MrYoshii Posted January 10, 2020 Share Posted January 10, 2020 Hi if tried to update my system from next to stable but its not working. i have addet the error message and the diagnostics log. thx for your help. homeserver01-diagnostics-20200110-1301.zip Quote Link to comment
JorgeB Posted January 10, 2020 Share Posted January 10, 2020 Flash drive problems, run chkdsk on it. Quote Link to comment
MrYoshii Posted January 10, 2020 Author Share Posted January 10, 2020 i have tryed stopping the array but now its stuck and its showing retry unmounting disk share(s)... Quote Link to comment
MrYoshii Posted January 10, 2020 Author Share Posted January 10, 2020 also i can not umount /dev/sda1 its busy. Quote Link to comment
JorgeB Posted January 10, 2020 Share Posted January 10, 2020 You might need to force it. Quote Link to comment
MrYoshii Posted January 10, 2020 Author Share Posted January 10, 2020 force what? Quote Link to comment
MrYoshii Posted January 14, 2020 Author Share Posted January 14, 2020 ok so now i got a new flash drive. i have installed unraid on it with the tool. now can i just copy my old config folder on the new drive? Quote Link to comment
JorgeB Posted January 14, 2020 Share Posted January 14, 2020 Yes, you'll also need to transfer the key. Quote Link to comment
MrYoshii Posted January 14, 2020 Author Share Posted January 14, 2020 ok thx its running again. can be closed Quote Link to comment
trurl Posted January 14, 2020 Share Posted January 14, 2020 51 minutes ago, MrYoshii said: i got a new flash drive Was there something actually wrong with the old flash? Are you booting from a USB2 port? You should be. Quote Link to comment
MrYoshii Posted January 14, 2020 Author Share Posted January 14, 2020 yes the flash drive failed. After i hit reboot it never came up again. I plugged it in my pc and start copying the unraid installation. In the middle of the copying it failed again but this time the drive was completely dead. Now im booting from usb3 port and it works just fine. Quote Link to comment
trurl Posted January 14, 2020 Share Posted January 14, 2020 16 minutes ago, MrYoshii said: Now im booting from usb3 port and it works just fine. Still recommend booting from USB2 port. USB3 often gives problems with disconnects for the Unraid boot flash, and USB3 speed has no benefit for the Unraid flash since it just loads the OS into RAM at boot and the OS runs in RAM. Quote Link to comment
MrYoshii Posted January 14, 2020 Author Share Posted January 14, 2020 ok thx i will keep that in mind. Quote Link to comment
MrYoshii Posted January 20, 2020 Author Share Posted January 20, 2020 i have another question. Why dit it not notice the error? on the screenshot it says 0 errors but the flash was already gone. Quote Link to comment
JorgeB Posted January 20, 2020 Share Posted January 20, 2020 Errors column for cache and flash device are currently just for show, it works for array devices. Quote Link to comment
MrYoshii Posted January 20, 2020 Author Share Posted January 20, 2020 ok but i think it would be nice if it can send a email or so when the flash drive has read/write errors. Quote Link to comment
JorgeB Posted January 20, 2020 Share Posted January 20, 2020 You can install the FCP plugin, it warns if flash goes read-only. Quote Link to comment
Zonediver Posted January 20, 2020 Share Posted January 20, 2020 (edited) FCP = Fix Common Problems 😉 (FYI) Edited January 20, 2020 by Zonediver Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.