dojesus Posted April 6, 2022 Share Posted April 6, 2022 I recently updated my power supply and now no mechanical drives are showing. I have 8 on a backplane connected to an LSI card and 1 connected to onboard SATA. NONE are showing up in unRAID. I figured there was something wrong with the PSU and swapped back...same issue. I'm thoroughly stumped on this. All NVME drives are there. I have 1 SATA SSD connected to the MB SATA port, and it shows up. None of my spinning drives are showing...or spinning as far as I can tell. Any suggestions are welcome, because I've pulled out what little hair I had on this one. Quote Link to comment
Vr2Io Posted April 6, 2022 Share Posted April 6, 2022 10 minutes ago, dojesus said: I have 1 SATA SSD connected to the MB SATA port, and it shows up. Stop array, connect a problem disk to SSD plug/cable, if no spinup or disk detection, then likely disk burn-out. Quote Link to comment
dojesus Posted April 6, 2022 Author Share Posted April 6, 2022 (edited) 8 mechanical drives, 8 on a backplane and 1 not. Impossible that all failed simultaneously. Edited April 6, 2022 by dojesus Quote Link to comment
ChatNoir Posted April 6, 2022 Share Posted April 6, 2022 28 minutes ago, dojesus said: I recently updated my power supply If you used a modular power supply, did you change the leads between the PSU and the peripherals ? Those are not standard and can cause issues. Quote Link to comment
dojesus Posted April 6, 2022 Author Share Posted April 6, 2022 Yes it is modular and I've changed port positions and cables. Even putting old PSU back in didn't change anything. Quote Link to comment
itimpi Posted April 6, 2022 Share Posted April 6, 2022 If the power supply was faulty (or you used the wrong cables with a modular supply) then you could burn out the electronics on all the drives. Hopefully that is not what has happened in your case but your symptoms suggest it is a possibility. Quote Link to comment
dojesus Posted April 6, 2022 Author Share Posted April 6, 2022 Well, I was having random shut downs and heat wasn't an issue. The PSU a little long in the tooth, so I decided to upgrade the Thermaltake with a new 850watt 80 gold Seasonic. I'd hate to believe that I lost 30+ TB of data due to a PSU upgrade. Quote Link to comment
JonathanM Posted April 6, 2022 Share Posted April 6, 2022 4 hours ago, dojesus said: Yes it is modular and I've changed port positions and cables. Even putting old PSU back in didn't change anything. If you left ANY of the leads from the old PSU connected to the drives and connected the new PSU to them, it likely burnt out the circuit boards on the drives. There are companies online that can help with board replacement, it's typically much cheaper than full drive recovery. 1 Quote Link to comment
dojesus Posted April 7, 2022 Author Share Posted April 7, 2022 Thanks for all the input. Yes, it appears my own idiocy caused this problem.i didn't swap the modular cables believing them to be standardized. Quote Link to comment
dojesus Posted April 7, 2022 Author Share Posted April 7, 2022 18 hours ago, JonathanM said: There are companies online that can help with board replacement, it's typically much cheaper than full drive recovery. I believe I've tracked down all the replacement circuit boards for all the drives on ebay. Thanks for the advice. Quote Link to comment
JonathanM Posted April 7, 2022 Share Posted April 7, 2022 6 hours ago, dojesus said: I believe I've tracked down all the replacement circuit boards for all the drives on ebay. Thanks for the advice. Some drive models require transplanting parts from the dead board to the donor board, if you are attempting this recovery yourself be sure to get all the relevant info specific to your particular drives. 1 Quote Link to comment
dojesus Posted April 9, 2022 Author Share Posted April 9, 2022 On 4/7/2022 at 7:29 AM, JonathanM said: Some drive models require transplanting parts from the dead board to the donor board, if you are attempting this recovery yourself be sure to get all the relevant info specific to your particular drives. Only 1 drive requires a rom swap. Thanks for the heads up. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.