radiolex

I seem to have the same issue. Lots of logs related to smbd_audit. It's causing my VMs to stop working since the Logs folder is full. This only started happening after 6.11.1

Hi Everyone, I recently got an Intel i350V2 Quad Network card for my Unraid server. I have disabled my integrated network card. I would like to set it up this way: Port 1/2 (eth0 and eth1) Link Aggregation for all Unraid Services including some dockers Port 3 (eth2) Pi Hole Docker Only Port 4 (eth3) VM The rationale for this setup stems from the fact that I've noticed with Pi-Hole running when using my integrated network card prior to getting the quad network card, all devices on my network were constantly communicating with my server. I found this to bottleneck my network especially when trying to transfer files to and from Unraid. The challenge I'm finding with Port 3 (eth2) is that I can't get it to show up in Docker to allow Pi-Hole to use it. Since I also have Plex and other docker services running, it is already using the bridge from the main configuration. In my docker settings I have: For whatever reason, the option of br2 doesn't show up for me to select in the docker container settings. I'm assuming I have something setup wrong that is preventing it from working. Does anyone have any ideas? Can I only use 1 br interface? Thanks Michael

Have the exact same issue with the same chip. Any ideas?

Has anyone figured out the issue with: Filtering and streamcopy cannot be used together?

Anyone have any success with this?

Hello, Perhaps I'm doing something wrong, but I can't seem to get it to connect. I notice that in the Docker tabs, the intel-gpu-telegraf doesn't have any IP address. This is setup as a host network. Is this normal?

Any luck with this?

Hi Everyone, Unmanic has been great so far however, today it decided to stop working. On all worker logs it's getting the same error and it freezes up the workers. Metadata: encoder : Lavf58.45.100 Stream #0:0(eng): Video: hevc (hevc_qsv), qsv, 1920x1080 [SAR 1:1 DAR 16:9], q=2-31, 1000 kb/s, 23.98 fps, 1k tbn, 23.98 tbc (default) Metadata: encoder : Lavc58.91.100 hevc_qsv Side data: cpb: bitrate max/min/avg: 0/0/1000000 buffer size: 0 vbv_delay: N/A Stream #0:1(eng): Audio: dts (DTS) ([1] [0][0] / 0x2001), 48000 Hz, 5.1(side), fltp, 1536 kb/s (default) [hevc_qsv @ 0x55902d61dc40] Unknown FrameType, set pict_type to AV_PICTURE_TYPE_NONE. Any ideas?

Hi, Is it possible to somehow enable a Hyper-V Enhanced like Session in unraid for a Windows VM? Scenario: I need to be able to use a Cisco VPN however it recognizes that i am remoting into the VM with unraid and won't connect. If i use Hyper-V and install Windows, i can toggle between "basic session" and "enhanced session" which will allow me to connect to the Cisco VPN. The unfortunate part about this is that i have to run the unraid Windows VM and then Hyper-V Windows which degrades the performance. Is this possible in any way in unraid?

Hi Everyone, I seem to have the exact same issue. Was this figured out? I am using the Video Encoder H265/HEVC - hevc_qsv (Intel) "Filtergraph 'hwupload=extra_hw_frames=64,format=qsv' was defined for video output stream 0:5 but codec copy was selected. Filtering and streamcopy cannot be used together."

Hi, I'm new to Unraid and I am trying to set this up. When I edit the Movies.yml, collections that I have removed, keep on re-adding. How do I stop this? Thanks Michael