flyize Posted May 2, 2022 Share Posted May 2, 2022 And now it looks like it just got pulled 1 Quote Link to comment
flyize Posted May 2, 2022 Share Posted May 2, 2022 Yay. Up and running on 5.18rc5 kernel. Gonna give it a day, just to make sure the kernel is stable. 2 1 Quote Link to comment
Brandon_K Posted May 2, 2022 Share Posted May 2, 2022 1 minute ago, flyize said: Yay. Up and running on 5.18rc5 kernel. Gonna give it a day, just to make sure the kernel is stable. Please please report back and let us know how it goes! 1 Quote Link to comment
SimonF Posted May 2, 2022 Share Posted May 2, 2022 41 minutes ago, flyize said: Yay. Up and running on 5.18rc5 kernel. Gonna give it a day, just to make sure the kernel is stable. I did a test load and notice there is no firmware for i915 so not sure will work without updated bzfirmware also. Also any plugins that are kernel specific will fail to load, i.e. nvidia, zfs, usbip etc. May 2 17:42:16 computenode kernel: Linux agpgart interface v0.103 May 2 17:42:16 computenode kernel: ACPI: bus type drm_connector registered May 2 17:42:16 computenode kernel: i915 0000:00:02.0: [drm] VT-d active for gfx access May 2 17:42:16 computenode kernel: checking generic (4000000000 1fa4000) vs hw (6001000000 1000000) May 2 17:42:16 computenode kernel: checking generic (4000000000 1fa4000) vs hw (4000000000 10000000) May 2 17:42:16 computenode kernel: fb0: switching to i915 from EFI VGA May 2 17:42:16 computenode kernel: Console: switching to colour dummy device 80x25 May 2 17:42:16 computenode kernel: i915 0000:00:02.0: vgaarb: deactivate vga console May 2 17:42:16 computenode kernel: i915 0000:00:02.0: [drm] Transparent Hugepage mode 'huge=within_size' May 2 17:42:16 computenode kernel: i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem May 2 17:42:16 computenode kernel: i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adls_dmc_ver2_01.bin (v2.1) May 2 17:42:16 computenode kernel: i915 0000:00:02.0: Direct firmware load for i915/tgl_guc_69.0.3.bin failed with error -2 May 2 17:42:16 computenode kernel: i915 0000:00:02.0: [drm] GuC firmware i915/tgl_guc_69.0.3.bin: fetch failed with error -2 May 2 17:42:16 computenode kernel: i915 0000:00:02.0: [drm] GuC firmware(s) can be downloaded from https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/i915 May 2 17:42:16 computenode kernel: i915 0000:00:02.0: [drm] GuC firmware i915/tgl_guc_69.0.3.bin version 0.0 May 2 17:42:16 computenode kernel: i915 0000:00:02.0: [drm] GuC is uninitialized May 2 17:42:16 computenode elogind-uaccess-command[16611]: Failed to reset ACL on /dev/dri/card0: Operation not supported May 2 17:42:16 computenode kernel: [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 May 2 17:42:16 computenode elogind-uaccess-command[16612]: Failed to reset ACL on /dev/dri/card0: Operation not supported May 2 17:42:16 computenode elogind-uaccess-command[16613]: Failed to reset ACL on /dev/dri/card0: Operation not supported May 2 17:42:16 computenode elogind-uaccess-command[16614]: Failed to reset ACL on /dev/dri/card0: Operation not supported May 2 17:42:16 computenode elogind-uaccess-command[16615]: Failed to reset ACL on /dev/dri/card0: Operation not supported May 2 17:42:16 computenode kernel: ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) May 2 17:42:16 computenode kernel: input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8 May 2 17:42:16 computenode elogind-uaccess-command[16616]: Failed to reset ACL on /dev/dri/card0: Operation not supported May 2 17:42:16 computenode elogind-uaccess-command[16617]: Failed to reset ACL on /dev/dri/card0: Operation not supported May 2 17:42:16 computenode elogind-uaccess-command[16619]: Failed to reset ACL on /dev/dri/card0: Operation not supported May 2 17:42:16 computenode kernel: fbcon: i915drmfb (fb0) is primary device May 2 17:42:16 computenode kernel: Console: switching to colour frame buffer device 480x135 May 2 17:42:16 computenode kernel: i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device May 2 17:42:16 computenode elogind-uaccess-command[16620]: Failed to reset ACL on /dev/dri/card0: Operation not supported Quote Link to comment
flyize Posted May 2, 2022 Share Posted May 2, 2022 Well crap. Is there any easy way for me to do that? I'm guessing not. Quote Link to comment
SimonF Posted May 2, 2022 Share Posted May 2, 2022 36 minutes ago, flyize said: Well crap. Is there any easy way for me to do that? I'm guessing not. Will review tomorrow may be able to download and then run modprobe i915 in go file from here https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/i915 2 Quote Link to comment
DeadDevil6210 Posted May 3, 2022 Share Posted May 3, 2022 12 hours ago, flyize said: Yay. Up and running on 5.18rc5 kernel. Gonna give it a day, just to make sure the kernel is stable. I'm not running anny of the plugins mentioned by SimonF and everything works great Took the gues on this custom kernel yesterday, It is still working grreat here (Plex Transcoding) server is up for more then 12 hours without one crash and multiple streams on plex done with and without transcoding: For those needing a bit of a direction with the parameter overwrite mentioned on the github page: Go to your flash drive --> syslinux configuration section and under Unraid OS (green bar) You will see: kernel /bzimage append isolcpus=15 initrd=/bzroot Modify to: kernel /bzimage append isolcpus=15 initrd=/bzroot md_mod.unraid_patch=22 (number according to post number --> unraid version translation) It seems to work great gonna experiment with Unmanic today 1 1 Quote Link to comment
SimonF Posted May 3, 2022 Share Posted May 3, 2022 2 hours ago, DeadDevil6210 said: I'm not running anny of the plugins mentioned by SimonF and everything works great Took the gues on this custom kernel yesterday, It is still working grreat here (Plex Transcoding) server is up for more then 12 hours without one crash and multiple streams on plex done with and without transcoding: For those needing a bit of a direction with the parameter overwrite mentioned on the github page: Go to your flash drive --> syslinux configuration section and under Unraid OS (green bar) You will see: kernel /bzimage append isolcpus=15 initrd=/bzroot Modify to: kernel /bzimage append isolcpus=15 initrd=/bzroot md_mod.unraid_patch=22 (number according to post number --> unraid version translation) It seems to work great gonna experiment with Unmanic today Did you need to load additional firmware? Quote Link to comment
flyize Posted May 3, 2022 Share Posted May 3, 2022 1 hour ago, SimonF said: Did you need to load additional firmware? I just turned on hardware transcoding and Plex shows that its using it. Seems odd based on whats in the system log. Weird. I guess we'll see how stable it is? Quote Link to comment
SimonF Posted May 3, 2022 Share Posted May 3, 2022 2 hours ago, flyize said: I just turned on hardware transcoding and Plex shows that its using it. Seems odd based on whats in the system log. Weird. I guess we'll see how stable it is? Used 5.18rc2 vers of firmware from github. computenode kernel: i915 0000:00:02.0: [drm] Transparent Hugepage mode 'huge=within_size' computenode kernel: i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem computenode kernel: i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adls_dmc_ver2_01.bin (v2.1) computenode kernel: i915 0000:00:02.0: [drm] GuC firmware i915/tgl_guc_69.0.3.bin version 69.0 computenode kernel: i915 0000:00:02.0: [drm] HuC firmware i915/tgl_huc_7.9.3.bin version 7.9 computenode kernel: i915 0000:00:02.0: [drm] HuC authenticated computenode kernel: i915 0000:00:02.0: [drm] GuC submission disabled computenode kernel: i915 0000:00:02.0: [drm] GuC SLPC disabled computenode kernel: [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 computenode elogind-uaccess-command[13899]: Failed to reset ACL on /dev/dri/card0: Operation not supported Looks better. 1 Quote Link to comment
DeadDevil6210 Posted May 3, 2022 Share Posted May 3, 2022 4 hours ago, SimonF said: Did you need to load additional firmware? No I did not need to load any firmware. I'm using 5.18rc5 kernel. Quote Link to comment
flyize Posted May 3, 2022 Share Posted May 3, 2022 1 hour ago, SimonF said: Used 5.18rc2 vers of firmware from github. computenode kernel: i915 0000:00:02.0: [drm] Transparent Hugepage mode 'huge=within_size' computenode kernel: i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem computenode kernel: i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adls_dmc_ver2_01.bin (v2.1) computenode kernel: i915 0000:00:02.0: [drm] GuC firmware i915/tgl_guc_69.0.3.bin version 69.0 computenode kernel: i915 0000:00:02.0: [drm] HuC firmware i915/tgl_huc_7.9.3.bin version 7.9 computenode kernel: i915 0000:00:02.0: [drm] HuC authenticated computenode kernel: i915 0000:00:02.0: [drm] GuC submission disabled computenode kernel: i915 0000:00:02.0: [drm] GuC SLPC disabled computenode kernel: [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 computenode elogind-uaccess-command[13899]: Failed to reset ACL on /dev/dri/card0: Operation not supported Looks better. Interesting. That doesn't have whatever 6.10RCx changes were done. Quote Link to comment
flyize Posted May 3, 2022 Share Posted May 3, 2022 7 hours ago, flyize said: I just turned on hardware transcoding and Plex shows that its using it. Seems odd based on whats in the system log. Weird. I guess we'll see how stable it is? Seems it doesn't work with hardware transcoding. Not sure why it was showing that it did. 1 Quote Link to comment
DontPlexOnMe Posted May 4, 2022 Share Posted May 4, 2022 Hey everyone, just following this thread and almost purchased a i5 12600k today to build a new plex/unraid/docker/vm server. Im assuming the igpu issue is still present, is it close to being fixed or should I still use my i7 8700? thanks! Quote Link to comment
Wintersdark Posted May 4, 2022 Share Posted May 4, 2022 56 minutes ago, DontPlexOnMe said: Hey everyone, just following this thread and almost purchased a i5 12600k today to build a new plex/unraid/docker/vm server. Im assuming the igpu issue is still present, is it close to being fixed or should I still use my i7 8700? thanks! I'd *strongly* recommend waiting. If you really want to upgrade now, maybe get an 11700 instead. Quote Link to comment
Cajones Posted May 4, 2022 Share Posted May 4, 2022 57 minutes ago, DontPlexOnMe said: Hey everyone, just following this thread and almost purchased a i5 12600k today to build a new plex/unraid/docker/vm server. Im assuming the igpu issue is still present, is it close to being fixed or should I still use my i7 8700? thanks! I don't think anyone can officially answer that question of when it would get fixed except limetech. My recommendation would be to hold what you have for a bit longer until support is improved. 1 Quote Link to comment
Brandon_K Posted May 4, 2022 Share Posted May 4, 2022 1 hour ago, DontPlexOnMe said: Hey everyone, just following this thread and almost purchased a i5 12600k today to build a new plex/unraid/docker/vm server. Im assuming the igpu issue is still present, is it close to being fixed or should I still use my i7 8700? thanks! The 12600k can do at least two 4K transcodes on CPU alone, which is going to be the same limit that your 8700 can do on QSV. While there isn't any iGPU support for Alder Lake support right now, you'll still have better overall performance with the 12600k, even with transcoding. Quote Link to comment
Wintersdark Posted May 4, 2022 Share Posted May 4, 2022 11 minutes ago, Brandon_K said: The 12600k can do at least two 4K transcodes on CPU alone, which is going to be the same limit that your 8700 can do on QSV. While there isn't any iGPU support for Alder Lake support right now, you'll still have better overall performance with the 12600k, even with transcoding. Eeeeeh I mean, 2 4k HEVC transcodes maybe. But if he's serving multiple people it's a very different story. My old G5400 Celeron could easily handle 12 concurrent 1080p transcodes and a 4k HEVC transcode. Meanwhile, my current 12400 struggles to manage 4 concurrent transcodes, and starts buffering if any cpu power is used anywhere else. It's a huge problem for me, because the brand new 12400 is wildly inferior in practice to the crappy old *dual core* 2.5ghz Celeron. 2 Quote Link to comment
DontPlexOnMe Posted May 4, 2022 Share Posted May 4, 2022 Eeeeeh I mean, 2 4k HEVC transcodes maybe. But if he's serving multiple people it's a very different story. My old G5400 Celeron could easily handle 12 concurrent 1080p transcodes and a 4k HEVC transcode. Meanwhile, my current 12400 struggles to manage 4 concurrent transcodes, and starts buffering if any cpu power is used anywhere else. It's a huge problem for me, because the brand new 12400 is wildly inferior in practice to the crappy old *dual core* 2.5ghz Celeron.Yeah, I’ll be having about 3-5 streams at once. So yeah that actually would be a problem right now. Does the 11th gen have the same issue?? Or is it only the 12th gen processors. I love the geek bench scores of the 12th gen but not having the igpu is probably gonna kill me and have a lot of pissed off family members lolSent from my iPhone using Tapatalk Quote Link to comment
flyize Posted May 4, 2022 Share Posted May 4, 2022 20 hours ago, SimonF said: Used 5.18rc2 vers of firmware from github. computenode kernel: i915 0000:00:02.0: [drm] Transparent Hugepage mode 'huge=within_size' computenode kernel: i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem computenode kernel: i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adls_dmc_ver2_01.bin (v2.1) computenode kernel: i915 0000:00:02.0: [drm] GuC firmware i915/tgl_guc_69.0.3.bin version 69.0 computenode kernel: i915 0000:00:02.0: [drm] HuC firmware i915/tgl_huc_7.9.3.bin version 7.9 computenode kernel: i915 0000:00:02.0: [drm] HuC authenticated computenode kernel: i915 0000:00:02.0: [drm] GuC submission disabled computenode kernel: i915 0000:00:02.0: [drm] GuC SLPC disabled computenode kernel: [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 computenode elogind-uaccess-command[13899]: Failed to reset ACL on /dev/dri/card0: Operation not supported Looks better. Were you able to test transcoding? Quote Link to comment
Wintersdark Posted May 4, 2022 Share Posted May 4, 2022 5 hours ago, DontPlexOnMe said: Yeah, I’ll be having about 3-5 streams at once. So yeah that actually would be a problem right now. Does the 11th gen have the same issue?? Or is it only the 12th gen processors. I love the geek bench scores of the 12th gen but not having the igpu is probably gonna kill me and have a lot of pissed off family members lol Sent from my iPhone using Tapatalk Only 12th gen. The 11700 is roughly comparable in power to the 12600 as well, so you're not getting a weaker system, and you'll end up with likely a cheaper motherboard too. I deeply regret doing the 12400 thing myself, but it's way too late unfortunately. Quote Link to comment
DontPlexOnMe Posted May 4, 2022 Share Posted May 4, 2022 Only 12th gen. The 11700 is roughly comparable in power to the 12600 as well, so you're not getting a weaker system, and you'll end up with likely a cheaper motherboard too. I deeply regret doing the 12400 thing myself, but it's way too late unfortunately. Hmm okay, Ill scour new egg and see if there’s a cheaper option but I wonder if I should just stay with my i7 8700. So many decisions [emoji28]Basically I’m only transcoding 1080p with about 5-8 users. Only reason why I was switching was to get away from rclone and google drive as it locks the server up now at 3-4 streams. Also sorry for hijacking this thread [emoji28]Sent from my iPhone using Tapatalk Quote Link to comment
SimonF Posted May 4, 2022 Share Posted May 4, 2022 6 hours ago, flyize said: Were you able to test transcoding? Not had time as yet. Likely to be the weekend. Quote Link to comment
flyize Posted May 4, 2022 Share Posted May 4, 2022 Just now, SimonF said: Not had time as yet. Likely to be the weekend. Well then I'll try tonight and let you know. Quote Link to comment
SimonF Posted May 4, 2022 Share Posted May 4, 2022 6 minutes ago, flyize said: @SimonF How did you get that RC2 version to work. I'm getting an error where the array won't start. It says 'incompatible md version'. Used 5.18rc5 for kernel and only used bzfirmware from 5.18RC2. Unraid vers was 6.10rc5 https://github.com/thor2002ro/unraid_kernel/releases/download/20220412-5.18rc2/bzfirmware.7z Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.