• Posts

  • Joined

  • Last visited

Everything posted by Tweak3D

  1. I've got 2 questions/issues. Firstly, While the UI is loading, it constantly prompts for credentials and complains about not being able to connect to rclone. I checked the UI log and its stating the following: 2022/09/27 09:02:58 INFO : Using --user admin --pass XXXX as authenticated user 2022/09/27 09:02:58 NOTICE: Serving remote control on 2022/09/27 09:02:58 NOTICE: Web GUI is not automatically opening browser. Navigate to http://admin:PASSWORDREMOVED@ to use. XXXX is not my password obviously, but my password is showing in the line below stating "Web GUI is not automatically opening browser." if I copy that URL it logs in and works just fine, but why is it not working directly from the Unraid UI? Secondly, I have a few shares with spaces in the name, for Example /mnt/user/appdata backup. But I am having issues getting the docker to see these as Media Shares. I've tried the following: /media/appdata backup /media/'appdata backup' '/media/'appdata backup'' '/media/appdata backup' /media/'appdata\ backup' /media/appdata\ backup All yield the same result, folder not found. How do I deal with handling a folder space in the path name for this docker? Thanks!
  2. I've been seeing some similar but not identical issues on my box as well. Motherboard is an Asus z690-P D4. Errors are mostly: ACPI BIOS Error (bug): Failure creating named object [\_SB.PC00.PEG1.PEGP._DSM.USRG], AE_ALREADY_EXISTS (20210730/dsfield-184) and there are tons of them. Additionally, I'm pretty sure unraid is trying to reboot, but it often stalls part way through leaving unraid inaccessible. When I turn on the monitor connected to unraid, all I see is a black screen. Performing a hard reboot is the only way to bring it back and then it reports all is good minus the errors mentioned above. Some research is showing this could be linux kernal/bios issue or an nviida driver issue. being that i'm on 12th gen intel and nvidia platform, both seem like they could be related in my situation
  3. I have 2 servers, one came up without issue, but my other was the same. In my case, for some reason the USB wasn't being detected in the bios any longer. It wasn't corrupt, but did require me to pull the USB drive and reconnect it in order to get it to be detected. Hard shutdown and power on didn't have any impact.
  4. I've only ever seen it on forced shutdowns previously. My config is mostly unchanged for the last several revisions of unraid. I only stopped looking into it as others reported the same issue and most said it was likely a bug. I see now that it was also called out for those of us impacted that the logs were showing that the system wasn't waiting for the disks to shut down properly, and by toggling the field for disk timeout, this seemed to correct it (Post for reference: Parity check running when starting array every time - General Support - Unraid) and that seems to have corrected the issue for me as well. I changed the value to 100, saved, changed it back to 90 (what it was previously) and it looks like i'm good to go now. Hopefully this helps if others are having the same issue.
  5. I've been having this issue since 6.9.1 where a reboot or a shutdown causes unraid to force a parity check when it comes back online. I saw that lots of others (but not everyone) were having this issue. Just reporting that this does not appear to be fixed in 6.9.2 :(. If there are any details I can provide to help get it fixed, i'd be more than happy to!
  6. spoke too soon, found the issue. Cache Directories was causing the issue even in safe mode oddly enough. I noted an error referencing the old drives share and removed it and now it formatted as expected.
  7. no luck, same result :(. I may pull the drive and wipe it on a separate machine and then reinstall and let unraid do its thing again and see if that makes any difference unless you have anything else I can check
  8. I moved a drive from unassigned devices that I was no longer using to my array as i needed some additional space urgently. The drive precleared without issue and i've tried twice now to format the drive on the array and it claims it starts, but the unraid GUI gets stuck in a funny state (can't look at logs, it claims the array isn't started, but it is, no stats update) and it just never formats the drive. I can reboot and everything goes back to normal, but the drive still isn't formatted. Not sure how else to proceed. I've attached my diag, but I don't see anything in the logs that i'm familiar with that indicate what the issue. The disk i'm adding is disk 13. also, I am currently running 6.8.2. Thanks for any assistance/guidance anyone can provide.
  9. Good morning, Just wanting to confirm something before I move forward and cause myself pain. I need to add a new drive and would like to also upgrade an existing drive. Can I do this in one motion (shutdown, add the new drive, replace the old drive, restart unraid with the array stopped, update the drive assignments and let it do its thing)? I am running a 2 drive parity, but would prefer to not be in an unsafe state during this upgrade, so thats why i'm checking here first. Since both new drives need to pre-clear first, I imagine that if I don't preclear on my own, both drives will do the mandatory 1 pass pre-clear and only the existing disk will require using the parity while that and the drive rebuild occurs. Is that correct? If I am incorrect here, no issues, I can run the add disk first and then upgrade disk separately, just trying to save some time as we all this process can take a while. thanks!
  10. I got my instance up and running behind my proxy and it works great. Also confirming that by adding that variable to my template manually, it works perfectly! just be aware that the value of "false" is case sensitive, so keep it all lower case and name the variable with the name from the documentation and it works as expected.
  11. I've been fighting the same issue for weeks, but didn't realize Chrome was to blame. Tried IE11 and sure enough works without issue. i can also connect via the mobile app without issue, so something is definitely up. also, interestingly enough, the Bitwarden addin for Chrome works fine, just not the web interface.
  12. So just to follow up, Bitwarden is now loading and I can get to the login and create account screen, but hitting the submit button doesn't work when the form is filled out. I can cancel without issue and if I leave a required field blank it prompts me saying to fill in the corresponding empty fields. I've deleted and recreated the container, the docker image, and deleted my appdata/bitwarden directory. I don't see any errors in the docker container log at all anymore, but I don't know where else I can look for logging as I am unfamiliar with this docker. Any assistance would be much appreciated. Thanks!
  13. ok, I deleted what I had, disabled direct i/o and it is installing now without issue, but now I cannot register an account, I get to the page, fill it out and click submit and nothing happens. Browser doesn't even indicate that anything is occuring. No errors or anything. So thats kinda odd. Any thoughts on that?
  14. its ok, I apprecaite the help. I ended up copying the file db.sqllite3 from the bit warden directory on my UD to the appdata folder and overwrote what it had tried to made. I then remapped the docker to point back and my cache drives and now it works fine. I'll do some more testing, but super odd issue.
  15. New directory on cache pool does not work. New directory on UD works fine as XFS and/or BRTFS I checked the perms on the Cache disk and that doesn't make a difference. I manually ran moved and moved off several hundred gigs of data to free up so blocks in a different part of the SSD, same issue. FS check in maintenance mode came up clean BTRFS scrube came up clean. both short and long SMART Tests passed without issue. No other errors in any other dockers, VMs, or unraid that I can see So it is something with my cache pool. but not exactly sure what. Any other suggestions I can try before I start updating firmware?
  16. It could, but i'm not seeing any other issues with anything else. Nothing in the logs, smart tests, etc. I have dual Enterprise Intel p3600 1.6tb SSDs as my cache drive where this is running. I guess I can run a check on the FS on those 2 disks, but i'd think that an error of this nature would come up in various places and not with one very specific docker image. I'm fairly new to troubleshooting docker issues though, so it could very well be. I'll take a look.
  17. I cannot get bitwarden to load at all. I've deleted and reinstalled multiple times and i'm only using default settings, so not sure what exactly is going on. Any assistance would be much apprecaited. The Docker never starts and this is all I see in the logs: First run: JWT keys don't exist, checking if OpenSSL is available...OpenSSL detected, creating keys...Keys created correctly.thread 'main' panicked at 'Can't run migrations: QueryError(DatabaseError(__Unknown, "disk I/O error"))', libcore/ Run with `RUST_BACKTRACE=1` for a backtrace. Subsequent Runs: thread 'main' panicked at 'Failed to turn on WAL: DatabaseError(__Unknown, "disk I/O error")', libcore/ Run with `RUST_BACKTRACE=1` for a backtrace.thread 'main' panicked at 'Failed to turn on WAL: DatabaseError(__Unknown, "disk I/O error")', libcore/ Run with `RUST_BACKTRACE=1` for a backtrace.thread 'main' panicked at 'Failed to turn on WAL: DatabaseError(__Unknown, "disk I/O error")', libcore/ Run with `RUST_BACKTRACE=1` for a backtrace.
  18. Anyone? Performance is back to normal after mover stopped. Dockers themselves don't seem to be impacted, but they are also very slow when accessing the array. Seems to be worst when the files being moved by mover are very small, like in my attached logs, where you can see it moving the plex appdata back to my new cache drive from the array. Seems very odd, but could really use some assistance in troubleshooting as i'm not seeing much info out there.
  19. nm, update the original post, you were right, I had misclicked the file. New one is attached. hoofs-diagnostics-20180621-1608 (1).zip
  20. When mover is running, my system goes to a crawl. For instance, loading the dashboard takes about 15 seconds, changing to any other tab about the same amount of time. Accessing any shares regardless of location is also very very slow. My system is no slouch, so i'm not quite sure why this is occuring as i'm not remotely close to maxing out any of my systems specs: 2x Intel E5-2420v2 96gb DDR3 1600 ECC triple channel 1.6tb Intel P3600 NVME PCIE x4 Cache drive 3x 8tb WD Red Parity and Data drives 6x 3tb WD Red Data drives 3tb WD Red Unassigned Device everything is perfect when mover isn't working, but slows to a crawl. This occurs with no dockers or vm's running. What/where can I check to see whats going on with this? I've attached the diags from while mover had been running for a while and the UI being very unresponsive. hoofs-diagnostics-20180621-1608 (1).zip
  21. wanted to add an example. Copying some large files from my computer to the array and copying files from an unassigned disk to my computer. Either copy alone will saturate the gigabit nic no problem, but with both going, they both drop to 10 mb/s or less and very often both go to 0 for a bit and then bounce back up to 10ish. If I pause either copy, within seconds the other copy jumps back to saturating the nic. During the time that both are slow, the entire array and and any apps are slow from every device on my network. Perhaps its a networking issue?
  22. I've been more heavily utilizing my unraid setup recently and loading lots of media onto my array while also utilizing dockers and the webgui within the system. I've been running into a lot of lag though whenever a few things start happening at once, but I cannot pin down the cause. Based on my observations, i think this is related to my Cache disk not being able to keep up but wanted to get some ideas of where to check as i'm not that familiar with non-windows os's. So, first off, my hardware Lenovo TD340 2x Intel E5-2420V2 96gb DDR3 ECC 1600 ram 5x 3TB WD Red Data Drives 3x 8Tb WD Red Data drives 512gb Samsung 850 Pro Cache Drive 256gb Samsung 850 Pro Unassigned (Plex DB) I'm running the SSD's through the motherboard SATA connectors and the harddrives are driven through an IT mode raid controller. So my primary issue is say i'm copying down a lot of large media thats going to take some time. but if plex or sickrage decide to also go out and update their DB, basically unraid becomes a slide show and is nearly unusable until i can get in and stop one of the outstanding tasks. I am not, however seeing any significant usage on my CPU or memory, so unless the items causing me pain are all single threaded, i'm at a loss. Where can I start looking to help diagnose this performance? I am considering replacing my SSD's with an m.2 (970 pro likely), but don't want to unless I am able to confirm its the iops limiting me currently. Things I've tried so far: Moving plex to its own SSD Moving deluge to its own dedicated unassigned drive Moving my surveillance (unifi) to its own dedicated harddrive. While the above help, none have made the problem go away. Any thoughts?
  23. gave this a try and got the same results. Just using PIA, so not sure why its not working here, seems to work fine on my desktop using their client: 2016-11-22 08:15:02,220 DEBG 'deluge-script' stderr output: [2016-11-22 08:15:02.220] Saved "/config/torrents/ubuntu-16.10-desktop-amd64.iso.0403fb4728bd788f.torrent" (variant.c:1266) [2016-11-22 08:15:02.220] ubuntu-16.10-desktop-amd64.iso Queued for verification (verify.c:269) [2016-11-22 08:15:02.220] ubuntu-16.10-desktop-amd64.iso Verifying torrent (verify.c:224) 2016-11-22 08:15:03,220 DEBG 'deluge-script' stderr output: [2016-11-22 08:15:03.220] ubuntu-16.10-desktop-amd64.iso Could not connect to tracker (announcer.c:996) [2016-11-22 08:15:03.220] ubuntu-16.10-desktop-amd64.iso Retrying announce in 20 seconds. (announcer.c:1005)
  24. Having an issue and haven't see a solution. I added the docker, added my VPN info, all appears fine, but I constantly get warnings about "Cannot connect to tracker". Example below. Removed the name of the torrent and replaced with ****. [2016-11-21 12:33:01.295] **** Retrying announce in 1809 seconds. (announcer.c:1005) [2016-11-21 12:33:01.295] **** Connection failed (announcer.c:996) after several attempts, I then get this error: 2016-11-21 12:25:31,294 DEBG 'deluge-script' stderr output: [2016-11-21 12:25:31.294] **** Scrape error: Could not connect to tracker (announcer.c:1279) The log before it starts trying to download looks find to me, no warnings or errors, but I am horrible with routing, so perhaps something is off. usermod: no changes [info] Env var PUID defined as 99 [info] Env var PGID defined as 100 [info] Permissions already set for /config [info] Starting Supervisor... 2016-11-21 12:24:09,905 CRIT Set uid to user 0 2016-11-21 12:24:09,905 WARN Included extra file "/etc/supervisor/conf.d/delugevpn.conf" during parsing 2016-11-21 12:24:09,909 INFO supervisord started with pid 27 2016-11-21 12:24:10,912 INFO spawned: 'start-script' with pid 30 2016-11-21 12:24:10,913 INFO spawned: 'deluge-script' with pid 31 2016-11-21 12:24:10,915 INFO spawned: 'privoxy-script' with pid 32 2016-11-21 12:24:10,922 DEBG 'deluge-script' stdout output: [info] VPN is enabled, checking VPN tunnel local ip is valid 2016-11-21 12:24:10,922 INFO success: start-script entered RUNNING state, process has stayed up for > than 0 seconds (startsecs) 2016-11-21 12:24:10,922 INFO success: deluge-script entered RUNNING state, process has stayed up for > than 0 seconds (startsecs) 2016-11-21 12:24:10,922 INFO success: privoxy-script entered RUNNING state, process has stayed up for > than 0 seconds (startsecs) 2016-11-21 12:24:10,925 DEBG 'start-script' stdout output: [info] VPN is enabled, beginning configuration of VPN 2016-11-21 12:24:10,926 DEBG 'privoxy-script' stdout output: [info] VPN is enabled, checking VPN tunnel local ip is valid 2016-11-21 12:24:10,935 DEBG 'start-script' stdout output: [info] VPN provider defined as pia [info] VPN config file (ovpn extension) is located at /config/openvpn/openvpn.ovpn 2016-11-21 12:24:10,937 DEBG 'start-script' stdout output: [info] Env vars defined via docker -e flags for remote host, port and protocol, writing values to ovpn file... 2016-11-21 12:24:10,954 DEBG 'start-script' stdout output: [info] VPN provider remote gateway defined as [info] VPN provider remote port defined as 1198 [info] VPN provider remote protocol defined as udp 2016-11-21 12:24:10,961 DEBG 'start-script' stdout output: [info] VPN provider username defined as **** 2016-11-21 12:24:10,970 DEBG 'start-script' stdout output: [info] VPN provider password defined as **** 2016-11-21 12:24:10,987 DEBG 'start-script' stdout output: [info] Default route for container is 2016-11-21 12:24:10,996 DEBG 'start-script' stdout output: [info] Setting permissions recursively on /config/openvpn... 2016-11-21 12:24:10,998 DEBG 'start-script' stdout output: [info] Adding as route via docker eth0 2016-11-21 12:24:10,999 DEBG 'start-script' stdout output: [info] ip route defined as follows... -------------------- 2016-11-21 12:24:11,000 DEBG 'start-script' stdout output: default via dev eth0 2016-11-21 12:24:11,000 DEBG 'start-script' stdout output: dev eth0 proto kernel scope link src via dev eth0 2016-11-21 12:24:11,000 DEBG 'start-script' stdout output: -------------------- 2016-11-21 12:24:11,005 DEBG 'start-script' stdout output: [info] iptable_mangle support detected, adding fwmark for tables 2016-11-21 12:24:11,034 DEBG 'start-script' stdout output: [info] iptables defined as follows... -------------------- 2016-11-21 12:24:11,036 DEBG 'start-script' stdout output: -P INPUT DROP -P FORWARD ACCEPT -P OUTPUT DROP -A INPUT -i tun0 -j ACCEPT -A INPUT -s -d -j ACCEPT -A INPUT -i eth0 -p udp -m udp --sport 1198 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 9091 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --sport 9091 -j ACCEPT -A INPUT -p udp -m udp --sport 53 -j ACCEPT -A INPUT -p icmp -m icmp --icmp-type 0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A OUTPUT -o tun0 -j ACCEPT -A OUTPUT -s -d -j ACCEPT -A OUTPUT -o eth0 -p udp -m udp --dport 1198 -j ACCEPT -A OUTPUT -o eth0 -p tcp -m tcp --dport 9091 -j ACCEPT -A OUTPUT -o eth0 -p tcp -m tcp --sport 9091 -j ACCEPT -A OUTPUT -p udp -m udp --dport 53 -j ACCEPT -A OUTPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT -A OUTPUT -o lo -j ACCEPT 2016-11-21 12:24:11,036 DEBG 'start-script' stdout output: -------------------- [info] nameservers 2016-11-21 12:24:11,037 DEBG 'start-script' stdout output: nameserver nameserver 2016-11-21 12:24:11,037 DEBG 'start-script' stdout output: -------------------- [info] Starting OpenVPN... 2016-11-21 12:24:11,044 DEBG 'start-script' stdout output: Mon Nov 21 12:24:11 2016 OpenVPN 2.3.9 x86_64-unknown-linux-gnu [sSL (OpenSSL)] [LZO] [EPOLL] [MH] [iPv6] built on Dec 24 2015 Mon Nov 21 12:24:11 2016 library versions: OpenSSL 1.0.2f 28 Jan 2016, LZO 2.09 Mon Nov 21 12:24:11 2016 WARNING: file 'credentials.conf' is group or others accessible 2016-11-21 12:24:11,045 DEBG 'start-script' stdout output: Mon Nov 21 12:24:11 2016 UDPv4 link local: [undef] Mon Nov 21 12:24:11 2016 UDPv4 link remote: [AF_INET] 2016-11-21 12:24:11,058 DEBG 'start-script' stdout output: Mon Nov 21 12:24:11 2016 WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this 2016-11-21 12:24:11,123 DEBG 'start-script' stdout output: Mon Nov 21 12:24:11 2016 [2136bcaeca1eddd771c929559cfff859] Peer Connection Initiated with [AF_INET] 2016-11-21 12:24:13,517 DEBG 'start-script' stdout output: Mon Nov 21 12:24:13 2016 TUN/TAP device tun0 opened Mon Nov 21 12:24:13 2016 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Mon Nov 21 12:24:13 2016 /usr/bin/ip link set dev tun0 up mtu 1500 2016-11-21 12:24:13,518 DEBG 'start-script' stdout output: Mon Nov 21 12:24:13 2016 /usr/bin/ip addr add dev tun0 local peer 2016-11-21 12:24:13,522 DEBG 'start-script' stdout output: Mon Nov 21 12:24:13 2016 Initialization Sequence Completed 2016-11-21 12:24:13,554 DEBG 'privoxy-script' stdout output: [info] Privoxy set to disabled 2016-11-21 12:24:13,554 DEBG fd 19 closed, stopped monitoring <POutputDispatcher at 47251779778752 for <Subprocess at 47251779714224 with name privoxy-script in state RUNNING> (stderr)> 2016-11-21 12:24:13,554 DEBG fd 15 closed, stopped monitoring <POutputDispatcher at 47251779711776 for <Subprocess at 47251779714224 with name privoxy-script in state RUNNING> (stdout)> 2016-11-21 12:24:13,554 INFO exited: privoxy-script (exit status 0; expected) 2016-11-21 12:24:13,554 DEBG received SIGCLD indicating a child quit 2016-11-21 12:24:13,558 DEBG 'deluge-script' stdout output: [info] First run detected, setting Transmission listening interface 2016-11-21 12:24:14,039 DEBG 'deluge-script' stdout output: [info] First run detected, setting transmission incoming port 2016-11-21 12:24:14,039 DEBG 'deluge-script' stdout output: [warn] PIA incoming port is not an integer, downloads will be slow, does PIA remote gateway supports port forwarding? [info] All checks complete, starting transmission... 2016-11-21 12:24:15,294 DEBG 'deluge-script' stderr output: [2016-11-21 12:24:15.293] Transmission 2.92 (14714) started (session.c:738) [2016-11-21 12:24:15.294] RPC Server Adding address to whitelist: 192.168.1.* (rpc-server.c:903) [2016-11-21 12:24:15.294] RPC Server Serving RPC and Web requests on port (rpc-server.c:1110) [2016-11-21 12:24:15.294] RPC Server Whitelist enabled (rpc-server.c:1114) [2016-11-21 12:24:15.294] Using settings from "/config" (daemon.c:528) [2016-11-21 12:24:15.294] Saved "/config/settings.json" (variant.c:1266) [2016-11-21 12:24:15.294] Loaded 4 torrents (session.c:2032) [2016-11-21 12:24:15.294] Port Forwarding (NAT-PMP) initnatpmp succeeded (0) (natpmp.c:70) [2016-11-21 12:24:15.294] Port Forwarding (NAT-PMP) sendpublicaddressrequest succeeded (2) (natpmp.c:70) log.txt