Thanks Pinion for the ideas - not sure what you mean by running it with the stock go file - ill look into it a little later. however if you believe I shouldn't run plugins at the moment then that is not great, however I will look int this

 

Thanks

...Parity - This is always orange is this correct ?...

Parity is not always orange. Since you have been having unclean shutdowns it is probably still trying to complete a parity sync.

 

Your syslog seems to indicate you are running out of memory.

 

If you want a stable system I suggest you revert to stock and let your parity sync complete.

 

Hi thanks for the feedback

 

I have heard this twice now what does stock mean - no pluggins ? I think you are correct I have looked at my system setting for transmission and seems to be down loading to //downloads ? would this be the ram drive that may be filling up and causing it to die?

 

I can tell you however that my parity sync has finished and it is all fine however cache and all the shares on it are still showing up as orange- what can I do here ?

 

Thanks

 

Rod

I just saw your link ill do that now

 

thanks

 

Rodroll

Orange on cache and cached shares just means there are files that have not been moved off cache yet. Cache-only shares will always be orange.

 

Hello

 

I try and run the go file and the following error appears

 

-bash: ./go: /bin/bash^M: bad interpreter: No such file or directory

 

am I missing some thing ?

Hello

 

I try and run the go file and the following error appears

 

-bash: ./go: /bin/bash^M: bad interpreter: No such file or directory

 

am I missing some thing ?

Did you revert to stock? Is your go file exactly:

#!/bin/bash
# Start the Management Utility
/usr/local/sbin/emhttp &

 

You don't run the go file. After following the instructions to revert to stock you should do a clean shutdown and reboot.

 

Hi I have done this, however now on reboot it comes up with a whole lot of issues saying it can find find files that it is looking for under config, it also fails to load smbd on nmbd so my servers is not up and running at all with out direct terminal access, what should I do from here.

I have checked to make sure the go file was correct

 

 

If your go file is stock and you're not running any plugins but still having problems you should post your latest problems with your system log to the general support section. You might get a broader range of people who can answer you there.

Hi I have done this, however now on reboot it comes up with a whole lot of issues saying it can find find files that it is looking for under config, it also fails to load smbd on nmbd so my servers is not up and running at all with out direct terminal access, what should I do from here.

I have checked to make sure the go file was correct

Yes, take this to General Support. If no plugins are running then this is not a plugin issue.

 

See here for help on getting and posting your system log to the other forum.

I understand your point. However I now have a system that is not running at all. I can't telnet to it or see it unless I use the ip address. I seemed to have gone from a machine that was running some of the time to one that is lot running at all. I am not sure how I can post a Sys.log fine now if it is failing to even load correctly.

 

I really need help to get it back to where it was so I can at least have that as a starting point.

I have tried renaming the extras folder to what it was and it is still failing to load.

PLEASE HELP!!

Hi the link is not working ? Can you please repost it.

http://lime-technology.com/wiki/index.php/Troubleshooting

Hi. User EMKO noticed that Simplefeatures and Sabnzbd install two different versions of openssl: http://lime-technology.com/forum/index.php?topic=12698.msg231583#msg231583

 

We both experience SF gui instability while using sabnzbd. After removing openssl 0.9.8 from the sabnzbd.plg and package folder and restarting the server, SF gui seems to remain responsive. I have tested this now for 10h, it's still responsive.

Hi,

 

I am wondering whenever I tried to stop and start sickbeard. I am getting this

 

29304 ?        S      0:00 /usr/bin/tail -n 40 -f /var/log/syslog enable nobody 8083 /usr/local/sickbeard /mnt/cache/.plugins/sickbeard yes yes https://github.com/midgetspy/Sick-Beard master

29313 ?        S      0:00 /bin/sh /etc/rc.d/rc.sickbeard updateplg enable nobody 8083 /usr/local/sickbeard /mnt/cache/.plugins/sickbeard yes yes https://github.com/midgetspy/Sick-Beard master

 

Also I am seeing it in the syslog not like sabnzbd and couchpotato.

 

If you will notice in my syslog there are no couchpotato nor sabnzbd logging.

 

/usr/bin/tail -n 40 -f /var/log/syslog enable nobody 8083 /usr/local/sickbeard /mnt/cache/.plugins/sickbeard yes yes https://github.com/midgetspy/Sick-Beard master

==> /var/log/syslog <==

Mar 18 21:33:00 unRaid cache_dirs: max_seconds=10, min_seconds=1

Mar 18 21:33:00 unRaid cache_dirs: max_depth=9999

Mar 18 21:33:00 unRaid cache_dirs: command=find -noleaf

Mar 18 21:33:00 unRaid cache_dirs: version=1.6.6

Mar 18 21:33:00 unRaid cache_dirs: ---------- caching directories ---------------

Mar 18 21:33:00 unRaid cache_dirs: .plugins

Mar 18 21:33:00 unRaid cache_dirs: Media

Mar 18 21:33:00 unRaid cache_dirs: backup

Mar 18 21:33:00 unRaid cache_dirs: ----------------------------------------------

Mar 18 21:33:00 unRaid cache_dirs: cache_dirs process ID 25495 started, To terminate it, type: cache_dirs -q

Mar 18 21:33:55 unRaid sSMTP[25709]: Creating SSL connection to host

Mar 18 21:33:56 unRaid sSMTP[25709]: SSL connection using RC4-SHA

==> /usr/local/sickbeard <==

 

==> /mnt/cache/.plugins/sickbeard <==

 

==> /var/log/syslog <==

 

 

I am using rc11 and sf 1.0.5

I tried to install the latest sickbeard today, but it won't start.

I get this error when enabling/installing it in unraids webgui:

 

Warning: parse_ini_file(/boot/config/plugins/sickbeard/sickbeard.cfg): failed to open stream: No such file or directory in /usr/local/emhttp/plugins/sickbeard/sickbeard.php on line 2

 

What can be wrong here? I have both SABNZB and NZBGet installed on 5.0RC11. Both were running fine but NZBGet stopped too when I tried to install Sickbeard.

 

 

It could also be a problem running the transmission plugin, my server was getting kernel panics when transmission was running for a few hours, I ended up setting up a VM for my torrents, running rtorrent in ubuntu,.

 

Sent from my Nexus 7 using Tapatalk HD

Hi Influencer,

 

Thanks a lot for the SABSuite plugins and your dedication with supporting them!

I have the following situation:

 

SAB is up and running properly. SickBeard works like a charm together with SAB already. (Haven't tried Headphones and mylar yet).

 

After configuring CPv2 I have the problem that I cannot add any wanted movies. When I type a movie name in, it will look for the movie and ask for the desired resolution. When I tell CP to add the movie the spinner will spin forever and I get the following error in the log (tried to add "Alien"):

 

http://pastebin.com/LP4yQLue

 

Thanks for caring,

JC

Latest stable transmission-2.77-i686-1PTr.txz (please map to plugin, THX)

 

https://truck.it/p/v5ap5OtXhT

I have an interesting issue that i've only just noticed with sick beard. Hope it's easy to fix?!

 

I use torrents and so the black hole method where it downloads to a certain folder and sickbeard picks it up and processes it. Now becuase it's torrents i have ticked "keep original files", (so i can seed) and also "scan and process", (so that it can do it's thing). (this is where i think the issue is arising and i need another way of doing it).

 

Every 10 minutes SB scans the folder, sees there is stuff in there and then processes it over and over and over. Ordinarily i presume that this is the norm, so because it checks the destination folder and sees that it's already processed it, it leaves it alone. But it's not, it's processing it and overwriting the files that has already been processed.

 

This then has a knock on affect of engaging pled media server to rescan for new content once finished (as it's designed to do). it also keeps my drives alive and does a lot of writing to the array which i don;t like.

 

in SB log it states:

 

Mar-24 19:41:08 DEBUG    POSTPROCESSER :: Deleting file

Mar-24 19:41:08 DEBUG    POSTPROCESSER :: This download is marked a priority download so I'm going to replace an existing file if I find one

Mar-24 19:41:08 DEBUG    POSTPROCESSER :: Is ep a priority download: True

Mar-24 19:41:08 DEBUG    POSTPROCESSER :: SB snatched this episode so I'm marking it as priority

 

 

 

How do i stop this/how do other people have this set up as i need to change something??

 

cheers

 

EDIT* It looks like the problem is that its not really designed to post process and keep the files. So i think that as i have the capacity it should, once the download completes copy the file to another folder that sickbeard can scan, process and then delete. Does anybody have something that can facilitate in copying the file, so that once complete it automatically triggers a file copy?

Below is a simple shell script I created to copy files into the SB processing directory. First, it checks to see if the file is actually in the download directory. Second, because I do not want every torrent copied into the SB processing directory, it only copies files that have been downloaded into my dedicated seed directory.

 

#!/bin/sh
if [ -e "$TR_TORRENT_DIR/$TR_TORRENT_NAME" ] && [ "$TR_TORRENT_DIR" == "/mnt/user/Seed" ]; then
cp -R "$TR_TORRENT_DIR/$TR_TORRENT_NAME" "/mnt/user/Seed/1Process" 2>/dev/null
fi

 

you also have to modify the settings.json file to

 

    "script-torrent-done-enabled": true, 
    "script-torrent-done-filename": "/mnt/user/appdata/transmission/post.sh", 

 

I installed both the Sabnzbd plugin, but it fails to shut down when I try to stop the array. Invoking

/etc/rc.d/rc.sabnzbd stop

does nothing and produces no output. I have traced the problem to the way the script detects the right port to use, and specifically, then using https, the stop function will be trying to look for a pid file named from the non-https port.

 

The following section in rc.sabnzbd needs to change:

# read our configuration
source /boot/config/plugins/sabnzbd/sabnzbd.cfg
if [ -e $DATADIR/sabnzbd.ini ]; then
PORT=`cat "$DATADIR/sabnzbd.ini" | grep '^port' | awk 'NR==1' | cut -d' ' -f3 | tr -d '\r'`
else
PORT=`cat /boot/config/plugins/sabnzbd/sabnzbd.ini | grep '^port' | awk 'NR==1' | cut -d' ' -f3 | tr -d '\r'`
fi 

 

Change To:

# read our configuration
source /boot/config/plugins/sabnzbd/sabnzbd.cfg
if [ -e $DATADIR/sabnzbd.ini ]; then
	HTTPS=`cat "$DATADIR/sabnzbd.ini" | grep 'enable_https' | cut -d' ' -f3`
		if [ $HTTPS = 0 ]; then
			PORT=`cat "$DATADIR/sabnzbd.ini" | grep '^port' | awk 'NR==1' | cut -d' ' -f3 | tr -d '\r'`
		elif [ $HTTPS = 1 ]; then
			PORT=`cat "$DATADIR/sabnzbd.ini" | grep 'https_port' | cut -d' ' -f3`
		fi
else
	HTTPS=`cat /boot/config/plugins/sabnzbd/sabnzbd.ini | grep 'enable_https' | cut -d' ' -f3`
		if [ $HTTPS = 0 ]; then
			PORT=`cat /boot/config/plugins/sabnzbd/sabnzbd.ini | grep '^port' | awk 'NR==1' | cut -d' ' -f3 | tr -d '\r'`
		elif [ $HTTPS = 1 ]; then
			PORT=`cat /boot/config/plugins/sabnzbd/sabnzbd.ini | grep 'https_port' | cut -d' ' -f3`
		fi
fi

 

I copied the https-port detection scheme from the plugin file itself and adapted to the rc script. Here's to hoping the author will implement these changes in the plugin file!

 

Actually, strike that. Not a god idea. Will have to be fixed some other way - probably best to disable the detection of https altogether or stop naming the pid file with the port suffix.

If someone are interested here im release most important packages for plugins special compiled for unraid in latest version

https://truck.it/p/Vq3zpArAKB (package python 2.7.3 contains yenc, pyopenssl, cheetah)

Im add some important patches from git (if found, like for cheetah etc.) and removed unnecessary files like doc or man etc. this only take space of ram.

Anyone have any issues with sickbeard coming back up after the latest upgrade today?