skois

Aha, I see, I'll give it a shot then. The next shot will be at shinobi to reduce delay (right now is about 30s) but its only using 3% cpu! Sent from my Mi 10 Pro using Tapatalk

Hello, i'm trying to setup the MotionEye docker. I have 3 IP Cameras set to 1080p - 15fps - mkv/V4L2M2M Format When all 3 is capturing my CPU uses 20-25% (It's a Threadripper 2920!) and i think its a bit high for this kind of cpu. Tried also passthrough but still had about the same. (18-23%) I run on the docker's console the ffmpeg -hwaccels, and i got this: /tmp # ffmpeg -hwaccels ffmpeg version 4.2.1 Copyright (c) 2000-2019 the FFmpeg developers built with gcc 9.2.0 (Alpine 9.2.0) configuration: --prefix=/usr --enable-avresample --enable-avfilter --enable-gnutls --enable-gpl --enable-libass --enable-libmp3lame --enable-libvorbis --enable-libvpx --enable-libxvid --enable-libx264 --enable-libx265 --enable-libtheora --enable-libv4l2 --enable-postproc --enable-pic --enable-pthreads --enable-shared --enable-libxcb --disable-stripping --disable-static --disable-librtmp --enable-vaapi --enable-vdpau --enable-libopus --disable-debug libavutil 56. 31.100 / 56. 31.100 libavcodec 58. 54.100 / 58. 54.100 libavformat 58. 29.100 / 58. 29.100 libavdevice 58. 8.100 / 58. 8.100 libavfilter 7. 57.100 / 7. 57.100 libavresample 4. 0. 0 / 4. 0. 0 libswscale 5. 5.100 / 5. 5.100 libswresample 3. 5.100 / 3. 5.100 libpostproc 55. 5.100 / 55. 5.100 Hardware acceleration methods: vdpau vaapi Is the HW accel enabled? If not how i can enable it? Also ffmpeg -encoders output: / # ffmpeg -encoders ffmpeg version 4.2.1 Copyright (c) 2000-2019 the FFmpeg developers built with gcc 9.2.0 (Alpine 9.2.0) configuration: --prefix=/usr --enable-avresample --enable-avfilter --enable-gnutls --enable-gpl --enable-libass --enable-libmp3lame --enable-libvorbis --enable-libvpx --enable-libxvid --enable-libx264 --enable-libx265 --enable-libtheora --enable-libv4l2 --enable-postproc --enable-pic --enable-pthreads --enable-shared --enable-libxcb --disable-stripping --disable-static --disable-librtmp --enable-vaapi --enable-vdpau --enable-libopus --disable-debug libavutil 56. 31.100 / 56. 31.100 libavcodec 58. 54.100 / 58. 54.100 libavformat 58. 29.100 / 58. 29.100 libavdevice 58. 8.100 / 58. 8.100 libavfilter 7. 57.100 / 7. 57.100 libavresample 4. 0. 0 / 4. 0. 0 libswscale 5. 5.100 / 5. 5.100 libswresample 3. 5.100 / 3. 5.100 libpostproc 55. 5.100 / 55. 5.100 Encoders: V..... = Video A..... = Audio S..... = Subtitle .F.... = Frame-level multithreading ..S... = Slice-level multithreading ...X.. = Codec is experimental ....B. = Supports draw_horiz_band .....D = Supports direct rendering method 1 ------ V..... a64multi Multicolor charset for Commodore 64 (codec a64_multi) V..... a64multi5 Multicolor charset for Commodore 64, extended with 5th color (colram) (codec a64_multi5) V..... alias_pix Alias/Wavefront PIX image V..... amv AMV Video V..... apng APNG (Animated Portable Network Graphics) image V..... asv1 ASUS V1 V..... asv2 ASUS V2 V..... avrp Avid 1:1 10-bit RGB Packer V..X.. avui Avid Meridien Uncompressed V..... ayuv Uncompressed packed MS 4:4:4:4 V..... bmp BMP (Windows and OS/2 bitmap) V..... cinepak Cinepak V..... cljr Cirrus Logic AccuPak V.S... vc2 SMPTE VC-2 (codec dirac) VFS... dnxhd VC3/DNxHD V..... dpx DPX (Digital Picture Exchange) image VFS... dvvideo DV (Digital Video) V.S... ffv1 FFmpeg video codec #1 VF.... ffvhuff Huffyuv FFmpeg variant V..... fits Flexible Image Transport System V..... flashsv Flash Screen Video V..... flashsv2 Flash Screen Video Version 2 V..... flv FLV / Sorenson Spark / Sorenson H.263 (Flash Video) (codec flv1) V..... gif GIF (Graphics Interchange Format) V..... h261 H.261 V..... h263 H.263 / H.263-1996 V..... h263_v4l2m2m V4L2 mem2mem H.263 encoder wrapper (codec h263) V.S... h263p H.263+ / H.263-1998 / H.263 version 2 V..... libx264 libx264 H.264 / AVC / MPEG-4 AVC / MPEG-4 part 10 (codec h264) V..... libx264rgb libx264 H.264 / AVC / MPEG-4 AVC / MPEG-4 part 10 RGB (codec h264) V..... h264_v4l2m2m V4L2 mem2mem H.264 encoder wrapper (codec h264) V..... h264_vaapi H.264/AVC (VAAPI) (codec h264) V..... libx265 libx265 H.265 / HEVC (codec hevc) V..... hevc_v4l2m2m V4L2 mem2mem HEVC encoder wrapper (codec hevc) V..... hevc_vaapi H.265/HEVC (VAAPI) (codec hevc) VF.... huffyuv Huffyuv / HuffYUV V..... jpeg2000 JPEG 2000 VF.... jpegls JPEG-LS VF.... ljpeg Lossless JPEG VF.... magicyuv MagicYUV video VFS... mjpeg MJPEG (Motion JPEG) V..... mjpeg_vaapi MJPEG (VAAPI) (codec mjpeg) V.S... mpeg1video MPEG-1 video V.S... mpeg2video MPEG-2 video V..... mpeg2_vaapi MPEG-2 (VAAPI) (codec mpeg2video) V.S... mpeg4 MPEG-4 part 2 V..... libxvid libxvidcore MPEG-4 part 2 (codec mpeg4) V..... mpeg4_v4l2m2m V4L2 mem2mem MPEG4 encoder wrapper (codec mpeg4) V..... msmpeg4v2 MPEG-4 part 2 Microsoft variant version 2 V..... msmpeg4 MPEG-4 part 2 Microsoft variant version 3 (codec msmpeg4v3) V..... msvideo1 Microsoft Video-1 V..... pam PAM (Portable AnyMap) image V..... pbm PBM (Portable BitMap) image V..... pcx PC Paintbrush PCX image V..... pgm PGM (Portable GrayMap) image V..... pgmyuv PGMYUV (Portable GrayMap YUV) image VF.... png PNG (Portable Network Graphics) image V..... ppm PPM (Portable PixelMap) image VF.... prores Apple ProRes VF.... prores_aw Apple ProRes (codec prores) VFS... prores_ks Apple ProRes (iCodec Pro) (codec prores) V..... qtrle QuickTime Animation (RLE) video V..... r10k AJA Kona 10-bit RGB Codec V..... r210 Uncompressed RGB 10-bit V..... rawvideo raw video V..... roqvideo id RoQ video (codec roq) V..... rv10 RealVideo 1.0 V..... rv20 RealVideo 2.0 V..... sgi SGI image V..... snow Snow V..... sunrast Sun Rasterfile image V..... svq1 Sorenson Vector Quantizer 1 / Sorenson Video 1 / SVQ1 V..... targa Truevision Targa image V..... libtheora libtheora Theora (codec theora) VF.... tiff TIFF image VF.... utvideo Ut Video V..... v210 Uncompressed 4:2:2 10-bit V..... v308 Uncompressed packed 4:4:4 V..... v408 Uncompressed packed QT 4:4:4:4 V..... v410 Uncompressed 4:4:4 10-bit V..... libvpx libvpx VP8 (codec vp8) V..... vp8_v4l2m2m V4L2 mem2mem VP8 encoder wrapper (codec vp8) V..... vp8_vaapi VP8 (VAAPI) (codec vp8) V..... libvpx-vp9 libvpx VP9 (codec vp9) V..... vp9_vaapi VP9 (VAAPI) (codec vp9) V..... wmv1 Windows Media Video 7 V..... wmv2 Windows Media Video 8 V..... wrapped_avframe AVFrame to AVPacket passthrough V..... xbm XBM (X BitMap) image V..... xface X-face image V..... xwd XWD (X Window Dump) image V..... y41p Uncompressed YUV 4:1:1 12-bit V..... yuv4 Uncompressed packed 4:2:0 VF.... zlib LCL (LossLess Codec Library) ZLIB V..... zmbv Zip Motion Blocks Video A..... aac AAC (Advanced Audio Coding) A..... ac3 ATSC A/52A (AC-3) A..... ac3_fixed ATSC A/52A (AC-3) (codec ac3) A..... adpcm_adx SEGA CRI ADX ADPCM A..... g722 G.722 ADPCM (codec adpcm_g722) A..... g726 G.726 ADPCM (codec adpcm_g726) A..... g726le G.726 little endian ADPCM ("right-justified") (codec adpcm_g726le) A..... adpcm_ima_qt ADPCM IMA QuickTime A..... adpcm_ima_wav ADPCM IMA WAV A..... adpcm_ms ADPCM Microsoft A..... adpcm_swf ADPCM Shockwave Flash A..... adpcm_yamaha ADPCM Yamaha A..... alac ALAC (Apple Lossless Audio Codec) A..... aptx aptX (Audio Processing Technology for Bluetooth) A..... aptx_hd aptX HD (Audio Processing Technology for Bluetooth) A..... comfortnoise RFC 3389 comfort noise generator A..X.. dca DCA (DTS Coherent Acoustics) (codec dts) A..... eac3 ATSC A/52 E-AC-3 A..... flac FLAC (Free Lossless Audio Codec) A..... g723_1 G.723.1 A..X.. mlp MLP (Meridian Lossless Packing) A..... mp2 MP2 (MPEG audio layer 2) A..... mp2fixed MP2 fixed point (MPEG audio layer 2) (codec mp2) A..... libmp3lame libmp3lame MP3 (MPEG audio layer 3) (codec mp3) A..... nellymoser Nellymoser Asao A..X.. opus Opus A..... libopus libopus Opus (codec opus) A..... pcm_alaw PCM A-law / G.711 A-law A..... pcm_dvd PCM signed 16|20|24-bit big-endian for DVD media A..... pcm_f32be PCM 32-bit floating point big-endian A..... pcm_f32le PCM 32-bit floating point little-endian A..... pcm_f64be PCM 64-bit floating point big-endian A..... pcm_f64le PCM 64-bit floating point little-endian A..... pcm_mulaw PCM mu-law / G.711 mu-law A..... pcm_s16be PCM signed 16-bit big-endian A..... pcm_s16be_planar PCM signed 16-bit big-endian planar A..... pcm_s16le PCM signed 16-bit little-endian A..... pcm_s16le_planar PCM signed 16-bit little-endian planar A..... pcm_s24be PCM signed 24-bit big-endian A..... pcm_s24daud PCM D-Cinema audio signed 24-bit A..... pcm_s24le PCM signed 24-bit little-endian A..... pcm_s24le_planar PCM signed 24-bit little-endian planar A..... pcm_s32be PCM signed 32-bit big-endian A..... pcm_s32le PCM signed 32-bit little-endian A..... pcm_s32le_planar PCM signed 32-bit little-endian planar A..... pcm_s64be PCM signed 64-bit big-endian A..... pcm_s64le PCM signed 64-bit little-endian A..... pcm_s8 PCM signed 8-bit A..... pcm_s8_planar PCM signed 8-bit planar A..... pcm_u16be PCM unsigned 16-bit big-endian A..... pcm_u16le PCM unsigned 16-bit little-endian A..... pcm_u24be PCM unsigned 24-bit big-endian A..... pcm_u24le PCM unsigned 24-bit little-endian A..... pcm_u32be PCM unsigned 32-bit big-endian A..... pcm_u32le PCM unsigned 32-bit little-endian A..... pcm_u8 PCM unsigned 8-bit A..... pcm_vidc PCM Archimedes VIDC A..... real_144 RealAudio 1.0 (14.4K) (codec ra_144) A..... roq_dpcm id RoQ DPCM A..X.. s302m SMPTE 302M A..... sbc SBC (low-complexity subband codec) A..X.. sonic Sonic A..X.. sonicls Sonic lossless A..X.. truehd TrueHD A..... tta TTA (True Audio) A..X.. vorbis Vorbis A..... libvorbis libvorbis (codec vorbis) A..... wavpack WavPack A..... wmav1 Windows Media Audio 1 A..... wmav2 Windows Media Audio 2 S..... ssa ASS (Advanced SubStation Alpha) subtitle (codec ass) S..... ass ASS (Advanced SubStation Alpha) subtitle S..... dvbsub DVB subtitles (codec dvb_subtitle) S..... dvdsub DVD subtitles (codec dvd_subtitle) S..... mov_text 3GPP Timed Text subtitle S..... srt SubRip subtitle (codec subrip) S..... subrip SubRip subtitle S..... text Raw text subtitle S..... webvtt WebVTT subtitle S..... xsub DivX subtitles (XSUB) Also uploading one of the cameras config. The other 2 are exactly the same with different names. Thanks for your time camera-1.conf

Hello and thanks for your work. It saved my a bit of space on my small NAS. Now i have some failures on 68 of the 250~ movies. All of them fail from the 1st second. Most of them is giving the following error: [mov,mp4,m4a,3gp,3g2,mj2 @ 0x55a4573da140] stream 0, timescale not set Input #0, mov,mp4,m4a,3gp,3g2,mj2, from '/library/tv/Man of Steel (2013)/Man of Steel (2013) Bluray-1080p.mp4': Metadata: major_brand : isom minor_version : 1 compatible_brands: isomavc1iso2 creation_time : 2015-11-26T19:59:29.000000Z iTunEXTC : mpaa|PG-13|300| iTunMOVI : <?xml version="1.0" encoding="UTF-8"?> : <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> : <plist version="1.0"> : <dict> : <key>cast</key> : <array> : <dict> : <key>name</key> : <string>Henry Cavill</string> : </dict> : <dict> : <key>name</key> : <string>Amy Adams</string> : </dict> : <dict> : <key>name</key> : <string>Michael Shannon</string> : </dict> : <dict> : <key>name</key> : <string>Kevin Costner</string> : </dict> : <dict> : <key>name</key> : <string>Diane Lane</string> : </dict> : <dict> : <key>name</key> : <string>Laurence Fishburne</string> : </dict> : <dict> : <key>name</key> : <string>Antje Traue</string> : </dict> : <dict> : <key>name</key> : <string>Ayelet Zurer</string> : </dict> : <dict> : <key>name</key> : <string>Christopher Meloni</string> : </dict> : <dict> : <key>name</key> : <string>Russell Crowe</string> : </dict> : </array> : <key>directors</key> : <array> : <dict> : <key>name</key> : <string>Zack Snyder</string> : </dict> : </array> : <key>producers</key> : <array> : <dict> : <key>name</key> : <string>Charles Roven</string> : </dict> : <dict> : <key>name</key> : <string>Christopher Nolan</string> : </dict> : <dict> : <key>name</key> : <string>Emma Thomas</string> : </dict> : <dict> : <key>name</key> : <string>Deborah Snyder</string> : </dict> : </array> : <key>screenwriters</key> : <array> : <dict> : <key>name</key> : <string>Christopher Nolan</string> : </dict> : <dict> : <key>name</key> : <string>David S. Goyer</string> : </dict> : </array> : </dict> : </plist> : title : Man of Steel artist : Zack Snyder genre : Action & Adventure date : 2013 synopsis : Clark Kent, one of the last of an extinguished race disguised as an unremarkable human, is forced to reveal his identity when Earth is invaded by an army of survivors who threaten to bring the planet to the brink of destruction. hd_video : 2 media_type : 9 Duration: 02:23:03.58, start: 0.000000, bitrate: 3993 kb/s Chapter #0:0: start 0.000000, end 676.967000 Metadata: title : Chapter 1 Chapter #0:1: start 676.967000, end 1201.450000 Metadata: title : Chapter 2 Chapter #0:2: start 1201.450000, end 1809.474000 Metadata: title : Chapter 3 Chapter #0:3: start 1809.474000, end 2361.609000 Metadata: title : Chapter 4 Chapter #0:4: start 2361.609000, end 2937.643000 Metadata: title : Chapter 5 Chapter #0:5: start 2937.643000, end 3543.414000 Metadata: title : Chapter 6 Chapter #0:6: start 3543.414000, end 4137.883000 Metadata: title : Chapter 7 Chapter #0:7: start 4137.883000, end 4655.108000 Metadata: title : Chapter 8 Chapter #0:8: start 4655.108000, end 5316.185000 Metadata: title : Chapter 9 Chapter #0:9: start 5316.185000, end 6047.791000 Metadata: title : Chapter 10 Chapter #0:10: start 6047.791000, end 6655.857000 Metadata: title : Chapter 11 Chapter #0:11: start 6655.857000, end 7253.579000 Metadata: title : Chapter 12 Chapter #0:12: start 7253.579000, end 7813.555000 Metadata: title : Chapter 13 Chapter #0:13: start 7813.555000, end 7969.920000 Metadata: title : Chapter 14 Chapter #0:14: start 7969.920000, end 8583.584000 Metadata: title : Chapter 15 Stream #0:0(eng): Video: h264 (avc1 / 0x31637661), yuv420p, 1920x800 [SAR 1:1 DAR 12:5], 3348 kb/s, 23.98 fps, 23.98 tbr, 24k tbn, 47.95 tbc (default) Metadata: creation_time : 2015-11-26T19:59:29.000000Z Stream #0:1(eng): Audio: ac3 (ac-3 / 0x332D6361), 48000 Hz, 5.1(side), fltp, 640 kb/s (default) Metadata: creation_time : 2015-11-26T20:01:19.000000Z handler_name : Surround Sound Side data: audio service type: main Stream #0:2(und): Data: bin_data (text / 0x74786574) Metadata: creation_time : 2015-11-26T20:06:52.000000Z Stream #0:3: Video: mjpeg, yuvj420p(pc, bt470bg/unknown/unknown), 151x227 [SAR 96:96 DAR 151:227], 90k tbr, 90k tbn, 90k tbc (attached pic) Stream mapping: Stream #0:0 -> #0:0 (h264 (native) -> hevc (libx265)) Stream #0:3 -> #0:1 (mjpeg (native) -> hevc (libx265)) Stream #0:1 -> #0:2 (ac3 (native) -> aac (native)) Stream #0:1 -> #0:3 (ac3 (native) -> aac (native)) Press [q] to stop, [?] for help [mp4 @ 0x55a45749b840] Frame rate very high for a muxer not efficiently supporting it. Please consider specifying a lower framerate, a different muxer or -vsync 2 x265 [info]: HEVC encoder version 3.2.1+1-b5c86a64bbbe x265 [info]: build info [Linux][GCC 7.5.0][64 bit] 8bit+10bit+12bit x265 [info]: using cpu capabilities: MMX2 SSE2Fast LZCNT SSSE3 SSE4.2 AVX FMA3 BMI2 AVX2 x265 [error]: Picture width must be an integer multiple of the specified chroma subsampling x265 [error]: Picture height must be an integer multiple of the specified chroma subsampling [libx265 @ 0x55a4574a0f80] Cannot open libx265 encoder. Error initializing output stream 0:1 -- Error while opening encoder for output stream #0:1 - maybe incorrect parameters such as bit_rate, rate, width or height Conversion failed! The following error lines appearing on most failed convesions [mp4 @ 0x563f63392280] Frame rate very high for a muxer not efficiently supporting it. Please consider specifying a lower framerate, a different muxer or -vsync 2 x265 [info]: HEVC encoder version 3.2.1+1-b5c86a64bbbe x265 [info]: build info [Linux][GCC 7.5.0][64 bit] 8bit+10bit+12bit x265 [info]: using cpu capabilities: MMX2 SSE2Fast LZCNT SSSE3 SSE4.2 AVX FMA3 BMI2 AVX2 x265 [error]: Picture width must be an integer multiple of the specified chroma subsampling x265 [error]: Picture height must be an integer multiple of the specified chroma subsampling [libx265 @ 0x563f633e6c80] Cannot open libx265 encoder. Error initializing output stream 0:1 -- Error while opening encoder for output stream #0:1 - maybe incorrect parameters such as bit_rate, rate, width or height Conversion failed! I have succesfuly converted the rest movies. With the exact same settings (HEVC), I would happy provide more info if you need. Uploading also unmanic.db and settings.json, it might give you some more info! unmanic.db settings.json unmanic.log

Hey, is there any chance to make it work also with docker networks? I have a chromecast on my "localdomain" network and a homeassistant docker in a "reverseproxy" network. (created with "create docker network reverseproxy") While i can ping chromecast.localdomain from homeassistant console, i doesn't appear in the devices even with manually setup. How can i repeat the mdns from one domain to another? I can't find how to setup avahi. Since pfsense doens't have access to "reverseproxy" domain

Hey i have found some qBT themes but i can't make them work. While on a windows qbt client work. I don't know how to properly install them on a dockers WebUI. Tried to put the .qbtheme file on /config/themes folder on appdata and on settings set Alternate WebUI and pointed to /config/themes/file.qbtheme After that webui wont open and gives error "Unacceptable file type, only regular file is allowed" Any suggestions? Thanks Theme tried: https://github.com/jagannatharjun/qbt-theme

Change the second adress tags to <address type='pci' domain='0x0000' bus='0x03' slot='0x00' function='0x0' multifunction='on'/> <address type='pci' domain='0x0000' bus='0x03' slot='0x00' function='0x1'/> So it will be in the same virtual bus Now you should see 2 ports when booted

Hello, i have set a Unifi Controller docker and gave it his own ip address, but i also want to make a static assignment on pfsesne. Do anyone know if dockers change mac address when they are updating or whenever? Except in the case i delete and reinstall them i guess. Is there any way to set a custom mac address? --SOLUTION-- I should do a better web search before, for anyone who might need this.. Edit container and on extra parameters add "--mac-adress 02:42:xx:xx:xx:xx" use a mac from a range of 02:42:ac:11:00:00 to 02:42:ac:11:ff:ff as this address are meant for dockers. I dont know it if works for macs out of this range

I'm having trouble syncing content to my device for offline use. I tried Xiaomi Mi 8 and Samsung S10+, Both phones can direct play any file i have on the server, but when i try to sync for offline use in ORIGINAL quaility, it keeps converting it. I tried doing this https://mostlyirrelevant.info/force-plex-to-download-sync-videos-without-transcoding/ But keeps transcoding. All my files are converted with handbrake with this profile I would accept to transcode audio, but not video. It takes a lot of time and cpu power.

I'm happy that this helped you! But i REALLY would like an explanation why it is working by doing a manually edit like this. Why the VM form creator doen't make it by it self. And how come none of the "geniuses" around here give that kind of solution. Does the auto xml creation work on others? Is this happening only on specific systems? I remember getting the exact same NIC card as SI just to avoid any problems. and also remember that i had a simillar system as SI. I'm totally noob in KVM stuff and i only figured this while i was watching a SI's video about passing a video card and he mentions about the multifunction thing. That was a lot of questions heh? SI = SpaceInvader

Only on rc5. I have Rc7 and array won't start. I did this post on reddit, you could try that to downgrade. Didn't tried it yet. So do that at your own risk https://www.reddit.com/r/unRAID/comments/erknff/downgrade_from_680_rc7_to_rc5/?utm_medium=android_app&utm_source=share

No, it have different kernel version, and array drivers so its not compatible

Hello, i'm kinda new on KVM and virtualization. And mostly new on Threadrippers. I made a build a month ago and just found out what was the cause of my unstable system (RAM XMP... ) anyway. Now its rock solid. And trying to optimize my daily driver VM and dockers with cpu pinning. I read first pages of this thread but i got more confused in the end I would really like some of your suggestions on my setup and i could give back any info/tests if you want! Mostly need help on which cores to assigned based on the CPU topology and making modifications on XML about cpu topology and ram assigment. My CPU is: Threadripper 2920x (12C24T) - GPU RX5700 8GB- 32GB Ram My setup / needs are: Well Unraid - It should be good with 2 Cores i guess, i dont have more than 2 people copying from/to array and of them is me from the VM! VMS *Windows VM for Gaming with NVME on unassigned devices(not on cache) and RX5700 (Damn Navi bug.. ) - Will run only while gaming - 6 Cores/16gb ram? Had issues on Borderlands 3 when running under 18GB Ram. Was running out of memory. *Linux VM for daily use (Not need much power and soon will have a cheap gpu passed) 2 cores/4GB Ram should be ok - Will run 24/7 - 4GB Ram should be ok *pfSense VM as router/firewall - 2 Cores/4GB Ram should be enough. - Will run 24/7 Lightweight Dockers (those should all run fine with 1 core) - dont care if the slow down, as those dockers dont do anything important. *sonarr *radarr *bazarr *tautulli *jackett *deluge *duckdns *MQTT *Home-assistant *unifi-controller Heaveweight Dockers *Handbrake - This will never run while gaming so it can be assigned the same cores as gaming vm. *Plex - All my files are x264 so not much transcoding needed. Max 3 streams concurrently and 2 of the local. CPU Pairs as taken from VM Editor of Unraid CPU 0 - HT 12 CPU 1 - HT 13 CPU 2 - HT 14 CPU 3 - HT 15 CPU 4 - HT 16 CPU 5 - HT 17 CPU 6 - HT 18 CPU 7 - HT 19 CPU 8 - HT 20 CPU 9 - HT 21 CPU 10 - HT 22 CPU 11 - HT 23 Thanks! If i should add more info, please tell me what is this you need!

<hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0b' slot='0x00' function='0x0'/> </source> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0' multifunction='on'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0b' slot='0x00' function='0x1'/> </source> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x1'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0c' slot='0x00' function='0x0'/> </source> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0' multifunction='on'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0c' slot='0x00' function='0x1'/> </source> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x1'/> </hostdev> Here is how my XML is now and pfsense sees all 4 ports Here is my IOMMU IOMMU group 18: [111d:8018] 0a:02.0 PCI bridge: Microsemi / PMC / IDT PES12N3A 12-lane 3-Port PCI Express Switch (rev 0e) [8086:10bc] 0b:00.0 Ethernet controller: Intel Corporation 82571EB/82571GB Gigabit Ethernet Controller (Copper) (rev 06) [8086:10bc] 0b:00.1 Ethernet controller: Intel Corporation 82571EB/82571GB Gigabit Ethernet Controller (Copper) (rev 06) IOMMU group 19: [111d:8018] 0a:04.0 PCI bridge: Microsemi / PMC / IDT PES12N3A 12-lane 3-Port PCI Express Switch (rev 0e) [8086:10bc] 0c:00.0 Ethernet controller: Intel Corporation 82571EB/82571GB Gigabit Ethernet Controller (Copper) (rev 06) [8086:10bc] 0c:00.1 Ethernet controller: Intel Corporation 82571EB/82571GB Gigabit Ethernet Controller (Copper) (rev 06) I dont know what else you could try. ill leave it to the pros.

<hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x07' slot='0x00' function='0x0'/> </source> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x0'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x07' slot='0x00' function='0x1'/> </source> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x1'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x08' slot='0x00' function='0x0'/> </source> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x2'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x08' slot='0x00' function='0x1'/> </source> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x3'/> </hostdev> This should work now. I just tricked it to see the whole nic as one pci device and multiple functions. It was one of the ways that worked for me. Haven't tested yet neither setting pfsense or speed. but this made mine show up

Try changing the guest address so both pci devices are on the same bus - same slot Add multifunction on the 1st device and change the second device to function 0x1 Same on the 3rd and 4th just change bus number. Each pair should be on one bus. Just copy paste this over your XML for those 4 devices. Should work. DISCLAIMER! I don't know if its the right way to do this. But this was what fixed it for me! I have very small idea on what i'm doing in KVM! <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x07' slot='0x00' function='0x0'/> </source> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x0' multifunction='on'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x07' slot='0x00' function='0x1'/> </source> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x1'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x08' slot='0x00' function='0x0'/> </source> <address type='pci' domain='0x0000' bus='0x04' slot='0x00' function='0x0' multifunction='on'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x08' slot='0x00' function='0x1'/> </source> <address type='pci' domain='0x0000' bus='0x04' slot='0x00' function='0x1'/> </hostdev>

Can I use this kernel if I have updated to rc7?

I'll test in the week how it works. hopefully will go well.

I'm not chaning the host pci address, im changing the guest pci address! NIC is HP NC364T (the same SI is using) IOMMU groups IOMMU group 0: [1022:1452] 00:01.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 1: [1022:1453] 00:01.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) PCIe GPP Bridge IOMMU group 2: [1022:1453] 00:01.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) PCIe GPP Bridge IOMMU group 3: [1022:1453] 00:01.3 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) PCIe GPP Bridge IOMMU group 4: [1022:1452] 00:02.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 5: [1022:1452] 00:03.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 6: [1022:1453] 00:03.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) PCIe GPP Bridge IOMMU group 7: [1022:1452] 00:04.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 8: [1022:1452] 00:07.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 9: [1022:1454] 00:07.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Internal PCIe GPP Bridge 0 to Bus B IOMMU group 10: [1022:1452] 00:08.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 11: [1022:1454] 00:08.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Internal PCIe GPP Bridge 0 to Bus B IOMMU group 12: [1022:790b] 00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 59) [1022:790e] 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 51) IOMMU group 13: [1022:1460] 00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 0 [1022:1461] 00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 1 [1022:1462] 00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 2 [1022:1463] 00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 3 [1022:1464] 00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 4 [1022:1465] 00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 5 [1022:1466] 00:18.6 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 6 [1022:1467] 00:18.7 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 7 IOMMU group 14: [1022:1460] 00:19.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 0 [1022:1461] 00:19.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 1 [1022:1462] 00:19.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 2 [1022:1463] 00:19.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 3 [1022:1464] 00:19.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 4 [1022:1465] 00:19.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 5 [1022:1466] 00:19.6 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 6 [1022:1467] 00:19.7 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Data Fabric: Device 18h; Function 7 IOMMU group 15: [1022:43ba] 01:00.0 USB controller: Advanced Micro Devices, Inc. [AMD] X399 Series Chipset USB 3.1 xHCI Controller (rev 02) [1022:43b6] 01:00.1 SATA controller: Advanced Micro Devices, Inc. [AMD] X399 Series Chipset SATA Controller (rev 02) [1022:43b1] 01:00.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] X399 Series Chipset PCIe Bridge (rev 02) [1022:43b4] 02:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) [1022:43b4] 02:01.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) [1022:43b4] 02:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) [1022:43b4] 02:03.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) [1022:43b4] 02:04.0 PCI bridge: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset PCIe Port (rev 02) [8086:1539] 04:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network Connection (rev 03) [8086:24fd] 05:00.0 Network controller: Intel Corporation Wireless 8265 / 8275 (rev 78) [8086:1539] 06:00.0 Ethernet controller: Intel Corporation I211 Gigabit Network Connection (rev 03) IOMMU group 16: [144d:a808] 08:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM981/PM981/PM983 IOMMU group 17: [111d:8018] 09:00.0 PCI bridge: Microsemi / PMC / IDT PES12N3A 12-lane 3-Port PCI Express Switch (rev 0e) IOMMU group 18: [111d:8018] 0a:02.0 PCI bridge: Microsemi / PMC / IDT PES12N3A 12-lane 3-Port PCI Express Switch (rev 0e) [8086:10bc] 0b:00.0 Ethernet controller: Intel Corporation 82571EB/82571GB Gigabit Ethernet Controller (Copper) (rev 06) [8086:10bc] 0b:00.1 Ethernet controller: Intel Corporation 82571EB/82571GB Gigabit Ethernet Controller (Copper) (rev 06) IOMMU group 19: [111d:8018] 0a:04.0 PCI bridge: Microsemi / PMC / IDT PES12N3A 12-lane 3-Port PCI Express Switch (rev 0e) [8086:10bc] 0c:00.0 Ethernet controller: Intel Corporation 82571EB/82571GB Gigabit Ethernet Controller (Copper) (rev 06) [8086:10bc] 0c:00.1 Ethernet controller: Intel Corporation 82571EB/82571GB Gigabit Ethernet Controller (Copper) (rev 06) IOMMU group 20: [10de:0640] 0d:00.0 VGA compatible controller: NVIDIA Corporation G96C [GeForce 9500 GT] (rev a1) IOMMU group 21: [1022:145a] 0e:00.0 Non-Essential Instrumentation [1300]: Advanced Micro Devices, Inc. [AMD] Zeppelin/Raven/Raven2 PCIe Dummy Function IOMMU group 22: [1022:1456] 0e:00.2 Encryption controller: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Platform Security Processor IOMMU group 23: [1022:145f] 0e:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Zeppelin USB 3.0 Host controller IOMMU group 24: [1022:1455] 0f:00.0 Non-Essential Instrumentation [1300]: Advanced Micro Devices, Inc. [AMD] Zeppelin/Renoir PCIe Dummy Function IOMMU group 25: [1022:7901] 0f:00.2 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 51) IOMMU group 26: [1022:1457] 0f:00.3 Audio device: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) HD Audio Controller IOMMU group 27: [1022:1452] 40:01.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 28: [1022:1452] 40:02.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 29: [1022:1452] 40:03.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 30: [1022:1453] 40:03.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) PCIe GPP Bridge IOMMU group 31: [1022:1452] 40:04.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 32: [1022:1452] 40:07.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 33: [1022:1454] 40:07.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Internal PCIe GPP Bridge 0 to Bus B IOMMU group 34: [1022:1452] 40:08.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-1fh) PCIe Dummy Host Bridge IOMMU group 35: [1022:1454] 40:08.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Internal PCIe GPP Bridge 0 to Bus B IOMMU group 36: [1002:1478] 41:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] Device 1478 (rev c4) IOMMU group 37: [1002:1479] 42:00.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] Device 1479 IOMMU group 38: [1002:731f] 43:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 [Radeon RX 5700 / 5700 XT] (rev c4) IOMMU group 39: [1002:ab38] 43:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Navi 10 HDMI Audio IOMMU group 40: [1022:145a] 44:00.0 Non-Essential Instrumentation [1300]: Advanced Micro Devices, Inc. [AMD] Zeppelin/Raven/Raven2 PCIe Dummy Function IOMMU group 41: [1022:1456] 44:00.2 Encryption controller: Advanced Micro Devices, Inc. [AMD] Family 17h (Models 00h-0fh) Platform Security Processor IOMMU group 42: [1022:145f] 44:00.3 USB controller: Advanced Micro Devices, Inc. [AMD] Zeppelin USB 3.0 Host controller IOMMU group 43: [1022:1455] 45:00.0 Non-Essential Instrumentation [1300]: Advanced Micro Devices, Inc. [AMD] Zeppelin/Renoir PCIe Dummy Function IOMMU group 44: [1022:7901] 45:00.2 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 51)

Hello. i'm trying to passthrou my 4 port NIC to pfsense VM. I have followed SI's video I have stubbed the NIC and it appears on the VM editor. I'm selecting all 4 ports and boot the VM. pfSense only sees 1 port. (em0). The only way i managed to make pfSense to see all 4 ports was to manually change XML to this: By changing guest nic's addresses to: 01:00.0 01:00.1 01:00.2 01:00.3 from 01:00.0 03:00.0 04:00.0 05:00.0 Is this correct way to do it? Why with the default XML it only lists 1 port? Edited XML Part: <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0b' slot='0x00' function='0x0'/> </source> <alias name='hostdev0'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x0'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0b' slot='0x00' function='0x1'/> </source> <alias name='hostdev1'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x1'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0c' slot='0x00' function='0x0'/> </source> <alias name='hostdev2'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x2'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0c' slot='0x00' function='0x1'/> </source> <alias name='hostdev3'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x3'/> </hostdev> auto generated XML. <?xml version='1.0' encoding='UTF-8'?> <domain type='kvm' id='15'> <name>pfSense</name> <uuid>333adf90-ea87-2912-7ae3-1e2915df94c0</uuid> <metadata> <vmtemplate xmlns="unraid" name="FreeBSD" icon="pfsense.png" os="freebsd"/> </metadata> <memory unit='KiB'>4194304</memory> <currentMemory unit='KiB'>4194304</currentMemory> <memoryBacking> <nosharepages/> </memoryBacking> <vcpu placement='static'>4</vcpu> <cputune> <vcpupin vcpu='0' cpuset='10'/> <vcpupin vcpu='1' cpuset='22'/> <vcpupin vcpu='2' cpuset='11'/> <vcpupin vcpu='3' cpuset='23'/> </cputune> <resource> <partition>/machine</partition> </resource> <os> <type arch='x86_64' machine='pc-q35-4.1'>hvm</type> <loader readonly='yes' type='pflash'>/usr/share/qemu/ovmf-x64/OVMF_CODE-pure-efi.fd</loader> <nvram>/etc/libvirt/qemu/nvram/333adf90-ea87-2912-7ae3-1e2915df94c0_VARS-pure-efi.fd</nvram> </os> <features> <acpi/> <apic/> </features> <cpu mode='host-passthrough' check='none'> <topology sockets='1' cores='4' threads='1'/> </cpu> <clock offset='utc'> <timer name='rtc' tickpolicy='catchup'/> <timer name='pit' tickpolicy='delay'/> <timer name='hpet' present='no'/> </clock> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/local/sbin/qemu</emulator> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/mnt/user/isos/Linux/pfSense-CE-2.4.4-RELEASE-p3-amd64.iso'/> <backingStore/> <target dev='hda' bus='sata'/> <readonly/> <boot order='2'/> <alias name='sata0-0-0'/> <address type='drive' controller='0' bus='0' target='0' unit='0'/> </disk> <disk type='file' device='disk'> <driver name='qemu' type='qcow2' cache='writeback'/> <source file='/mnt/user/domains/pfSense/vdisk1.img'/> <backingStore/> <target dev='hdc' bus='sata'/> <boot order='1'/> <alias name='sata0-0-2'/> <address type='drive' controller='0' bus='0' target='0' unit='2'/> </disk> <controller type='pci' index='0' model='pcie-root'> <alias name='pcie.0'/> </controller> <controller type='pci' index='1' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='1' port='0x10'/> <alias name='pci.1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0' multifunction='on'/> </controller> <controller type='pci' index='2' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='2' port='0x11'/> <alias name='pci.2'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x1'/> </controller> <controller type='pci' index='3' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='3' port='0x12'/> <alias name='pci.3'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x2'/> </controller> <controller type='pci' index='4' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='4' port='0x13'/> <alias name='pci.4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x3'/> </controller> <controller type='pci' index='5' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='5' port='0x14'/> <alias name='pci.5'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x4'/> </controller> <controller type='pci' index='6' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='6' port='0x15'/> <alias name='pci.6'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x5'/> </controller> <controller type='pci' index='7' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='7' port='0x16'/> <alias name='pci.7'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x6'/> </controller> <controller type='pci' index='8' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='8' port='0x17'/> <alias name='pci.8'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x7'/> </controller> <controller type='pci' index='9' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='9' port='0x18'/> <alias name='pci.9'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0' multifunction='on'/> </controller> <controller type='pci' index='10' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='10' port='0x19'/> <alias name='pci.10'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x1'/> </controller> <controller type='pci' index='11' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='11' port='0x1a'/> <alias name='pci.11'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x2'/> </controller> <controller type='pci' index='12' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='12' port='0x1b'/> <alias name='pci.12'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x3'/> </controller> <controller type='virtio-serial' index='0'> <alias name='virtio-serial0'/> <address type='pci' domain='0x0000' bus='0x02' slot='0x00' function='0x0'/> </controller> <controller type='sata' index='0'> <alias name='ide'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x1f' function='0x2'/> </controller> <controller type='usb' index='0' model='ich9-ehci1'> <alias name='usb'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x7'/> </controller> <controller type='usb' index='0' model='ich9-uhci1'> <alias name='usb'/> <master startport='0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0' multifunction='on'/> </controller> <controller type='usb' index='0' model='ich9-uhci2'> <alias name='usb'/> <master startport='2'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x1'/> </controller> <controller type='usb' index='0' model='ich9-uhci3'> <alias name='usb'/> <master startport='4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x2'/> </controller> <serial type='pty'> <source path='/dev/pts/2'/> <target type='isa-serial' port='0'> <model name='isa-serial'/> </target> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/2'> <source path='/dev/pts/2'/> <target type='serial' port='0'/> <alias name='serial0'/> </console> <channel type='unix'> <source mode='bind' path='/var/lib/libvirt/qemu/channel/target/domain-15-pfSense/org.qemu.guest_agent.0'/> <target type='virtio' name='org.qemu.guest_agent.0' state='disconnected'/> <alias name='channel0'/> <address type='virtio-serial' controller='0' bus='0' port='1'/> </channel> <input type='tablet' bus='usb'> <alias name='input0'/> <address type='usb' bus='0' port='1'/> </input> <input type='mouse' bus='ps2'> <alias name='input1'/> </input> <input type='keyboard' bus='ps2'> <alias name='input2'/> </input> <graphics type='vnc' port='5900' autoport='yes' websocket='5700' listen='0.0.0.0' keymap='en-us'> <listen type='address' address='0.0.0.0'/> </graphics> <video> <model type='qxl' ram='65536' vram='65536' vgamem='16384' heads='1' primary='yes'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x0'/> </video> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0b' slot='0x00' function='0x0'/> </source> <alias name='hostdev0'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x0'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0b' slot='0x00' function='0x1'/> </source> <alias name='hostdev1'/> <address type='pci' domain='0x0000' bus='0x03' slot='0x00' function='0x0'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0c' slot='0x00' function='0x0'/> </source> <alias name='hostdev2'/> <address type='pci' domain='0x0000' bus='0x04' slot='0x00' function='0x0'/> </hostdev> <hostdev mode='subsystem' type='pci' managed='yes'> <driver name='vfio'/> <source> <address domain='0x0000' bus='0x0c' slot='0x00' function='0x1'/> </source> <alias name='hostdev3'/> <address type='pci' domain='0x0000' bus='0x05' slot='0x00' function='0x0'/> </hostdev> <memballoon model='none'/> </devices> <seclabel type='dynamic' model='dac' relabel='yes'> <label>+0:+100</label> <imagelabel>+0:+100</imagelabel> </seclabel> </domain>

Hey! How is the patch acting? Does it work well? Thanks!