grither

sorry for the delay in responding, this worked well, thanks

thanks, should i set it similar to the router router: 192.168.0.1 server: 192.168.0.77 ?? currently server is set to 192.168.2.77

hi all, can't reach my servers but i'm pretty sure its something i did had a shaw router in passthrough mode to a linksys router with address 192.168.2.1. had two unraid servers on same network with ip's 192.168.2.66 and 192.168.2.55 today, the linksys got fried, and i upgraded to a new shaw modem. now i have a shaw model with address 192.168.0.1, but servers still have old addresses above. i cannot reach them! pinging them through windows just results in request timed out. can anyone offer advice?

i had this problem as well... i was in another thread that suggested adding a cron job which restarts all dockers once a day. i've been running about 3 months with no more unusable periods.

thanks all, i should have been a bit more clear. i was wondering if unraid would effectively zero it before adding to the array, thereby taking the array out of commission for several hours...i'd prefer to have it not in the array so that array is usable while the preclear is happening. You have answered that since i know the drive to be good, i did skip the pre read, and may also skip the post read. thanks for the feedback

hi all, i recently upgraded by former 6tg parity drive to an 8tb drive. the former parity drive is still in the server does it need to be precleared before adding as a data drive?

hi all, this is a result of preclear from a new 8tb seagate archive drive... everything look ok? wasn't sure about high fly writes, or Hardware ECC recovered? Disk: /dev/sdh smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.1.17-unRAID] (local build) Copyright © 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST8000AS0002-1NA17Z Serial Number: Z840DGAZ LU WWN Device Id: 5 000c50 087ebda8a Firmware Version: AR15 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5980 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Mar 1 11:18:36 2016 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 947) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 110 100 006 Pre-fail Always - 26155608 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 1 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 073 060 030 Pre-fail Always - 21054474 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 75 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 1 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 088 088 000 Old_age Always - 12 190 Airflow_Temperature_Cel 0x0022 065 062 045 Old_age Always - 35 (Min/Max 21/38) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 2 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 3 194 Temperature_Celsius 0x0022 035 040 000 Old_age Always - 35 (0 21 0 0 0) 195 Hardware_ECC_Recovered 0x001a 110 100 000 Old_age Always - 26155608 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 219988224901195 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 15628053216 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 47793036504 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

so rebuilt parity just fine, excluding disk. Added disk back to array since it appeared like it was 100% fine everything has been fine for the past week, but just now i got an email indicating this disk now has pending sector count of 3. not sure what to do... i could just junk it, but this drama seems to demonstrate that pending sectors on this disk seem to drift up between zero and 5, but not more.... perhaps i leave it in and keep an eye on it? its also a few years old so i'm not too worried about junking it... i guess the best answer is that i'm not really going to trust it, so perhaps it should be out of the array

yes thanks for this! now i just have to shutdown, and peek at which slots the drives are in.. .but will prevent a lot of future trial and error when replacing drives

sorry for the sensational title, however i can't explain this? earlier in the week, got a few warning emails, that i had a pending sector count of 1, then 3, then 5. here's the email i got: Event: unRAID device sdc SMART health [197] Subject: Warning [CHIMERA] - current pending sector is 5 Description: WDC_WD20EARS-00MVWB0_WD-WMAZA0823880 (sdc) Importance: warning later in the week got this: Event: unRAID device sdc SMART message [197] Subject: Notice [CHIMERA] - current pending sector returned to normal value Description: WDC_WD20EARS-00MVWB0_WD-WMAZA0823880 (sdc) Importance: normal i assumed the pending were reallocated so i copied everything off the disk, then ran a pre clear which came up totally normal! and the preclear doesn't show any sectors reallocated? Am i missing something? was unraid mistaken, or are the smart reports coming from the disk screwed up (ie report pending, and then not) preclear finish report attached i'm quite tempted to put the drive back in the array as it looks normal.... preclear_finish_WD-WMAZA0823880_2016-02-13.zip

rebooted once and had same problem. then shut down, opened server and checked a few connections. nothing appeared loose but i pushed everything in. also physically disconnected power for a few seconds. rebooted, fortunately all drives appeared!

tried this a few diff ways, with a couple different slot. now have a new scary problem! gave up and removed the ssd. now when i booted, it appears a bunch of drives are missing! help! very weird my server has 3 controller cards, could one have become dislodged?

hi all, i am trying to add a cache drive to my server. i purchased a 120gb sandisk ssd. powered down, installed, booted up. but system hangs each time. if i remove drive, system boots normal any thoughts? here's a pic of the server screen when it hangs

https://lime-technology.com/wiki/index.php/Replace_A_Cache_Drive saw the above, but wasn't sure if this would stay the same under unraid 6, including having running dockers on the cache drive

hi all, i want to buy a larger cache drive... on my current cache, i have my docker.img, as well as 3 dockers running. also have mover enabled. everything running good, almost hate to play with it! any advice on how to replace? could i copy the cache contents to my pc, then reboot server with new cache installed? or do i need to setup all the docker apps from scratch?

No worries, thanks for all your help!

Yes but now that I'm rebuilding parity without that disk won't it be okay?

uh oh, i had begun a copy of the whole drive to other drives in the array, and then left for work. when i got home it was 99% complete, then finished. I set it to copy before i saw all the recommendations, oops! fortunately i think everything came off okay. i have now removed the drive from the array, and am rebuilidng parity. once parity complete i will run a preclear on the drive, and just see what comes of it. the drive jumped from pending sector, to 3, then to 5, all within about an hour. it appears to have stabilized... but we'll see the results of the preclear. drive is quite old, and out of warranty by 3 years.

http://lime-technology.com/forum/index.php?topic=45286.0 the above fixed an unresponsive server for me. i was locking up every couple of days, now i've been up for over 3 weeks with no prob

yes will do since i don't have a precleared disk ready to go, i am currently copying files off the disk, onto other disks within the array. I suppose that's okay? even if the disk totally fails, i could still rebuild once i have a precleared disk ready?

ok oops, download did nothing, i think because the smart report failed. I am in the process of moving the data off this drive and onto other drives. unfortunately got cuaght without a spare, because i recently lauched a second server and wanted to start using my previous spare, for warranty reasons overnight, got two more messages, that pending had grown to 3, then to 5, then offline uncorrectable at 2. smart report attached if interested chimera-smart-20160209-0432.zip

hi can someone tell me where the smart reports are kept? i ran the extended, but don't know where to see the outcome. there is a button called download, which i clicked but don't know where this saves to!

just my first unraid 6 email warning, saying the above in the subject line. I can post a smart report later tonight, but assuming the pending sector count is only '1', would the community recommend any steps be taken? or just continue to monitor?

exact same situation and UPS on dashboard i get battery charge 100% runtime left 74 minutes (seems too high) nominal power - UPS load - UPS Load % 9.0 percent

thanks very much for the suggestions... good to know there's other things to try, if my current 'fix' stops working. i do not have a large cache drive, therefore i don't think i could afford to have it run only once per week....and plex is my only source for tv also, so i guess having sab run only once per day means you are at least another day delayed in watching shows, which is not the end of the world! Exactly! We found at my house that we normally didn't watch shows until the next day anyhow so my wife never even noticed I changed the download times to have it queue up the stuff during the day and evening hours, but not pull it until the middle of the night. We watch most things next day or over the weekend. She just knows that the server doesn't lockup anymore to where she has to yell at me to reboot it.... Again... Happy wife, happy life.... great server (and wife) management skills!