Jump to content

JorgeB

Moderators
 View Profile  See their activity

  • Posts

    67,735

  • Joined

  • Last visited

  • Days Won

    708

 Content Type 

Everything posted by JorgeB

  1. JorgeB
    Enable the syslog server and post that after a crash.
  2. JorgeB
    That's a good option.
  3. JorgeB
    Please use the existing plugin support thread:
  4. JorgeB
    Not unless the HBA is on a very old firmware, in that case you'll need to upgrade it.
  5. JorgeB
    Doesn't look like it is, only boot option listed is UEFI, you can also just enable UEFI boot on Unraid, by renaming EFI- to EFI in the flash drive. If you want to boot legacy the option is not "USB legacy support", look for CSM boot, legacy boot, or similar.
  6. JorgeB
    LSI is being correctly detected and initialized, so the problem lies elsewhere, although the probability is low I would first use an SFF-8088 to SATA cable to see if any disk is detected there, if yes, it rules out a problem with the HBA ports, leaving as the other possibilities the cables or enclosures.
  7. JorgeB
    Same.
  8. JorgeB
    Unfortunately there's nothing relevant logged before the crash, could be a hardware issue, one thing you can try it to boot the server in safe mode with all docker/VMs disable, let it run as a basic NAS for a few days, if it still crashes it's likely a hardware problem, if it doesn't start turning on the other services one by one.
  9. JorgeB
    You just need to re-assign it to rebuild on top, last part of: https://wiki.unraid.net/Manual/Storage_Management#Rebuilding_a_drive_onto_itself
  10. JorgeB
    If now it's failing immediately on mount it looks like a device problem.
  11. JorgeB
    It should all work fine except there won't be trim support for any SSDs assigned as array devices, so performance might degrade with time, thou it will also depend on the devices used.
  12. JorgeB
    Make sure you have the latest BIOS and check for that option, but I wound be surprised to see PCIe bifurcation on an X8, I believe support started with some X9 series, and even on those in latest BIOS only.
  13. JorgeB
    You need to look at the complete model, but as long as the speed is the same or higher than your CPU supports and it's the same type of RAM, in this case ECC UDIMM, they will work, slower would also work but it would downgrade performance.
  14. JorgeB
    It's fine.
  15. JorgeB
    Thanks, I will.
  16. JorgeB
  17. JorgeB
    Problem is the Marvell controller, this sometimes help, or better yet replace it with one of the recommended models.
  18. JorgeB
    Please post the diagnostics.
  19. JorgeB
    You should replace it then, or at least swap both cables/slot with another one to rule that out and then replace if more errors.
  20. JorgeB
    You'll need to force it then.
  21. JorgeB
    Type reboot or poweroff in the console depending on what you want to do.
  22. JorgeB
    No, it will only use one, just rebalance to the intended profile: https://forums.unraid.net/topic/46802-faq-for-unraid-v6/?do=findComment&comment=480421
  23. JorgeB
    Other than it being deleted (on purpose or not), not really.
  24. JorgeB
    It's worth trying. both things you mentioned.
  25. JorgeB
    There's no partition on that device, so it was deleted or something else happened, you can try testdisk or other recovery tool to see if you can get it back.
×
×
  • Create New...