squirrellydw

Hey Influencer, any chance you could start a new thread with your plug-in so we can keep everything under one place? I want to try and do this in a few days after you add more things to it and update it more but following 2 or 3 threads is getting a bit confusing. I paid for the plus version but can't seem to download it, any idea? The link in the email isn't doing anything.

So any chance of making this into a plug-in? Also I know it's probably too early to tell but how does this compare to newzbin, nzbmatrix and others?

this sucks

Rebooted and it's working now, thanks Joe

There is nothing under those settings, I will reboot and see what happens and report back in a few days when I add more shows. Thanks for the tip Joe.

I recently added my old parity drive to the array as a data drive, disk6. Under share settings for TV Shows I added it as disk6 with Allocation as high water however nothing has been added to it. My other drives disk1 and disk4 are starting to get full so I thought the new tv shows should go to disk6, any idea? Disk1 as about 60GB left, Disk4 about 218GB and Disk6 is a 2TB

I just assigned my old 2TB parity drive to be a data drive, how long till unraid comes back up? I didn't think I had to preclear it but unraid says it's clearing it.

yes. Then, once the initial calculations are written to the parity drive you must then perform a manual parity check to ensure what you've written can be read. Finally, you must look at the SMART report for that drive to see if any sectors are pending re-allocation because they cannot be read. Joe L. So I ran the manual parity check and no errors were found so that good. Here is m smart report, looks OK to me what do you think? Statistics for /dev/sdi ST3000DM001-1CH166_W1F1N8ZG smartctl -a -d ata /dev/sdi smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST3000DM001-1CH166 Serial Number: W1F1N8ZG Firmware Version: CC24 User Capacity: 3,000,592,982,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Tue Dec 4 21:09:24 2012 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 97) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 115 100 006 Pre-fail Always - 89306608 3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 5 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always - 979917 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 93 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 4 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 088 088 000 Old_age Always - 12 190 Airflow_Temperature_Cel 0x0022 074 068 045 Old_age Always - 26 (Min/Max 20/30) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 4 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 18 194 Temperature_Celsius 0x0022 026 040 000 Old_age Always - 26 (0 19 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 112936165048404 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 23443981768 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 52198843707 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 93 - # 2 Short offline Completed without error 00% 93 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

Thanks Joe, any chance you could post a report of excatly what I should be look for each time and what they mean?

Thanks Joe, I only need to look at this part correct? sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 2. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 2. 0 sectors were pending re-allocation after post-read in cycle 1 of 2. 0 sectors were pending re-allocation after zero of disk in cycle 2 of 2. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change.

anyone??

Just replaced my parity drive with a larger one, I need to hit "Sync" to start the parity sync correct?

thanks Benni, I guess I need to run another cable. Looks like a project for after Christmas.

So I have a supermicro board that supports IPMI but I have no idea how to use it, anyone care to help explain this to me? I have a Mac but can run Windows programs if I have to. Do I have to install any software on the server and do anything in the BIOS or do I just need to install IPMIVIEW on my Mac Laptop? Thanks for any help

Can some verify that everything looks good? ** Changed attributes in files: /tmp/smart_start_sdi /tmp/smart_finish_sdi ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Raw_Read_Error_Rate = 115 118 6 ok 98284504 Spin_Retry_Count = 100 100 97 near_thresh 0 End-to-End_Error = 100 100 99 near_thresh 0 High_Fly_Writes = 96 98 0 ok 4 Airflow_Temperature_Cel = 72 74 45 ok 28 Temperature_Celsius = 28 26 0 ok 28 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 2. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 2. 0 sectors were pending re-allocation after post-read in cycle 1 of 2. 0 sectors were pending re-allocation after zero of disk in cycle 2 of 2. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change. root@Tower:/boot#

Just FYI, this should work for you : ftp://ftp.supermicro.com/utility/IPMIView/ (I seem to remember it wasn't obvious to find when I originally looked). So to use screen I just type in telnet like I usually would then cd /boot, screen, then I hit space bar correct? The link to IPMIVIEW is asking for a password

thank you , that worked

How do I find my profile file and does this work with terminal?

Yeah I have an ipmi motherboard also but don't know how to use it. I should look into it

yup it's compatible thanks. However I already started preclearing the drive again though a telnet session. Guess there is no way to transfer it over to screen.

does screen work with terminal from a Mac

So I was running a pre clear though telnet and I lost power last night. The server stayed up since I have a UPS on that but the computer that I logged into to telnet shut down. Guess I have to start over. I haven't lost power in at least 6 months so of course it has to happen now.

Influencer made a script for me to remove some of these files. PM him and see if you can get it. I'm at work or I would send it to you

Very happy with the way mine arrived. Pre clearing it 3 times to really test it out. Any idea how long that will take?

What does everyone use?