Aspect

No bios updates for me this is a very old dell system. still cant boot on 6.12.4

I did still same issue for me.

I don’t want to jack the thread as I have created my own but just wanted to mention I’m having the exact same issue and have tried all troubleshooting steps I’ve seen mentioned on the forum.

I upgraded one server no issue. The other however will not boot it crashes right after the auto start and the bzroot line comes up a small red line appears horizontally across the screen then the server reboots and it keeps doing that over and over again. But if I replace the flash drive files with the backup it boots right into 6.11.5.

i do not have the errorcode 14 but my logs are flooded with IPV6 errors. would be nice if there was something in the template to turn off IPV6 as i don't believe the urbackup app itself has this built in yet. i notice people complain about this directly on their forum too.

@trurlI 100% don't have an other devices or anything logged into the server. i do have pfBlocker_NG on my pfsense FW but i have had that with no changes for about 3-4years so i don't see why it would affect it now?

I cant even make this up right after posting the above i logged into the server and its stuck with the staring services... notification in the bottom right while everything seems fine and running. I really have no clue what to do at this point.....

I'm going to mark this as solved as I am currently running with 9 days up time with no issue. not exactly sure what resolved the issue but below is what I changed in the process of trying to figure it out. I'm on AMD so i changed some BIOS settings for C-states "Power Supply Idle Control" set it to "typical current idle". as well as disabled global C-States i moved my USB boot drive from a front panel USB port to an on motherboard USB 2.0 port i installed the plug in to auto remount the USB boot drive if it unmounts for any reason Changed the IPs my FW and servers where using form 105.55.5.0/24 to 10.10.5.0/24 Switched Docker from macvlan to ipvlan Hopefully i don't jinx myself but i think i am back to running normally.

Uptime 6 days 12 hours 12 minutes Might have fixed it!!!!!!!!! Fingers crossed.

understood that will be the next thing i try. will i need to mess with anything with the dockers i have setup or is that just as simple as switch it and see what happens with the crashing?

understood. could macvlan conflicts or my dockers in general be causing these issues?

@trurl no i do not currently just the 1 tab open for unraid webUI. only 2 devices i log into this server are my computer and phone. phone is logged out and this computer has 1 tab open. can it cause an issue when there is a big difference in shares when running these 2 commands? ls -al /mnt/user and ls -al /boot/config/shares

@trurl @JorgeB So this morning i logged in to check to make sure the server wasn't in a soft crash state, its not fully in the state i had started this thread for, now it seems normal other than the fact that its stuck saying starting services in the bottom left even though everything is started and has been for 2 days. i checked in a private browser and on chrome and Firefox and still shows the same. output of df -h / is root@Rocky:~# df -h / Filesystem Size Used Avail Use% Mounted on rootfs 32G 2.1G 30G 7% / so it went up by .1GB. there are no notifications or errors other than the "starting services" notification. i'm attaching the current diagnostics. since i last posted i have moved the USB to a 2.0 space directly on the motherboard and changed the IP range that my servers are on. is there any chance this is a symptom of a dying USB? the one that's in this server has been there for a few years and it use to be in a 3.0 slot until i read that that can cause it to burn out quicker. I'm at a lose and don't know what to do this is becoming an upsetting issue because no matter what i do i cant seem to find or resolve the problem. rocky-diagnostics-20230212-1011.zip

I changed it realized my mistake. using 10.10.5.0/24 now.