid> <metadata> <vmtemplate xmlns="unraid" name="Windows 7" icon="windows7.png" os="windows7"/> </metadata> <memory unit='KiB'>6815744</memory> <currentMemory unit='KiB'>4194304</currentMemory> <memoryBacking> <nosharepages/> </memoryBacking> <vcpu placement='static'>4</vcpu> <cputune> <vcpupin vcpu='0' cpuset='3'/> <vcpupin vcpu='1' cpuset='4'/> </cputune> <os> <type arch='x86_64' machine='pc-i440fx-2.7'>hvm</type> </os> <features> <acpi/> <apic/> <hyperv> <relaxed state='on'/> <vapic state='on'/> <spinlocks state='on' retries='8191'/> <vendor_id state='on' value='none'/> </hyperv> </features> <cpu mode='host-passthrough' check='none'> <topology sockets='1' cores='2' threads='2'/> </cpu> <clock offset='localtime'> <timer name='hypervclock' present='yes'/> <timer name='hpet' present='no'/> </clock> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/local/sbin/qemu</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='writeback'/> <source file='/mnt/user/domains/W7-Tower/vdisk1.img'/> <target dev='hdc' bus='virtio'/> <boot order='1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </disk> <controller type='usb' index='0' model='ich9-ehci1'> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x7'/> </controller> <controller type='usb' index='0' model='ich9-uhci1'> <master startport='0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0' multifunction='on'/> </controller> <controller type='usb' index='0' model='ich9-uhci2'> <master startport='2'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x1'/> </controller> <controller type='usb' index='0' model='ich9-uhci3'> <master startport='4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x2'/> </controller> <controller type='pci' index='0' model='pci-root'/> <controller type='virtio-serial' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </controller> <interface type='bridge'> <mac address='52:54:00:f6:38:7e'/> <source bridge='br0'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <channel type='unix'> <target type='virtio' name='org.qemu.guest_agent.0'/> <address type='virtio-serial' controller='0' bus='0' port='1'/> </channel> <input type='tablet' bus='usb'> <address type='usb' bus='0' port='1'/> </input> <input type='mouse' bus='ps2'/> <input type='keyboard' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' websocket='-1' listen='0.0.0.0' keymap='sv'> <listen type='address' address='0.0.0.0'/> </graphics> <video> <model type='qxl' ram='65536' vram='65536' vgamem='16384' heads='1' primary='yes'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <hostdev mode='subsystem' type='usb' managed='yes'> <source> <address bus='1' device='3'/> </source> <address type='usb' bus='0' port='3'/> </hostdev> <hostdev mode='subsystem' type='usb' managed='yes'> <source> <address bus='1' device='4'/> </source> <address type='usb' bus='0' port='2'/> </hostdev> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </memballoon> </devices> </domain> And the pictures are the network config on the unRAID server. Thank you!

How did you do that?

Hi, I've just upgrade my unRaid server from 6.3.4 (?) to 6.4.0 and since then my container letsencrypt isn't working as it used to. I've reinstalled the container and I still can't find the solution to the problem with some googleing The log: ------------------------------------- _ () | | ___ _ __ | | / __| | | / \ | | \__ \ | | | () | |_| |___/ |_| \__/ Brought to you by linuxserver.io We gratefully accept donations at: https://www.linuxserver.io/donations/ ------------------------------------- GID/UID ------------------------------------- User uid: 99 User gid: 100 ------------------------------------- [cont-init.d] 10-adduser: exited 0. [cont-init.d] 20-config: executing... [cont-init.d] 20-config: exited 0. [cont-init.d] 30-keygen: executing... using keys found in /config/keys [cont-init.d] 30-keygen: exited 0. [cont-init.d] 50-config: executing... DH parameters bit setting changed. Deleting old dhparams file. Creating DH parameters for additional security. This may take a very long time. There will be another message once this process is completed Generating DH parameters, 2048 bit long safe prime, generator 2 This is going to take a long time ..................................................................................................................................................................................................................................................................................................................................................................................................................................................................+......................................................................................................................+...+.........................................+...............................................................................................................................................+.......................................................................+...................................................+..................+.................................................................................+....................................................................+.................................................................................+..........................................................................................................+.+..................................................................................+..................................................................................................................................................................................+..........................................................+..........................................+.............................................................................................+..................................+................................................................................................................................................................................................+..............................................+.........................+.......................................................................................................+...................................................................................+.+........................................................+..........................................................................................+....................................+.......+............+...............................................................................................................................+.........................................................................................................................................................................................+.........+............................................+..........................................................+..+................................+........................................................................+....................................................................................+..................+..+...................................................................................................................................................................+......................................................................+..................................................................................................................................................................................................................................................................................................................................................................+.......................................................................+.......................................+..+.........................................+..................................+............................+............................................................+................................................................................................................................................................................+.+...............................................................................................................+.................................................+..............................................+...................+......................................................+.....................................................................................................................................................................................................+............................+.................................................................................+...........+......................................+........................................................................+...............................................................................................................................................................................................................................................................................................................................................................................................+.................................................................................+...........................................................................+................................................................................................................................................................................................................................................................................+....++*++* DH parameters successfully created - 2048 bits SUBDOMAINS entered, processing Only subdomains, no URL in cert Sub-domains processed are: -d domain.duckdns.org E-mail address entered: [email protected] Different sub/domains entered than what was used before. Revoking and deleting existing certificate, and an updated one will be created usage: certbot [SUBCOMMAND] [options] [-d DOMAIN] [-d DOMAIN] ... Certbot can obtain and install HTTPS/TLS/SSL certificates. By default, it will attempt to use a webserver both for obtaining and installing the certificate. certbot: error: argument --cert-path: No such file or directory Generating new certificate Saving debug log to /var/log/letsencrypt/letsencrypt.log Plugins selected: Authenticator standalone, Installer None Obtaining a new certificate Performing the following challenges: Client with the currently selected authenticator does not support any combination of challenges that will satisfy the CA. Client with the currently selected authenticator does not support any combination of challenges that will satisfy the CA. IMPORTANT NOTES: - Your account credentials have been saved in your Certbot configuration directory at /etc/letsencrypt. You should make a secure backup of this folder now. This configuration directory will also contain certificates and private keys obtained by Certbot so making regular backups of this folder is ideal. ERROR: Cert does not exist! Please see the validation error above. The issue may be due to incorrect dns or port forwarding settings. Please fix your settings and recreate the container The container config: Screenshot_1.jpg Thank you!

Ah, thank you!

Hi, I'm having some problem with renewal of my certificate and I haven't got the hang of all the part of a "certificate" and it's proces needed. When I SSH into my unRaid server the tool "certbot" doesn't exist and when I run "certtool" I got stuck on: root@Muff:/# certtool -u --load-ca-privkey="/mnt/user/appdata/letsencrypt/keys/cert.key" --load-ca-certificate="/mnt/user/appdata/letsencrypt/keys/cert.crt" Generating a signed certificate... missing --load-certificate root@Muff:/# I don't know where I can find "--load-certificate". And this is the log from the container: ------------------------------------- _ _ _ | |___| (_) ___ | / __| | |/ _ \ | \__ \ | | (_) | |_|___/ |_|\___/ |_| Brought to you by linuxserver.io We gratefully accept donations at: https://www.linuxserver.io/donations/ ------------------------------------- GID/UID ------------------------------------- User uid: 99 User gid: 100 ------------------------------------- [cont-init.d] 10-adduser: exited 0. [cont-init.d] 20-config: executing... [cont-init.d] 20-config: exited 0. [cont-init.d] 30-keygen: executing... using keys found in /config/keys [cont-init.d] 30-keygen: exited 0. [cont-init.d] 50-config: executing... 4096 bit DH parameters present SUBDOMAINS entered, processing Only subdomains, no URL in cert Sub-domains processed are: -d secret.duckdns.org E-mail address entered: [email protected] <-------------------------------------------------> <-------------------------------------------------> cronjob running on Thu Nov 23 16:23:28 CET 2017 Running certbot renew Saving debug log to /var/log/letsencrypt/letsencrypt.log ------------------------------------------------------------------------------- Processing /etc/letsencrypt/renewal/secret.duckdns.org.conf ------------------------------------------------------------------------------- Cert is due for renewal, auto-renewing... Running pre-hook command: s6-svc -d /var/run/s6/services/nginx Hook command "s6-svc -d /var/run/s6/services/nginx" returned error code 111 Error output from s6-svc: s6-svc: fatal: unable to control /var/run/s6/services/nginx: No such file or directory Renewing an existing certificate Performing the following challenges: tls-sni-01 challenge for secret.duckdns.org Waiting for verification... Cleaning up challenges Attempting to renew cert from /etc/letsencrypt/renewal/secret.duckdns.org.conf produced an unexpected error: Failed authorization procedure. cizco.duckdns.org (tls-sni-01): urn:acme:error:connection :: The server could not connect to the client to verify the domain :: Timeout. Skipping. Running post-hook command: s6-svc -u /var/run/s6/services/nginx ; cd /config/keys/letsencrypt && openssl pkcs12 -export -out privkey.pfx -inkey privkey.pem -in cert.pem -certfile chain.pem -passout pass: Error output from s6-svc: s6-svc: fatal: unable to control /var/run/s6/services/nginx: No such file or directory All renewal attempts failed. The following certs could not be renewed: /etc/letsencrypt/live/secret.duckdns.org/fullchain.pem (failure) 1 renew failure(s), 0 parse failure(s) IMPORTANT NOTES: - The following errors were reported by the server: Domain: secret.duckdns.org Type: connection Detail: Timeout To fix these errors, please make sure that your domain name was entered correctly and the DNS A record(s) for that domain contain(s) the right IP address. Additionally, please check that your computer has a publicly routable IP address and that no firewalls are preventing the server from communicating with the client. If you're using the webroot plugin, you should also verify that you are serving files from the webroot path you provided. [cont-init.d] 50-config: exited 0. [cont-init.d] done. [services.d] starting services [services.d] done. Server ready DuckDNS.org has the correct WAN IP and it gets it's update from my router (ubnt UniFi Security Gateway 3P). Thank you!

Hi, Thank you! The error seems to have disappeared and I've removed the port opening for 22 since I won't be using SFTP over the internet for now.

Hi, I just got notified from Fix Common Problems that I have problem/problems with call traces and that I should be posting it here. Not sure what it means since I haven't seen any problem yet with my unraid server. I hope you can help med and thank you in advance Cheers, muff-diagnostics-20171009-1751.zip

It seems to have worked... 1, I disabled Intel VT-D 2, Start the array and let it rebuild. 3, Enable Intel VT-D 4, Start the array Really strange... Thank you all for you help!

This is what I got in the morning: I've made a ticket to the unRaid support

Hi, Yes, I did that but it behaved the same. Right now I've changed the parity disk with the new HDD (from 4TB to 6TB) and it's reconstructing the array as we speak. It's at 3.2% but I'm now sure if it "broke" now or not. It sep 25 22:50 and the last entry in the Log was: Sep 25 22:01:43 Muff kernel: BUG: unable to handle kernel NULL pointer dereference at 0000000000000048 Sep 25 22:01:43 Muff kernel: IP: [<ffffffff81382a02>] generic_make_request_checks+0x31d/0x358 Sep 25 22:01:43 Muff kernel: PGD 0 Sep 25 22:01:43 Muff kernel: Sep 25 22:01:43 Muff kernel: Oops: 0000 [#3] PREEMPT SMP Sep 25 22:01:43 Muff kernel: Modules linked in: md_mod bonding e1000e igb ptp pps_core i2c_algo_bit mxm_wmi x86_pkg_temp_thermal coretemp kvm_intel i2c_i801 ahci i2c_smbus kvm i2c_core libahci cdc_acm video wmi backlight [last unloaded: md_mod] Sep 25 22:01:43 Muff kernel: CPU: 2 PID: 11788 Comm: unraidd Tainted: G D 4.9.30-unRAID #1 Sep 25 22:01:43 Muff kernel: Hardware name: MSI MS-7A58/Z270 XPOWER GAMING TITANIUM (MS-7A58), BIOS 1.30 07/04/2017 Sep 25 22:01:43 Muff kernel: task: ffff88102776a7c0 task.stack: ffffc900083ac000 Sep 25 22:01:43 Muff kernel: RIP: 0010:[<ffffffff81382a02>] [<ffffffff81382a02>] generic_make_request_checks+0x31d/0x358 Sep 25 22:01:43 Muff kernel: RSP: 0000:ffffc900083afcb8 EFLAGS: 00010206 Sep 25 22:01:43 Muff kernel: RAX: 0000000000000008 RBX: ffff880ff805d4d8 RCX: 0000000000000008 Sep 25 22:01:43 Muff kernel: RDX: ffff88102dc297a0 RSI: ffff880ff807e000 RDI: ffff88100b569d40 Sep 25 22:01:43 Muff kernel: RBP: ffffc900083afd00 R08: 000000000000000a R09: 0000000000000002 Sep 25 22:01:43 Muff kernel: R10: ffffc900083afd68 R11: 0000000000002800 R12: ffff880ff805d4d8 Sep 25 22:01:43 Muff kernel: R13: ffff8810146e0000 R14: ffff880ff805d4d8 R15: ffff881025515168 Sep 25 22:01:43 Muff kernel: FS: 0000000000000000(0000) GS:ffff88106ec80000(0000) knlGS:0000000000000000 Sep 25 22:01:43 Muff kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Sep 25 22:01:43 Muff kernel: CR2: 0000000000000048 CR3: 0000000001c09000 CR4: 00000000003406e0 Sep 25 22:01:43 Muff kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Sep 25 22:01:43 Muff kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Sep 25 22:01:43 Muff kernel: Stack: Sep 25 22:01:43 Muff kernel: ffffffff8137e3e4 ffff880ff805d1f0 0000000000000002 ffff880ff807e000 Sep 25 22:01:43 Muff kernel: ffff880ff805d4d8 0000000000000002 00000000ffffffff ffff880ff805d4d8 Sep 25 22:01:43 Muff kernel: ffff881025515168 ffffc900083afd50 ffffffff81383e03 0000000100000000 Sep 25 22:01:43 Muff kernel: Call Trace: Sep 25 22:01:43 Muff kernel: [<ffffffff8137e3e4>] ? xor_avx_2+0x1b9/0x1c0 Sep 25 22:01:43 Muff kernel: [<ffffffff81383e03>] generic_make_request+0x28/0x21b Sep 25 22:01:43 Muff kernel: [<ffffffffa003d68a>] handle_stripe+0x10b9/0x1229 [md_mod] Sep 25 22:01:43 Muff kernel: [<ffffffffa003d68a>] ? handle_stripe+0x10b9/0x1229 [md_mod] Sep 25 22:01:43 Muff kernel: [<ffffffff8107409b>] ? put_prev_entity+0x39/0x5f0 Sep 25 22:01:43 Muff kernel: [<ffffffffa003d8a9>] unraidd+0xaf/0xff [md_mod] Sep 25 22:01:43 Muff kernel: [<ffffffffa0038189>] md_thread+0xbb/0xcf [md_mod] Sep 25 22:01:43 Muff kernel: [<ffffffffa0038189>] ? md_thread+0xbb/0xcf [md_mod] Sep 25 22:01:43 Muff kernel: [<ffffffff8107c0fd>] ? wake_up_bit+0x25/0x25 Sep 25 22:01:43 Muff kernel: [<ffffffffa00380ce>] ? md_open+0x31/0x31 [md_mod] Sep 25 22:01:43 Muff kernel: [<ffffffff81063939>] kthread+0xdb/0xe3 Sep 25 22:01:43 Muff kernel: [<ffffffff8106385e>] ? kthread_park+0x52/0x52 Sep 25 22:01:43 Muff kernel: [<ffffffff8167f785>] ret_from_fork+0x25/0x30 Sep 25 22:01:43 Muff kernel: Code: e4 08 48 0f 44 fb e8 75 6b 04 00 e8 47 80 d0 ff 44 88 f0 83 f0 01 eb 3f b8 a1 ff ff ff e9 9a fd ff ff 49 8b 54 24 08 48 8b 52 08 <48> 8b 52 48 48 c1 fa 09 0f 84 5c fd ff ff 89 c1 48 39 ca 0f 82 Sep 25 22:01:43 Muff kernel: RIP [<ffffffff81382a02>] generic_make_request_checks+0x31d/0x358 Sep 25 22:01:43 Muff kernel: RSP <ffffc900083afcb8> Sep 25 22:01:43 Muff kernel: CR2: 0000000000000048 Sep 25 22:01:43 Muff kernel: ---[ end trace b4ba5be2a4aa8a6f ]--- I'm thinking of leaving it under the night.

Hi, After a shutdown, added a new HDD my unRaid server and enabled "Intel VT-D Tech" in BIOS it won't start my array. It freezes/restarts when it does a Parity-Check for around 10min. I ran a Pre-Clear on the new HDD for 1h and that worked. I can start the array in Maintenance Mode but as soon as I run a Parity-Check it freezes/restarts. It doesn't matter if I start unRaid in Safe Mode or not. Any advice? Thank you!

Hi, I suppose you are talking about this guide? https://www.linuxserver.io/2016/07/28/installing-nextcloud-on-unraid/ https://www.linuxserver.io/2017/05/10/installing-nextcloud-on-unraid-with-letsencrypt-reverse-proxy/ I just got NextCloud working. I forgot this part: Changing the default file of nextcloud I thank everyone who helped me with this

Hi everyone! I'm trying to configure forwarding for some dockers on my unRaid server but I get 502 Bad Gateway on 3 of my sites and the last I get a blank page: I've been folloing the following guid: https://cyanlabs.net/tutorials/the-complete-unraid-reverse-proxy-duck-dns-dynamic-dns-and-letsencrypt-guide/ This is my config (Path: /mnt/user/appdata/letsencrypt/nginx/site-confs): Please see default.txt And this is my config.php file in /mnt/user/appdata/nextcloud/www/nextcloud/config : Please see config.txt I've been sitting with this for awhile and in need of a new fresh pair of eyes Thank you! default.txt config.txt

Yes, that is correct. This is a minor issue since I can access it via plex.tv so don't put so much time and energy into it

Yes and I haven't configured any vlans

Hi, I'm in need of a little help with Plex and I hope that you can help me I'm not sure why but for some reason I can't access my Plex server locally (via plex.tv works) and I get the following error: Chrome on port 32400: ERR_EMPTY_RESPONSE Chrome on port 32401: ERR_CONNECTION_REFUSED Firefox on port 32400: Unable to connect Firefox on port 32401: The connection was reset The Plex Log: ------------------------------------- _ _ _ | |___| (_) ___ | / __| | |/ _ \ | \__ \ | | (_) | |_|___/ |_|\___/ |_| Brought to you by linuxserver.io We gratefully accept donations at: https://www.linuxserver.io/donations/ ------------------------------------- GID/UID ------------------------------------- User uid: 99 User gid: 100 ------------------------------------- [cont-init.d] 10-adduser: exited 0. [cont-init.d] 30-dbus: executing... [cont-init.d] 30-dbus: exited 0. [cont-init.d] 40-chown-files: executing... [cont-init.d] 40-chown-files: exited 0. [cont-init.d] 50-plex-update: executing... Atempting to upgrade to: 1.9.0.4252-d07c1f408 2017-09-14 09:40:06 URL:https://downloads.plex.tv/plex-media-server/1.9.0.4252-d07c1f408/plexmediaserver_1.9.0.4252-d07c1f408_amd64.deb [107649162/107649162] -> "/tmp/plexmediaserver_1.9.0.4252-d07c1f408_amd64.deb" [1] (Reading database ... 11381 files and directories currently installed.) Preparing to unpack .../plexmediaserver_1.9.0.4252-d07c1f408_amd64.deb ... Unpacking plexmediaserver (1.9.0.4252-d07c1f408) over (1.8.4.4249-3497d6779) ... Setting up plexmediaserver (1.9.0.4252-d07c1f408) ... ################################################################## # NOTE: Your system does not have udev installed. Without udev # # you won't be able to use DVBLogic's TVButler for DVR # # or for LiveTV # # # # Please install udev and reinstall Plex Media Server to # # to enable TV Butler support in Plex Media Server. # # # # To install udev run: sudo apt-get install udev # # # ################################################################## Processing triggers for systemd (229-4ubuntu19) ... [cont-init.d] 50-plex-update: exited 0. [cont-init.d] done. [services.d] starting services Starting Plex Media Server. Starting dbus-daemon [services.d] done. dbus[299]: [system] org.freedesktop.DBus.Error.AccessDenied: Failed to set fd limit to 65536: Operation not permitted Starting Avahi daemon Found user 'avahi' (UID 106) and group 'avahi' (GID 107). Successfully dropped root privileges. avahi-daemon 0.6.32-rc starting up. No service file found in /etc/avahi/services. *** WARNING: Detected another IPv4 mDNS stack running on this host. This makes mDNS unreliable and is thus not recommended. *** socket() failed: Address family not supported by protocol Failed to create IPv6 socket, proceeding in IPv4 only mode socket() failed: Address family not supported by protocol Joining mDNS multicast group on interface virbr0.IPv4 with address 192.168.122.1. New relevant interface virbr0.IPv4 for mDNS. Joining mDNS multicast group on interface docker0.IPv4 with address 172.17.0.1. New relevant interface docker0.IPv4 for mDNS. Joining mDNS multicast group on interface br0.IPv4 with address 192.168.1.17. New relevant interface br0.IPv4 for mDNS. Network interface enumeration completed. Registering new address record for 192.168.122.1 on virbr0.IPv4. Registering new address record for 172.17.0.1 on docker0.IPv4. Registering new address record for 192.168.1.17 on br0.IPv4. Server startup complete. Host name is Muff.local. Local service cookie is 1670098298. I've also setup apache docker so I can access my docker container via Internet. Is this normal or should I be able to access my Plex server via the LAN address? Thank you!