arcane

I installed mealie today, but am unable to migrate my paprika recipes. The log states: "422 Unprocessable Entity "POST /api/groups/migrations HTTP/1.1" Also, get a similar "unprocessable entity" error when I try to upload an image of a recipe. Any suggestions appreciated!

Thank you MAM59. Yah, I noticed that line indicating that a device claimed the IP address. I found it strange because the device in question was an ASUS device, and I don't have any other computers with an ASUS motherboard (that's why I presumed it was the server itself). I don't have a managed switch, and when I checked the client list for that IP, I didn't find anything. Then it occurred to me that my router is also ASUS. I confirmed that the MAC address belonged to the router. However, I'm confused as to why the router would try to claim that IP since it has never happened before, and it has its own gateway address. Also, in my setup, unRAID is assigned 192.168.11.110 in both the GUI and on the router's DHCP server. Regarding the very similar MAC addresses for the NICs, both are on the motherboard itself, with one being a 10G and the other 2.5G. At the moment, only the 10G is connected. Any other thoughts welcome!

I need to remember the following details. It seems that the MAC hardware address has changed mysteriously. My usual NIC hardware address is CC:28:AA:45:6B:E0, but it changed to 88:d7:f6:b6:2f:00 for some reason. I couldn't access the UnRAID GUI from other computers, so I thought the server had crashed. When I went to check, it was still up. After examining the system logs, I noticed that the IP had changed from 192.168.11.110 to 192.168.11.113. This situation is unusual for two reasons: 1) As far as I know, I don't have a device with the hardware address 88:d7:f6:b6:2f:00, but a reverse MAC search shows that it belongs to my motherboard manufacturer (ASUS). 2) I'm still not sure why the MAC hardware address was changed, but 88:d7:f6:b6:2f:00 had claimed -110 in the past but couldn't keep its lease for some reason. I would appreciate any insight on this. Thank you! tower-diagnostics-20240829-0821.zip

I recently upgraded my old server from a Supermicro with a Xeon E3 to a Gigabyte Z790 with an i5-13500K. Other than adding more memory and some additional NVME drives for cache, all the other components such as hard drives, flash drives, docker containers, and plugins remain the same. I ran a memtest for over 24 hours on both memory sticks without any errors. My plan is to swap in one memory stick at a time to see if it resolves the issue. The Supermicro server was very stable and rarely crashed. Unfortunately, the new hardware has been experiencing random reboots. The longest it has lasted without crashing is about a day, but sometimes it crashes after just 30 minutes, or a few hours in. Thankfully, no data is being written to the array since everything is stored on the cache drives for now. However, I'm worried about crashes occurring when mover eventually writes to the array. There doesn't seem to be any clear cause of the reboots in the syslog. I've set up a remote syslog server as the previous logs are not being saved when it crashes. But the system appears to be operating normally until the time of the crash, and then picks up again after the system reboots. I would appreciate it if some experts could review the diagnostics and suggest further troubleshooting steps. Thank you! tower-diagnostics-20240720-2122.zip

How does one run unbalanced as user "nobody"? I ran new permissions on a share I was moving, but it appears some of the directories had changed ownership to root. Thank you.

Installed MotionEye and was able to set up the camera and view RTSP stream. However, while it seems to be recording, I cannot play the video in the browser or after downloading it. It states that it is "unsupported media" even after changing various codecs. Any suggestions? Thank you.

Installed MotionEye and was able to set up the camera and view RTSP stream. However, while it seems to be recording, I cannot play the video in the browser or after downloading it. It states that it is "unsupported media" even after changing various codecs. Any suggestions? Thank you.

Still getting the XDG error with the latest pull. Any options to get it working? Thank you.

Unfortunately, I'm still getting the "ERROR: openbox-xdg-autostart requires PyXDG to be installed" and having it time out. I have tried setting it to no user and pass, user with no pass in an MD5 hash, default abc and abc password as hash, empty in both setup variables, no luck. Any suggestions? Thank you.

I just tried to install this Docker and everything downloaded fine but would not install. The error is: Error: failed to register layer: ApplyLayer exit status 1 stdout: stderr: write /usr/share/file/magic.mgc: no space left on device Couldn't find any reference to it so would appreciate some guidance. Both my flash and cache drives are over 98% free.

Thank you Frank. No wonder I missed it as it was in another place entirely!

@dlandon I've just installed this plugin to disable Telnet but noticed that there is not an option for that. Has it been removed?

Just installed the plugin today and didn't notice that there was a toggle for disabling telnet, only FTP. Am I missing something?

Hello, Having an issue with Privoxy, as I just realized that connections are not routed through it. Though, if I connect manually to the VPN to verify credentials, it works. I had it set up with a custom OpenVPN and it seems to connect fine according to the log. I can also download torrents but not sure if it is going through the VPN. How do I verify if deluge is actually using the VPN? And any suggestions to resolve problems with Privoxy?

Hmmm... that's what I thought but not sure how to update it. I don't think there's a crt specified in the ovpn file. I'm running my own VPN on AWS through streisand. If you have any suggestions, I'd appreciate it. Thanks!