Jump to content

JorgeB

Moderators
 View Profile  See their activity

  • Posts

    63,929

  • Joined

  • Last visited

  • Days Won

    675

 Content Type 

Everything posted by JorgeB

  1. JorgeB
    If it's using btrfs the free space can sometimes be incorrectly reported and/or be fully allocated resulting in ENOSPC.
  2. JorgeB
    The only time I've seen VMs pause is when running out of space, not the vdisk itself, but the device where the vdisk is stored, in doubt post your diags.
  3. JorgeB
    No, I understood the array was not starting, so maybe there was filesystem corruption, but the array is started on the diags.
  4. JorgeB
    Please post your diagnostics, if you can't get them form the GUI type diagnostics on the console.
  5. JorgeB
    and stop the docker service before moving.
  6. JorgeB
    On the console type: mover stop
  7. JorgeB
    No, docker needs to be disable until all files are on cache again, if you have many small files it would be much faster moving them manually, e.g., with midnight commander (mc on the console), move from /mnt/cache to /mnt/disk#
  8. JorgeB
    Tom mentioned something about not being much around the forums this week, back to normal next week.
  9. JorgeB
    Once the data is on the array, stop it, and assuming it's a single cache device, click on it and change the cache filesystem to xfs, start the array and you'll have the option to format, you can then leave it as xfs if you don't have plans to create a cache pool or change back to btrfs and format again.
  10. JorgeB
    Backup your cache, reformat and restore the data, you can use this procedure to backup/restore.
  11. JorgeB
    No, I'm still using the same method. I don't use encryption but don't see a reason why it would cause issues.
  12. JorgeB
    Keep in mind that using the default raid1 model only 250GB will be usable, despite the main page showing free space available on the pool.
  13. JorgeB
    You can try, but the result will probably be the same, you can also run a filesystem check in case there's corruption.
  14. JorgeB
    Check it's using the latest firmware P20.00.07, there were two previous releases and the 1st one especially (p20.00.00) had issues.
  15. JorgeB
    Yes, and LT already confirmed that only the trial license (and a few betas releases in the past) communicate with their servers.
  16. JorgeB
    That one was already answered, yes it can.
  17. JorgeB
    You have something using that folder, reboot stop all docker/VMs and try again
  18. JorgeB
    Try again after stopping any plex related dockers
  19. JorgeB
    There's a problem somewhere, with turbo write enable I clear disks at 100MB/s+, post your diagnostics, maybe something visible.
  20. JorgeB
    You can use midnight commander (mc on the console), it will show a progress bar with ETA.
  21. JorgeB
    I have 10 unRAID licenses, some of which are more than 10 years old, never had a flash fail (though full disclosure had 2 replaced a long time ago because I used some lesser brand flash drives and they kept getting corrupted after each power cycle), just get good quality flash drives and don't worry.
  22. JorgeB
    That's likely a UEFI bug on the board you're using, bios update might help.
  23. JorgeB
    When CSM is disable only UEFI boot is available, so all HBA BIOS, NIC Boot ROMS, etc are skipped.
  24. JorgeB
    I don't remember what's the latest bios version, latest firmware is 20.00.07, the bios included with that will be the latest, and if you're running an older firmware it will likely also have an older bios.
  25. JorgeB
    Either boot DOS and use sas2flsh.exe or UEFI and use sas2flash.efi, both are on the wiki toolset: https://lime-technology.com/wiki/Crossflashing_Controllers#LSI_MegaRAID_with_SAS2008_chipsets Scroll down to the Notes and download LSI MegaRAID to SAS2008(P20).zip - 4.1 MB (FREEDOS, via bootable usb key), it contains both
×
×
  • Create New...