ptirmal

I have the same issue. I also noticed after my Fios went down for the first time in 5 years and I have a new IP and none of my services address was correctly updated 😐.

That's what I've been doing but wasn't aware that's why it isn't installed. Good to know.

Is there something else you need to do to have it installed on boot? I have done this and it doesn't get installed on boot. I have to manually install the package.

I haven't used borgmatic before. Did you have borg running on previous versions?

I will be following this. I have been putting off updating to 6.11 because I rely on borg backups.

Thanks so much for this. Didn't have time to look far into it, appreciate the info!

If there is no data on the disk you want to swap you can create a new config. This is how you would shrink your array. You would rebuild parity. In this case you either trust the data and rebuild parity or rebuild the empty disk from parity.

Can someone tell me if this is something I need to be concerned about? I am running an Asrock J3455 board with bios 1.80. I have been using this as an offsite backup server. I recently added fix common problems and saw this. It seems to happen at boot. Google doesn't seem to tell me much. It doesn't seem to affect stability as I only interact with it when I want to add a drive or something. backup-diagnostics-20211116-0648.zip

What is the protocol for restoring individual files/folders. Can you browse the .tar via unraid? If so, can someone help with commands to navigate it. My tar is ~50GB and I need to restore a folder that's probably under 10MB. Winrar doesn't seem to like trying to open it via SMB on my Windows 10 computer. Not sure what the best way to do this is.

I'm still trying to figure out how I want it setup, still in the planning stage. I only have one camera hooked up right now as "laundry room," when I go to events I see two folders: "1" and "Laundry room," both have the same events - is this normal? Sorry if this is a Zoneminder question, I am doing my best to search through the documentation. Edit: Sorry I think it was because I created a zone "1" and it was saving those specific motion detection events in addition to the base ones. Was it actually saving those files twice or were the just symlinked?

Thanks for maintaining this docker dlandon! I plan to get two 720p cameras going initially and then add another 2 higher resolution ones later. I am still doing some testing and I think I much prefer this to running Blue Iris in a VM. I had a question about saving recordings. My plan is to run my cameras off an unassigned device drive (3TB) with mocord, I don't see how I can separate motion detected videos, is this possible? My plan was to have a script run every X hours that will rsync the "motion detected" directory to another location. I don't want to sync the entire folder if I am running it in mocord, and I think I would prefer mocord to modetect. Thoughts?

Yes I do. I currently have them notify me via Pushbullet. I also check in on it pretty regularly.

Yea it sucks but that's what backups are for right? I had unbalance on the default settings so I don't know if notifications are enabled by default. I did notice when it was complete it wasn't let me click validate or anything else. I should have looked into it further but I figured it transferred it all since unraid was showing what looked like the correct percentage increase. Oh well, live and learn, could have been worse. And it looks like I'm restoring from my backup so whatever I deemed important survives.

I'm trying to restore from a backup that's stored on another computer on my network. The problem is it's telling me that "there is not enough space available to restore". I haven't changed any settings to the share, but files were removed from the share which is why I want to restore from it. What can be the issue? Plenty of space available. Edit: Think I figured it out, was trying to restore to root. Changed that and looks to be starting the restore.

Those disks were already formatted... I assumed (incorrectly) that the disks had moved the files because it said it was complete. I'm having a separate issue restoring from my crashplan backup.