niXta- Posted July 12, 2019 Share Posted July 12, 2019 Hi! I’m running latest nvidia-version unraid (trial) on my z370 add to it has been running well for a few days. Today I restarted it but it got stuck at starting samba and isn’t up yet an hour later. see attached photo of the console. Anyone know what could cause this? Quote Link to comment
Squid Posted July 12, 2019 Share Posted July 12, 2019 Restart in safe modeSent from my NSA monitored device Quote Link to comment
niXta- Posted July 13, 2019 Author Share Posted July 13, 2019 Actually, scratch that, it was up after an unknown time, I hadn't enabled autostart on some dockers witch I was queering, so I thought It was still in the booting sequence. I waited about 5 min before leaving it and it seemed like it was stuck. Now when I'm back, I can see that it has been running. Any reboot atm. is very snappy and works fine. Quote Link to comment
Gsusking2 Posted December 15, 2019 Share Posted December 15, 2019 On 7/12/2019 at 7:21 AM, Squid said: Restart in safe mode Sent from my NSA monitored device Hi squid. I have run into the same problem. I can boot in safe mode. What should I look into. I am an extreme noob just tinkering so there are no dockers. VMs etc. No data to worry about. Quote Link to comment
trurl Posted December 15, 2019 Share Posted December 15, 2019 6 minutes ago, Gsusking2 said: I have run into the same problem. I can boot in safe mode. What should I look into. I am an extreme noob just tinkering so there are no dockers. VMs etc. No data to worry about. You didn't actually mention whether or not you still had the problem after booting in SAFE mode. Go to Tools - Diagnostics and attach the complete diagnostics zip file to your NEXT post. Quote Link to comment
Gsusking2 Posted December 15, 2019 Share Posted December 15, 2019 Hello, I am booted in GUI safe mode, and have attached the Diagnostics. I apologize about not being more clear. 3 minutes ago, trurl said: You didn't actually mention whether or not you still had the problem after booting in SAFE mode. Go to Tools - Diagnostics and attach the complete diagnostics zip file to your NEXT post. tower-diagnostics-20191215-1042.zip Quote Link to comment
trurl Posted December 15, 2019 Share Posted December 15, 2019 38 minutes ago, Gsusking2 said: I apologize about not being more clear. Your are still unclear since you still haven't 42 minutes ago, trurl said: actually mention whether or not you still had the problem after booting in SAFE mode. Quote Link to comment
trurl Posted December 15, 2019 Share Posted December 15, 2019 Have you actually tried to start the array? Quote Link to comment
Gsusking2 Posted December 15, 2019 Share Posted December 15, 2019 15 minutes ago, trurl said: Have you actually tried to start the array? Ok let me start from the top. When trying to launch Unraid in GUI mode it hangs in the same place that the OP is discussing. When i launch in GUI safe mode there is no hang and i am brought to the GUI, i am able to start the Array without a problem. As mentioned before, i dont have any dockers, or VMs, i was trying to set up an UBUNTU vm and it caused a crash. I then Rebooted, and it began to hang on SAMBA startup when launching in GUI mode. Quote Link to comment
trurl Posted December 15, 2019 Share Posted December 15, 2019 1 hour ago, Gsusking2 said: Ok let me start from the top. When trying to launch Unraid in GUI mode it hangs in the same place that the OP is discussing. When i launch in GUI safe mode there is no hang and i am brought to the GUI, i am able to start the Array without a problem. As mentioned before, i dont have any dockers, or VMs, i was trying to set up an UBUNTU vm and it caused a crash. I then Rebooted, and it began to hang on SAMBA startup when launching in GUI mode. Are those diagnostics from after all that? Quote Link to comment
Gsusking2 Posted December 15, 2019 Share Posted December 15, 2019 22 minutes ago, trurl said: Are those diagnostics from after all that? here are the Diagnostics with the array running, in safe mode GUI tower-diagnostics-20191215-1342.zip Quote Link to comment
Klashe Posted August 15, 2020 Share Posted August 15, 2020 (edited) Not trying to gravedig, but I had the same issue. I have a similar setup with AMD CPU and Nvidia GPU bound to a Docker Plex. I believe what happened to me was that I had the GPU connected to a monitor to observe POST, and when UNRAID at some point when the SAMBA portion came up, the Plex Docker was spun up as well and grabbed control of the GPU, suppressing any further output to my monitor. I believe the behavior would be the same if a VM had control of the GPU instead of the docker. So when it looked like UNRAID had froze, it actually completed startup and was successfully up and running, only not output anything to the monitor because UNRAID didn't have the GPU anymore. If you have a similar configuration, before you assume that UNRAID had failed, double check your web interface and see if it's up and running. Edited August 15, 2020 by Klashe Quote Link to comment
GumGum Posted August 12, 2021 Share Posted August 12, 2021 I had the same issue today and had to delete the nvidia-driver folder from the plugins folder on the flash drive. That fixed the issue. More details here Quote Link to comment
cdrsteve Posted May 8, 2023 Share Posted May 8, 2023 (edited) After dealing with this issue for I can't remember how long, I finally got it sorted out. Problem was indeed due to a bad plugin. I booted in Safe Mode, added ".bak" to all installed plugins to rename them, and then rebooted. System rebooted without a problem and I readded my "neccessary" plugins one at a time. My problem was caused by an old version of "Nut" that I failed to uninstall. Installed the now recommended version and all is well! I LOVE Unraid! Edited May 8, 2023 by cdrsteve Typo Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.