miniwalks

Members
  • Posts

    226
  • Joined

  • Last visited

Everything posted by miniwalks

  1. if you go to "edit" on the docker, scroll down to the repository line, normally this would read: (latest) binhex/arch-sickchill to rollback to a known working version (with GUI etc) binhex/arch-sickchill:v2021.04.10-1-01
  2. Norco RPC-2212 SuperMicro X8/9/10 with Xeon and ECC LSI card to suit 2U 600W seasonic PSU Done Sent from my iPhone using Tapatalk
  3. I had the same issue with my various zone minder dockers. Unraid docker engine doesn’t handle memory management terribly well, which is what I put it down to Have seen migrated my 15 cameras off to BlueIris on an UnRaid Windows VM Sent from my iPhone using Tapatalk
  4. As per johnnie I’ve seen Black, Blue, Silver and Red all used in OEM server builds for SAS cables Haven’t seen any documented standards on colours or even naming schema for breakout and reverse breakout cables HTH Sent from my iPhone using Tapatalk
  5. If by chance you’re using Safari it’s a known issues with websockets HTH Sent from my iPhone using Tapatalk
  6. Seems that it’s happened again.... @jonp @limetech
  7. It could be that the PSUs you’re using doesn’t support a minimum load as low as the board is using Sent from my iPhone using Tapatalk
  8. What do you mean your ISP doesn’t allow you to forward ports, only CGNAT would allow that to be the case in the ISPs defence. Go to a new ISP who isn’t a douche canoe and go from there would be my bet. Sent from my iPhone using Tapatalk
  9. Do the lines still appear if you take a screenshot? It’s possible your display cable isn’t up to the task Sent from my iPhone using Tapatalk
  10. Diagnostics Screenshots Error Messages Thanks Sent from my iPhone using Tapatalk
  11. FWIW Windows 10 1709 now denies access to unauthenitcated SMB Not sure if this is your case tho Sent from my iPhone using Tapatalk
  12. That list is a good start, but I would recommend avoiding the Marvell based cards on it, as they aren’t as recommended as they used to be. Personally I would stick to the LSI based cards Sent from my iPhone using Tapatalk
  13. Close, Industry standard for STP is 30 seconds, but yes may be up to 50 on legacy hardware. RSTP is between 1 and 3. STP in general is for protecting against loops or “spanning tree storms” where packets continue to forward forever. Common symptoms are all links flooding at 50% of line rate. Later evolutions of STP includes pvRSTP whereby it can be used to guide packets down certain links on a per vlan basis essentially forming a quality of service scheme. This is especially useful when 802.3ad cannot be employed due to hardware limitations or design limitations. Bonding otherwise known as PortChanneling or EtherChannel is the combination of up to 8 links in a group to provide higher bandwidth, however a single client-server connection cannot use more than 1 link at a time. Commonly known as the multi-lane freeway. 802.3ad was brought in during the 100mbps days when 1gbps was considered expensive and is still used today until 40 and 100g-base becomes cheap enough for mass adoption. Sent from my iPhone using Tapatalk
  14. Yeah, I’m more wondering if it’s his switching that might be only running STP and that’s causing the delay in getting an IP ready Sent from my iPhone using Tapatalk
  15. Yeah, I was just thinking if his boot time was too quick for the 30second timeout of standard STP, that it would be worth checking if RSTP is available as that’s a “near instant” initialisation of the port and ensures the DHCP packets can actually pass through without issues. There are still times when you’d want RSTP disables in favor or STP, predominately WAN links and other links where a link flap could be devastating Sent from my iPhone using Tapatalk
  16. LSI based cards LSI2008 chipset got spinners LSI3008 for SSDs Plenty of OEM versions available too; M1015, M1115, M1215, H200, H310, H330 HTH Sent from my iPhone using Tapatalk
  17. Thanks Tom! Sent from my iPhone using Tapatalk
  18. Awesome, I’ll get my hands on one and report back Sent from my iPhone using Tapatalk
  19. @dlandon just out of interest, is your NIC/Switch setup for RSTP?
  20. Jumbo Frames shouldn’t be implemented unless you 400% know what you’re doing. Sent from my iPhone using Tapatalk
  21. Rc14 now available guys Sent from my iPhone using Tapatalk
  22. miniwalks

    Fan Upgrade

    That’s the one Sent from my iPhone using Tapatalk