King908 Posted June 30, 2022 Share Posted June 30, 2022 Hey all, Well I did it, I upgraded from 6.9.2 to 6.10.3 and as expected it didn't go properly. I am getting Array Stopped - Stale Configuration when I start the array. My VM's are running, and my Dockers are running, but UnRaid only gives me a reboot or shutdown. I closed my brower, and even did a reboot, no issues until I start the array. I tried Safari browser even and same issue. Not sure where to go from here to clear this issue. I made 0 configuration changes and the only changes right before upgrade was Docker and Plugin updates. Appreciate any support. Thank you all. unraidsvr-diagnostics-20220630-1024.zip Quote Link to comment
JorgeB Posted June 30, 2022 Share Posted June 30, 2022 This error basically means the GUI is out of sync with the array, but it's not always clear the root cause, make sure no other browser windows are open on the GUI, reset cookies or try a different browser and also try booting in safe mode. Quote Link to comment
BelgarionNL Posted July 1, 2022 Share Posted July 1, 2022 exactly the same error. also from 6.9.2 to 6.10.3 so far I havent been able to resolve it. Quote Link to comment
Acps Posted July 1, 2022 Share Posted July 1, 2022 I remember struggling with this, are you trying both http/https? I was using firefox and it would have a box that popped up each time it was stale. Here was my post about it: https://forums.unraid.net/topic/121459-unraid-stable-until-rebootrestart-then-may-fail-to-boot/?do=findComment&comment=1109476 this was the error that happened with the stale config I eventually got it fixed, but im terrible at documenting what I did to fix it. Hope this helps some! Quote Link to comment
JorgeB Posted July 2, 2022 Share Posted July 2, 2022 Either of the posters above with the issue can you please confirm that booting in safe mode didn't help? Quote Link to comment
azacan Posted August 9, 2022 Share Posted August 9, 2022 Happened to me following same upgrade path and using Firefox. I got it solved, as mentioned here, by rebooting the system (no need of safe mode) and doing the first log in with a different browser, not Firefox. I tried Brave (based on Chrome) and everything went fine. Quote Link to comment
Georgie Posted September 28, 2022 Share Posted September 28, 2022 On 7/2/2022 at 10:52 AM, JorgeB said: Either of the posters above with the issue can you please confirm that booting in safe mode didn't help? I just found this post because I'm having the same exact problem as Acps, after upgrading from 6.10.3 to 6.11.0 I can confirm that I tried booting in safe mode, then booting in regular mode and I'm still having the same issue Quote Link to comment
Solution JorgeB Posted September 28, 2022 Solution Share Posted September 28, 2022 Are you using Firefox? Quote Link to comment
Georgie Posted October 1, 2022 Share Posted October 1, 2022 On 9/28/2022 at 2:24 AM, JorgeB said: Are you using Firefox? Yes, I was using firefox, ultimately I solved the problem in the same way that azacan did, I rebooted the system and did a login with a different browser (chrome, in my case): On 8/9/2022 at 4:25 PM, azacan said: Happened to me following same upgrade path and using Firefox. I got it solved, as mentioned here, by rebooting the system (no need of safe mode) and doing the first log in with a different browser, not Firefox. I tried Brave (based on Chrome) and everything went fine. 1 Quote Link to comment
Voetentje Posted November 20, 2022 Share Posted November 20, 2022 Firefox user and had the same problem, rebooting and doing the first login in Edge also solved the issue for me. 1 Quote Link to comment
bulbousFruitfly Posted December 13, 2022 Share Posted December 13, 2022 ran into this today: upgraded from v6.9.2 to v6.11.5 - after the reboot and before I started the array (all existing disks showed healthy), I shut down the server to add a new disk. Booted back up, new disk was found and assigned - started the array and disk preclear was in progress. Came back a few hours later, disk preclear was at ~60%, the array was stopped and the only error message I could find in the log was "unraid emhttpd: stale configuration". Array control buttons were gone - I could only reboot or shutdown the server. Was using Firefox v107.0.1 Rebooted and logged back in using MS Edge - all disks showed green and preclear was restarted at 0%, but I could start the array and everything is now still fine even when coming back using Firefox. Quote Link to comment
denellum Posted January 2, 2023 Share Posted January 2, 2023 (edited) On 12/13/2022 at 5:15 PM, bulbousFruitfly said: ran into this today: upgraded from v6.9.2 to v6.11.5 - after the reboot and before I started the array (all existing disks showed healthy), I shut down the server to add a new disk. Booted back up, new disk was found and assigned - started the array and disk preclear was in progress. Came back a few hours later, disk preclear was at ~60%, the array was stopped and the only error message I could find in the log was "unraid emhttpd: stale configuration". Array control buttons were gone - I could only reboot or shutdown the server. Was using Firefox v107.0.1 Rebooted and logged back in using MS Edge - all disks showed green and preclear was restarted at 0%, but I could start the array and everything is now still fine even when coming back using Firefox. Just had this happened, scared the crap out of me. This resolved it for me as well! Thank you for your help Edited January 2, 2023 by denellum Quote Link to comment
itimpi Posted January 2, 2023 Share Posted January 2, 2023 On 12/13/2022 at 11:15 PM, bulbousFruitfly said: started the array and disk preclear was in progress A small point on terminology - this is a Clear and not a preClear. A Preclear is when you clear the drive BEFORE adding it to the array. I agree that is a bit pedantic but it does avoid possible confusion as to what is happening. 1 Quote Link to comment
pinion Posted March 20, 2023 Share Posted March 20, 2023 Had this issue today 6.11.5. I didn't upgrade but I was trying to add a drive to my array. And yes, using firefox. Working ok in chrome mobile. Firefox needs some lovin! Quote Link to comment
EDACerton Posted April 6, 2023 Share Posted April 6, 2023 I get the same issue on 6.12.0-rc2. It happens any time that I start the array -- once the array starts, I get the Firefox "resubmit form data" popup. If I tell it to resubmit, I get "stale configuration". If I tell it not to resubmit, everything continues as normal. 1 Quote Link to comment
unraidster Posted April 6, 2023 Share Posted April 6, 2023 (edited) Hi, I just encountered the same issue (within a lab which is running 6.11.5). Using Firefox 111.01 i get the same issue of start array > prompt > hit resubmit > stale configuration. Note: I was previously able to login to this server without this issue, cannot recall what version of Firefox I was running when i last accessed this server. Signing in via the Edge browser seems to work without such a prompt. I have attached a screenshot of the dialog. The workaround (clicking on cancel in the prompt) isn't too difficult to do but would be good to understand the root cause. I have included some diagnostics if they are of use to anyone. (captured after attempting to login via Firefox and clicking on resubmit on the dialog). Thanks, ++ Tried on 6.9.2 with the same version of Firefox and not seeing the same issue. ur-lab-diagnostics-20230406-1041.zip Edited April 6, 2023 by unraidster Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.