Acps

Disk 4 of my array has been kicked offline several times the past several weeks. Each time I was able to run clean short/long smart checks and rebuild my array. The disk is only a couple months old, and didnt start having issues until it got filled up with data. Can someone take a look at my syslogs and let me know what they think? Thanks in advance ~Acps unraid-diagnostics-20231014-2231.zip

Ty, fixxed my issues with naming!

Over the weekend I was able to successfully unassign disk4 and rebuild pairty2. Ran another extended smart test on disk 4 and it completed with read failure again. My replacement drive should be arriving this week. I ran a parity check after my parity rebuild, which also completed with 0 errors. But now parity 2 is disabled again after having many read errors. I have most dockers turned off right now, save Plex. Attached my diags and will run an extended smart test on parity2 overnight, is it likely I have another disk going bad? Parity2 is only 2 years old, while disk 4 is 8 years. Appreciate any help! Ty in advance ~Acps unraid-diagnostics-20230221-1827.zip

I likely won't have a replacement for disk 4 for several days. Can I reassign Parity2 and leave disk 4 unassigned to rebuild that disk? Or do both disks need to be assigned together? I've been wanting to replace my 4-5tb drives with 8tb cmr, likely ST8000VNZ04. -Acps Sent from my iPhone using Tapatalk

The gui was acting like the array was read/writing at 160Mbs, however it never moved passed 0% at 1.97gb after 2 hours. I wasnt able to pause or cancel the rebuild, however I was able to do a powerdown -r, to get the system rebooted and powered down. Server is off site and I plan on grabbing it after work today to work on it this weekend. Snagged the diag after reboot. I also should have nearly 99% of all my syslogs going back atleast to 2021. Any input and how to go recover parity2 while i replaced disk 4 so i dont botch it 😁 unraid-diagnostics-20230217-1323.zip

How do I stop the data-rebuild. The menu buttons are not responding. Will Parity 2 need to be rebuilt too, aka unassigned and reassigned too? Also do I want to leave disk 4 disabled for now or just unassign the bad drive until I order a replacement? -Acps Sent from my iPhone using Tapatalk

I have been having issues with moving large amounts of data from my cache drives to the array for the last several months. Started shortly after doubling my ram from 2 to 4 sticks. Today I thought I would remove 2 ram sticks to see if the disk errors would clear up. However I clearly botched what I thought was a simple task into a possible data loss incident? 🤕 I'll attach my logs and hope someone could take a look and help me try and dig myself out of this pickle im in now. Ty in advance ~Acps unraid-diagnostics-20230217-1149.zip

I am most certainly did something like that not thinking it would be an issue. I just put a new psu to replace the smaller one last year. This is what I got: https://a.co/d/92aY6Vr And I have tons of cables for the mods and bags of splitters. So all 8 array disks are mounted in 2 racks right above my psu. All 8 disks are connected to my 9300-8i card on my pcie x16 slot. Also would moving both Parity drives off the lsi card and switch them to the onboard sata 3 controller be a good idea? Ty ~Acps

IS there anything else i can try to do to confirm its the mobo? Is it possible to get any infornmation/logs from the bios during boot to see what is having issues?

I was considering that too because of all the issues in have had with it. But I always was able to get it booting again at the end of the day and usually when it gets running I have 0 issues. Any chance it could be a power issue? I really don't know how much a hard disk consumes on a power scale. I don't know if I paid attention to how I was drawing power from the cables. Can 8 drives on the same port from the psu draw enough power to cause any issues? Sent from my iPhone using Tapatalk

As a result my mover is struggling to get things off my cache and onto the array, it has been running for 4 hours and is only half way:

So for several months I dodged this issues by moving my lsi card to another pci slot that wasnt x16, i wanted to tackle it again and worked on it a bit this week, i found that I was able to stop my bios from hanging and not posting by deleting the LSI bios rom on my card, leaving just the IT firmware on it. So i no longer need to worry about it hanging if i reboot it remotly. However I still struggling with my lsi card and booting with my disks are still 50/50. I believe it has to do with my bios setting pcie gen set to auto. My card is in the top pcie slot which is def x16. But it never shows after boot that my link speed is ever at pcie3, its always at pcie1. If i go and mess with the bios and try to manual set the pcie speed to gen 3, my disks never boot. If i leave it to auto it will usually boot without disks the first time, im guessing cause it tried to do pcie3, and if i reboot without touching the bios, it boots with the disks in pcie1. Right now i figured that i can manually set the pcie2 in the bios and it seems to come up with my drives. I have both parity and every array disk on the controller, and my ssd/caches using the onboard sata ahci controller. Btw the cache drives boot 100% every time. I have run out of ides though, do i have a hardware issues or is this a bios setting i seem to be overlooking? I have reset to default and it hasnt helped. I will attach some diag, one will be when the drives failed to boot and the other when the drives do boot. If anyone could take a look I would appreciate it! ~Acps unraid-diagnostics-20220715-1359-nodisks.zipunraid-diagnostics-20220715-1439-yesdisks.zip

So I got a fresh usb and my key moved to a fresh build. the only configurations i did, was network settings and installed myservers. Is this what I need to see before pressing start for the first time? Disk 6 was reporting an error: Is there anything I should do before trying to do a parity sync? Ty in advance! ~Acps

Gonna post my diagnostics file, just to make sure I am not making my situation worse first! 🤣 unraid-diagnostics-20220702-1105.zip There isnt anything in my appdata/cache that i dont have backedup in the event I might want to recover it.

I have backups of my flash drive with syslogs and such. Can I just install unraid on a new usb and copy the disk config only? My parity disks are the only 8tb disks in my array right now, so thats easy to keep track of. But if its that easy as assigning them in this order, it sounds simple. Maybe too simple

I remember struggling with this, are you trying both http/https? I was using firefox and it would have a box that popped up each time it was stale. Here was my post about it: https://forums.unraid.net/topic/121459-unraid-stable-until-rebootrestart-then-may-fail-to-boot/?do=findComment&comment=1109476 this was the error that happened with the stale config I eventually got it fixed, but im terrible at documenting what I did to fix it. Hope this helps some!

So Id like to start from scratch with my unRaid, with the exception of the data on my array of course. Over the last 8 years I think I have made enough undocumented changes that id like the start from scratch with all settings and rebuild my cache/flash drive from scratch. Is there a safe way to reset to default settings? So that I preserve only the data on my array and simply flush the rest to default? Thanks in advance! ~Acps

Couple other things that are happening now: Server no longer accessible by https://unraid/ It instead returns a white page with an error 404 Not Found - nginx Using http://unraid/ does work and looks to be using ssl too. Using static ip instead of hostname doesnt help. After starting successfully starting array, Array while change on the Main tab to say Array Stopped - Stale Configuration Dockers are still running and usable, and shares are available however... another diag unraid-diagnostics-20220322-1420.zip ~Acps

My unraid server has been having many issues whenever a reboot is performed. I put in a LSI SAS 9300-8i in Mar 2021 to replace an older card that was suspest of failing due to erratic read/write speeds , anytime i power cycle my system, theres a good chance that something goes wrong, like not reaching post and stuck at the blinking cursor, other times its bios fault 10h encountered at adapter pcI(01h,00h,00h) which is the lsi card slot, other times itll be the that lsi card is recognized and boot to gui but all array drives are missing but cache/flash are online. Simply rebooting my system, sometimes several times if needed, until it doesnt encounter any of these errors, I will be able to start array, and it will run without any issue for weeks/months. I put up my diagnostics and and the last 2 months of syslogs captured whenver a reboot is done to try and get as much info about whats been going on, syslogs saved on usb go back several years, but not sure if thats helpful. Can anyone take a peek and provide any advice? Im hoping its simple like a bad usb drive? Most of my configuartion has been replaced at somepoint since put together in 2015, including disks, controller card, every cable for all drives, water cooler was added and psu replaced. most of which has been in the last 1-2 years. What hasnt been replaced is the cpu/motherboard/ram. And its on 24/7 for the most part for the last 7 years. Thanks in advance for the help again! ~Acps logs.rar unraid-diagnostics-20220321-1947.zip

Hey there, I did not find anything that helped. Other than filling up the system log though, I don't think it has any impact on the ups being able to do its job because it's still able to communicate with the ups and the gui shows it reporting the battery level, load and runtime left. I guess if you really wanted to be cautious you could disconnect most of your drives in your Nas and just boot unraid from the usb and unplug the ups from the wall and monitor the gui to see if it functions correctly and iniates shutdown at the proper % you have set. Other than filling up the system log which is rather annoying, it's might be easier to keep it from reporting the errors to begin with, but isn't something that I have looked at yet. Which may or may not be a good idea! -Acps Sent from my iPhone using Tapatalk

any news for updating to unraid 6.10? mine can discover the server in the app but cannot connect

Swapped out and older apc for a new CyberPower CP1000PFCLCD, however i keep getting this error in the syslog: unRaid usbhid-ups[18476]: nut_libusb_get_report: Input/Output Error. I tried moving the cable to several different usb ports and it was the same thing, do i have a cable or ups issue going on? unraid-syslog-20211005-0126.zip

Installed my LSI 9300-8i and it did wonders! Havent had any issues with the array since installed! TY @JorgeB

i just went ahead and pulled the trigger on a LSI 9300-8i, will be here next week 😅

I dont, i have been using it for 7 years. I guess i should just replace it at this point, iv seem to had alot of issues with it