Jump to content

JorgeB

Moderators
 View Profile  See their activity

  • Posts

    67,067

  • Joined

  • Last visited

  • Days Won

    703

Community Answers

  1. JorgeB
    JorgeB's post in Out Of Memory errors detected on your server was marked as the answer   
    If it's a one time thing you can ignore, if it keeps happening try limiting more the RAM for VMs and/or docker containers, the problem is usually not just about not enough RAM but more about fragmented RAM, alternatively a small swap file on disk might help, you can use the swapfile plugin:
     
    https://forums.unraid.net/topic/109342-plugin-swapfile-for-691/
  2. JorgeB
    JorgeB's post in eth0 device does not exist was marked as the answer   
    That NIC is not working, so best bet is to get a new NIC (or use a different board/computer if available).
     
     
  3. JorgeB
    JorgeB's post in System frequently gets up to 100% CPU usage was marked as the answer   
    PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7542 nobody 20 0 394132 305528 12292 R 100.0 1.9 0:23.11 Plex Tran+  
    Plex?
  4. JorgeB
    JorgeB's post in 6.11.5 Another Daily Crasher was marked as the answer   
    Start here:
    https://forums.unraid.net/topic/46802-faq-for-unraid-v6/?do=findComment&comment=819173
     
  5. JorgeB
    JorgeB's post in Shuffling disks (moving from disk1 to parity) was marked as the answer   
    You need to do a new config (Tools -> New config)
  6. JorgeB
    JorgeB's post in Cannot select new XFS cache pool was marked as the answer   
    With the array stopped click on that pool and change "Enable user share assignment" from "no" to "yes".
     
  7. JorgeB
    JorgeB's post in Cache drives saying they're wrong and being emulated. was marked as the answer   
    Stop array, unassign all pool devices, start array, stop array, re-assign all pool devices, start array.
  8. JorgeB
    JorgeB's post in Everything missing after reboot and bios update was marked as the answer   
    Emulated disk is mounting, assuming contents look correct you can rebuild on top and re-sync parity at the same time:
     
    https://wiki.unraid.net/Manual/Storage_Management#Rebuilding_a_drive_onto_itself
     
     
  9. JorgeB
    JorgeB's post in System log prior to reboot? was marked as the answer   
    You can enable the syslog server.
  10. JorgeB
    JorgeB's post in Fix page fault errors? was marked as the answer   
    Looks like this issue:
     
     
  11. JorgeB
    JorgeB's post in All Disks Show Unmountable: Wrong or no file system after increasing array size and adding new disk was marked as the answer   
    A reboot should fix it.
  12. JorgeB
    JorgeB's post in Unable to restart the array after power failure was marked as the answer   
    USB is not recommended for array or pool devices.
  13. JorgeB
    JorgeB's post in Parity sync errors was marked as the answer   
    Mar 3 05:45:59 Bifrost emhttpd: unclean shutdown detected A few sync errors are normal, even expected, after this, just run a correcting check.
  14. JorgeB
    JorgeB's post in Cache drive - Unmountable: Wrong or no file system was marked as the answer   
    If the log is the only issue this might help:
     
    btrfs rescue zero-log /dev/nvme0n1p1  
    If it works make sure backups are up date since there a chance it can re-occur.
  15. JorgeB
    JorgeB's post in Two disabled disks, and cache drives not correct was marked as the answer   
    Replace cables for
     
    cache device: (sds) ADATA_SU655_2L1929199ERW  
    Or connect it to an onboard SATA port if available.
     
    Emulated disk is mounting assuming contents look correct you can rebuild on top (and re-sync parity2 at the same time).
  16. JorgeB
    JorgeB's post in Error when changing array HD was marked as the answer   
    They should be all valid, assuming parity was in sync.
  17. JorgeB
    JorgeB's post in Drives not showing in UNRAID - HP DL380 GEN9, HP B6200 Backup Storage & PERC H200e was marked as the answer   
    Logical block size: 520 bytes This is not supported, you'll need to re-format them with 512B sector size.
  18. JorgeB
    JorgeB's post in [Help] Array Health Report Fail was marked as the answer   
    Set both appropriately for SSDs, defaults are good gor HDDs only, I believe the array status only fails if critical temp is hit.
  19. JorgeB
    JorgeB's post in Downloadspeed slow, uploadspeed good was marked as the answer   
    Look for the tips and tweaks plugin, there are some NIC settings there that can make a difference.
  20. JorgeB
    JorgeB's post in [Solved] Server keeps crashing 6.11.5 was marked as the answer   
    Start here:
    https://forums.unraid.net/topic/46802-faq-for-unraid-v6/?do=findComment&comment=819173
     
  21. JorgeB
    JorgeB's post in Spreading data across all disks increasing performance was marked as the answer   
    ZFS doesn't distribute files, it stripes based on blocks for the drives in the pool, if you want that best to wait for v6.12 and use a zfs pool instead of the array.
  22. JorgeB
    JorgeB's post in Cache pool help - drive replacement was marked as the answer   
    Everything on cache is using raid1, including all folders you've moved back.
     
  23. JorgeB
    JorgeB's post in [6.10.3] Bad spare value from cache disks with Unraid was marked as the answer   
    Samsung is usually good, there have been some issues but from what I remember they are solved with a firmware update.
  24. JorgeB
    JorgeB's post in SSH connections to my server are refused was marked as the answer   
    Delete/rename /boot/config/ssh and reboot, note that any saved keys will be lost.
  25. JorgeB
    JorgeB's post in anxiety attack time. umm... help? was marked as the answer   
    No ATA errors on disk6 for now, check filesystem. 
×
×
  • Create New...