mustava

is there anyway i can force the plugin to use the old 460 drivers?

After some further research, it seems to be a Linux/Unix/VMware/Nvidia driver issue. GPU works fine passed through to windows. As per the previous users issues, apparently driver version 460 was the last confirmed working. Apparently the new beta versions worked if the opensource kernel modules are used?

Hi All, I have just installed a 1660Super into my Unraid (6.11.4) server and am following the process outlined in this thread to get it up and running, but am experiencing a few issues. Although my GPU is shown in my system devices, once I have installed the nvidia-driver (driver 525.53) plugin, anytime anything interacts with the GPU the whole server hands and i need to reboot. This is both with the array started and stopped. This includes: - Generating diagnostics (when nvidia-driver is installed) - Launching the plugin settings page The devices is shown in System-devices as: [10de:21c4] 1c:00.0 VGA compatible controller: NVIDIA Corporation TU116 [GeForce GTX 1660 SUPER] (rev a1) A few notes: I am running under vmware, but pass-through works seamlessly on 3-4 other devices including PCI devices, and iGPU. I have attached the diagnostics I can access, but I cannot generate them with the plugin install, as it gets stuck on nvidia-smi.txt Appreciate any advice tower-diagnostics-20221119-2354.zip

Attached tower-diagnostics-20210605-1113.zip

If I assume the disk is fine, is there a way i can add it back to the array without rebuilding?

I did reboot

Hi All, I recently swapped my CPU over to a higher model. Upon reboot of Unraid, one of my disks became disabled. Initial inspections of the disk, it appears healthy? I am unsure of the process to re-enable this drive? do I have to rebuild it? is there anyway to re-enable it without a rebuild? Appreciate any advice! tower-smart-20210604-0117.zip

After some further tests, i found that anything < 1400 works.... although everything else in my network sits at 1500. MTU is set at default of 1500 everywhere including interfaces, and dhcp server

Hi All, I have encountered a very strange issue that im struggling with. For some reason I cant pull any images from docker unless my Eth/bond MTU is set to 900. (down from 1500). My network and DNS all work as expected, also tested from the Unraid cli. Will running 900 MTU cause me any performance issues? I am surprised that it has any effect on pulling images from docker?! Any help or advice would be appreciated.

I am now getting this error too. I have checked my DNS and everything else is resolving fine.

Wow ok - I just found the issue by chance two minutes after writing this, despite trying to fix it for hours.... Due to the new ESX installation, the vSwitch for my LAN network had the 'MAC address changes' security setting set to 'Reject'. Reject. If the guest OS changes the effective MAC address of the virtual machine to a value that is different from the MAC address of the VM network adapter (set in the .vmx configuration file), the switch drops all inbound frames to the adapter. If the guest OS changes the effective MAC address of the virtual machine back to the MAC address of the VM network adapter, the virtual machine receives frames again. I guess due to the OS having existing values, and the new install/new NIC's were assigned different values and frames were being blocked by the switch. The more interesting thing is why it worked, slowly, rather than at all...

Hi All, I successfully upgraded from esx 6.7 u2to esx 7.0 Last night. I had a bit more of a bumpy experience, Thus far: Had an issue updating the existing usb bases esx install... installed as per normal upgrade process, successfully booted from USB into esx 7.0 and started up all my VM's including unraid 100% perfect. Needed to reboot the server to toggle pass-through on a device... ESX never came back up (vmware recovery error) and forced me to start from scratch Re-installed ESX 7.0 and re-registered VM's. Boot unraid perfectly, everything comes back up perfectly including my RDM's for onboard attached sata drives. (I have a mix of RDM's and pass through drives which have been rock solid in 6.7) From this point, I have started noticing super slow performance. First in plex, and now upon further inspection even just browsing my shares. It takes a full minute to even open a share or sub folder. This is true even with nothing else is running on the server. Any one have any ideas? I cant see any suspect errors in the logs. Good luck to anyone taking the plunge!

That sounds exactly the same as my issue. CPU gets stuck at 100% and cant reboot the server. I will try unplugging the drive next time the issue occurs.

Yes still same issue, even if i stop everything using the Disk / Array I still cant shutdown the server cleanly. Is there a way to restart the Unassigned Plugin?

Hi All, I am encountering an issue where each morning, I log into Unraid to find Unassigned devices unresponsive. Everything in the GUI and array is responsive, except the one disk mounted via unassigned devices and the GUI for unassigned devices. (just the loading animation). The disk is being used by a VM to write to over night as a bit of a scratch disk. I Also am unable to shutdown or reboot the server in this state, I am required to do a hard power off in order to restart everything. I am worried doing this is going to cause problems pretty quickly. Has anyone had this issue before?