Jump to content

JorgeB

Moderators
 View Profile  See their activity

  • Posts

    63,741

  • Joined

  • Last visited

  • Days Won

    674

 Content Type 

Everything posted by JorgeB

  1. JorgeB
    This is from one of my servers, only FAN2 has data, both using the config editor or editing /config/plugins/ipmi/ipmi-sensors.config, using an X11SSM-F:
  2. JorgeB
    Please lets us know if it helps.
  3. JorgeB
    You definitely don't want to use the 4 Marvell ports on those boards, you're going to have disks dropping willy-nilly.
  4. JorgeB
    It doesn't on mine, there's only the warning on the log (orange triangle), only when it drops below the critical threshold the fans ramp up (red x on the log)
  5. JorgeB
    Not really, it's going lower than non-critical, that shouldn't cause fans to ramp up, are you using latest bios and BMC firmware?
  6. JorgeB
    Why not backup the libvirt.img? All you need to restore VMs is that and the vdisks.
  7. JorgeB
    Settings -> VM Manger -> (Advanced mode enable) - Libvirt storage location:
  8. JorgeB
    Do you backup the libvirt.img? If yes just restore that.
  9. JorgeB
    With the 3pin cable they should always work at max speed, or you can select the "Full Speed" profile.
  10. JorgeB
    Not sure, but your fans are going to low in any case, they are dropping below 500rpm, and unless they are very big fans they won't cool much at these speeds, you should get fans that don't go below 800/900rpm with low pwm settings. If you're using the Optimal profile you can try switching to Standard and see if there's any difference.
  11. JorgeB
    Clear the event log and post it again after a couple of minutes.
  12. JorgeB
    As it's visible in the logs fans 1, 2 and 3 are going lower than critical, which is set at 540rpm, you need to lower that, set lower critical at 300 and lower non-recover at 0 or 150.
  13. JorgeB
    Something still wrong with the thresholds, on the IPMI settings, clear the event Log, browse to main page and then go there again after a couples of minutes and post the log.
  14. JorgeB
    I tested on an X9SCM and it only accepts a different threshold value if it's a multiple of 150, so you can only change the thresholds to 150, 300, 450, etc.
  15. JorgeB
    Maybe it doesn't work on the X9 series, or it only accepts some specific values, I can test on one of my servers with the same board but most likely not before tomorrow.
  16. JorgeB
    Try lowering only the lower non recoverable to 200
  17. JorgeB
    The same happened on one of my servers, there was only data for one of the fans, you can do it on the console: 1) download current config to a text file ipmi-sensors-config --checkout --filename=sensordata.conf 2) use an editor like nano to change the values you want nano -w sensordata.conf ctrl+o to save, ctrl+x to exit nano 3) commit the changes ipmi-sensors-config --commit --filename=sensordata.conf
  18. JorgeB
    This only works on X10/X11, it won't work on the X9 series.
  19. JorgeB
    Saarg already told you where to set them: settings -> ipmi - readings -> sensors config
  20. JorgeB
    Any cache files are not parity protected if that's what you mean, and unRAID can't fix corrupt files, it can fix a failed array device.
  21. JorgeB
    Plugin only runs on array devices, also btrfs already cheksums all data, so it's not needed.
  22. JorgeB
    dotm looks like it's day of the month, mode not sure, my is set at 3, but was able to change what I wanted, thanks.
  23. JorgeB
    Not really the right thread but didn't want to make a new one about this, my VM unRAID server is currently running without parity, and to my surprise although I can't set a parity check schedule (which I expected) it still started a read check based on the old schedule I had set when there was parity, I don't mind it running since it's a good way to test all disks but would like to change the current schedule, any way I can do it in the CLI without re-adding parity?
  24. JorgeB
    Looks like it, the raw commands to get/set the auto mode work on my X9, the commands for the speed steps don't work.
  25. JorgeB
    If anyone else wants to try: ipmitool raw 0x30 0x70 0x66 0x01 0x00 0x64 00 - Get value 01 - Set value 00 - FAN 1/2/3/4 01 - FAN A (possibly different groupings on some models) 00 to 64 - Speed (64 is max)
×
×
  • Create New...