Alpha2011 Posted September 7, 2022 Share Posted September 7, 2022 (edited) I accidentally nudge a power cable from the box while cleaning causing a shutdown. When i turned it back on it had disconnected disk 2 and had errors in disk 1 after a little tinkering was able to fix disk 1's using xfs repair and rebuild disk 2 back on it self. Parity was completed and it seemed fine but i was greeted with 20k's worth of errors on both disk. I am new to unraid an have little experience with how everything works. Attached are diagnostic files. tower-diagnostics-20220906-2048.zip Edited September 7, 2022 by Alpha2011 Quote Link to comment
Solution JorgeB Posted September 7, 2022 Solution Share Posted September 7, 2022 Could be a power/connection problem, but I would suspect more a controller issue, Marvell controllers are not recommend for Unraid, if possible replace it with one of these. Quote Link to comment
Alpha2011 Posted September 7, 2022 Author Share Posted September 7, 2022 (edited) Ok understood marvel controler is not a good choice. Huat ordered an LSI 9207 I8. Until then how can I have the server up and running, or do I have to wait for the hba and then kick it up again? In any case what are the steps to fix thoses errors? Edited September 7, 2022 by Alpha2011 Quote Link to comment
JorgeB Posted September 7, 2022 Share Posted September 7, 2022 You should be able to keep using the server, reboot to clear the errors and avoid high i/o like parity checks/rebuilds. Quote Link to comment
Alpha2011 Posted September 7, 2022 Author Share Posted September 7, 2022 1 minute ago, JorgeB said: You should be able to keep using the server, reboot to clear the errors and avoid high i/o like parity checks/rebuilds. Ok , perfect I'll keep posting after I receive the LSI card. Thank you very much. Quote Link to comment
Alpha2011 Posted September 13, 2022 Author Share Posted September 13, 2022 Update: Recieved the LSI card. Installed it and cable managed (extremely hard) . Running parity check with out any error or issues so far. 1 Quote Link to comment
Alpha2011 Posted September 17, 2022 Author Share Posted September 17, 2022 (edited) Back to having issues . After a proper rebuild everything was fine until today . I have tried to restore the drive twice to no avail. Is it the dockers I am running that are causing errors? tower-diagnostics-20220917-1815.zip Edited September 17, 2022 by Alpha2011 Quote Link to comment
trurl Posted September 17, 2022 Share Posted September 17, 2022 Disable spindown on disk2 and run extended self-test Quote Link to comment
Alpha2011 Posted September 17, 2022 Author Share Posted September 17, 2022 (edited) Running it now. Here is the output. tower-smart-20220917-1937.zip Edited September 17, 2022 by Alpha2011 Attached files Quote Link to comment
trurl Posted September 17, 2022 Share Posted September 17, 2022 24 minutes ago, Alpha2011 said: Here is the output Diagnostics already includes SMART report for all attached disks. 50 minutes ago, trurl said: Disable spindown on disk2 and run extended self-test Do you know how to run extended self-test? It will take many hours for 6TB drive Quote Link to comment
Alpha2011 Posted September 17, 2022 Author Share Posted September 17, 2022 So I guess I don't how to run it. Quote Link to comment
trurl Posted September 18, 2022 Share Posted September 18, 2022 Click on the disk to get to its Settings page, set Spin down delay to Never. In the Self-Test section (probably where you got that SMART report from), click the Start button next to SMART extended self-test. You can check back there later, it will give you updates in 10% increments. Could take 12 or more hours to complete 6TB unless it decides the disk is bad before it completes. Quote Link to comment
Alpha2011 Posted September 18, 2022 Author Share Posted September 18, 2022 (edited) On 9/17/2022 at 8:09 PM, trurl said: Click on the disk to get to its Settings page, set Spin down delay to Never. In the Self-Test section (probably where you got that SMART report from), click the Start button next to SMART extended self-test. You can check back there later, it will give you updates in 10% increments. Could take 12 or more hours to complete 6TB unless it decides the disk is bad before it completes. Ok understood. Running the test. It's been in 10% for a while. Update : Experiencing a total black out where i live. Will wait for power to be restored and complete all test. Thank you for time Edited September 20, 2022 by Alpha2011 Area condition update. Quote Link to comment
ChatNoir Posted September 18, 2022 Share Posted September 18, 2022 4 hours ago, Alpha2011 said: It's been in 10% for a while. Only increases by 10% increments. Quote Link to comment
JorgeB Posted September 18, 2022 Share Posted September 18, 2022 LSISAS2308: FWVersion(20.00.06.00) This should be updated to 20.00.07.00, all other 20.00.xx releases have known issues. Quote Link to comment
Alpha2011 Posted September 30, 2022 Author Share Posted September 30, 2022 On 9/17/2022 at 6:53 PM, trurl said: Disable spindown on disk2 and run extended self-test Finally completed the Extended Smart test. tower-smart-20220930-1504.zip Quote Link to comment
Alpha2011 Posted September 30, 2022 Author Share Posted September 30, 2022 On 9/18/2022 at 5:32 AM, JorgeB said: LSISAS2308: FWVersion(20.00.06.00) This should be updated to 20.00.07.00, all other 20.00.xx releases have known issues. Completed the firmware update. And complete parity sync Here complete diagnostics. tower-diagnostics-20220930-1506.zip Quote Link to comment
JorgeB Posted October 1, 2022 Share Posted October 1, 2022 Everything looks good, log is clean, just cannot see if the disks are mounting since the rebuild was done in maintenance mode, start the array in normal mode, if all disks are mounting you are done, if not post new diags. Quote Link to comment
Alpha2011 Posted October 1, 2022 Author Share Posted October 1, 2022 4 hours ago, JorgeB said: Everything looks good, log is clean, just cannot see if the disks are mounting since the rebuild was done in maintenance mode, start the array in normal mode, if all disks are mounting you are done, if not post new diags. Had a problem with the xfs filesystem. Was able to fix it in unraid. I have a large set of folders in lost+found. But it is running pretty good. Thank all for the help. 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.