dtctechs

Members
  • Posts

    31
  • Joined

  • Last visited

Everything posted by dtctechs

  1. I have a very similar setup. Nextcloud and Vaultwarden behind Cloudflare proxy using NPM. I believe the only difference is that you are using custom proxy where I am using bridge for both containers. Are both containers on custom proxy? Is either container working via NPM? What are the IP:Port# of each? So if you go to Nextcloud or Vaultwarden and go to WEB UI it opens the exact same page with the exact same address in the address bar?
  2. Greetings, Earlier today my array crashed while I was downloading files via a docker container. I have attached diagnostics and Splunk logs. Infraction happened at 4:25:56:00 PM. Any direction is appreciated. unraid-diagnostics-20201208-1649.zip _splunk-logs.zip
  3. Great docker. I've been using it extensively since it originally became available on CA. Is there currently any way to get the dockerized version to 16?
  4. Tested and confirmed. Living in the lower Southeast US the next-gen Bahamas & Mexico port forwarding is light years faster than Berlin! Thanks a lot dude. Your work is always appreciated.
  5. PIA Finally posted some info on NextGen port-forwarding. There's 3 official bash scripts here that are available to be pulled via Github. I thought folks in this thread would be interested. Please forgive me if this has already been mentioned. https://www.privateinternetaccess.com/helpdesk/kb/articles/next-generation-port-forwarding
  6. I'm having a problem with the built in proxy. I've had it running through binhex-qbittorrent privoxy ip:port for the longest time. The same proxy settings are working in binhex-radarr, also tested successfully on a windows box. When the proxy is enabled I can't 'Add Series', when I turn proxy off 'Add Series' works as normal. Would anything have changed to cause this issue or is it somewhere on my end?
  7. I believe this has been mentioned in this thread, however, search terms are hard 😕 In the normal docker list dockers start in that order, from top to bottom, implementing 'wait' if enabled. What is the proper order that dockers start in when using folders? Am I correct in thinking the order is as follows: Folder 1 Docker 1 {Starts 1st} [Wait: 60] Docker 1.1 {Starts 2nd after 60 seconds} Docker 1.2 {Starts 3rd} Folder 2 Docker 2 {Starts 4th} Docker 2.1 {Starts 5th} Docker 2.2 {Starts 6th} Again, thanks for the a great plugin and your prompt replies to all of these requests!
  8. I doubt this is the preferred solution but have you tried to create a new profile for yourself and see how the metadata shows up? If it is proper then just use the new profile. It sounds like there is something corrupt in your individual profile. Also, you could always spin up a new Plex docker, linuxserver or other, along side the current one (if linuxserver use a different docker name and port) and see if you experience the same issues. I realize if you have a huge library this is not ideal, just a thought.
  9. That's good enough for me. I appreciate your suggestion!
  10. I am using the Docker Preview: No Icon option. I am also using Theme Engine. It seems in all themes the docker list text color is the same, a light gray color. It makes the docker lists very hard to read in most themes. Image below. Is there anyway to change this text color?
  11. I am using uGet. I am unable to sort columns. I've tried in WebVNC and direct VNC. For example when I click 'Complete' column, the session flashes and organizes for 1-2 seconds then reverts right back to the previous sorting. I am not sure if this is some sort of restriction or a problem on my end. Any help is appreciated.
  12. Greetings - This looks awesome, however upon installation I receive the following: root@localhost:# /usr/local/emhttp/plugins/dynamix.docker.manager/scripts/docker run -d --name='trilium' --net='bridge' -e TZ="America/New_York" -e HOST_OS="Unraid" -p '8888:8080/tcp' -v '/mnt/user/appdata/trilium':'/root/trilium-data':'rw' -v '{2}':'/root/trilium-data/backup':'rw' 'zadam/trilium:0.43.2' /usr/bin/docker: Error response from daemon: create {2}: "{2}" includes invalid characters for a local volume name, only "[a-zA-Z0-9][a-zA-Z0-9_.-]" are allowed. If you intended to pass a host directory, use absolute path. See '/usr/bin/docker run --help'. The command failed.
  13. I am looking to buy one of these for my T620 (eBay Link). The full Dell T620 documentation shows details on the 12x backplane, how to install it, etc. As far as I can tell it only has 2 SAS connectors, SAS A & SAS B. I am lead to believe that this backplane must have SAS Expander built in? I see that it has a heatsink on the board. I currently have a LSI 9211-8i powering the current 8 drives, is this enough to connect all 12 drives on this 12 drive backplane or will it require a more robust card?
  14. Disregard, I figured it out 5 seconds after posting. Thanks for the great plugin!
  15. I have built a couple Arch Linux VMs using xf86-qxl-video drivers. The drivers seem to work proper, I have all the resolutions in my display settings, lspci shows Red Hat Qxl drivers, etc. However using a GUI via VNC is extremely slow graphic wise. I have an AMD 3900x, VM has 4 threads, 8gb RAM. System resources look fine but switching between windows (redraw) is painfully slow regardless of wallpaper, window manager settings, etc. However if I go to Virt-Manager docker and change the Video from QXL to Virtio the GUI works flawlessly even with compositing. Has anyone else experienced this? Is there something in my VM settings that need to be tweaked to support QXL? Example XML below. <?xml version='1.0' encoding='UTF-8'?> <domain type='kvm'> <name>Arch-Mate</name> <uuid>6819f532-76c6-6a28-4886-0d3a0dcabd78</uuid> <metadata> <vmtemplate xmlns="unraid" name="Arch" icon="arch.png" os="arch"/> </metadata> <memory unit='KiB'>8388608</memory> <currentMemory unit='KiB'>8388608</currentMemory> <memoryBacking> <nosharepages/> </memoryBacking> <vcpu placement='static'>4</vcpu> <cputune> <vcpupin vcpu='0' cpuset='8'/> <vcpupin vcpu='1' cpuset='9'/> <vcpupin vcpu='2' cpuset='10'/> <vcpupin vcpu='3' cpuset='11'/> </cputune> <os> <type arch='x86_64' machine='pc-q35-4.2'>hvm</type> </os> <features> <acpi/> <apic/> </features> <cpu mode='host-passthrough' check='none'> <topology sockets='1' cores='2' threads='2'/> <cache mode='passthrough'/> <feature policy='require' name='topoext'/> </cpu> <clock offset='utc'> <timer name='rtc' tickpolicy='catchup'/> <timer name='pit' tickpolicy='delay'/> <timer name='hpet' present='no'/> </clock> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/local/sbin/qemu</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='writeback'/> <source file='/mnt/disks/SanDisk_X400_M.2_2280_512GB_163377423207/VM/Mate/vdisk1.img'/> <target dev='hdc' bus='virtio'/> <boot order='1'/> <address type='pci' domain='0x0000' bus='0x04' slot='0x00' function='0x0'/> </disk> <controller type='usb' index='0' model='ich9-ehci1'> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x7'/> </controller> <controller type='usb' index='0' model='ich9-uhci1'> <master startport='0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0' multifunction='on'/> </controller> <controller type='usb' index='0' model='ich9-uhci2'> <master startport='2'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x1' multifunction='on'/> </controller> <controller type='usb' index='0' model='ich9-uhci3'> <master startport='4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x2'/> </controller> <controller type='pci' index='3' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='3' port='0x12'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x2'/> </controller> <controller type='pci' index='4' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='4' port='0x13'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x3'/> </controller> <controller type='pci' index='5' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='5' port='0x14'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x4'/> </controller> <controller type='pci' index='6' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='6' port='0x15'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x5'/> </controller> <controller type='virtio-serial' index='0'> <address type='pci' domain='0x0000' bus='0x03' slot='0x00' function='0x0'/> </controller> <controller type='sata' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x1f' function='0x2'/> </controller> <controller type='pci' index='0' model='pcie-root'/> <controller type='pci' index='1' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='1' port='0x10'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0' multifunction='on'/> </controller> <controller type='pci' index='2' model='pcie-root-port'> <model name='pcie-root-port'/> <target chassis='2' port='0x11'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x1'/> </controller> <filesystem type='mount' accessmode='passthrough'> <source dir='/mnt/user/'/> <target dir='unraid'/> <address type='pci' domain='0x0000' bus='0x01' slot='0x00' function='0x0'/> </filesystem> <interface type='bridge'> <mac address='52:54:00:fc:e3:b8'/> <source bridge='br0'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x02' slot='0x00' function='0x0'/> </interface> <serial type='pty'> <target type='isa-serial' port='0'> <model name='isa-serial'/> </target> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <channel type='unix'> <target type='virtio' name='org.qemu.guest_agent.0'/> <address type='virtio-serial' controller='0' bus='0' port='1'/> </channel> <input type='tablet' bus='usb'> <address type='usb' bus='0' port='1'/> </input> <input type='mouse' bus='ps2'/> <input type='keyboard' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' websocket='-1' listen='0.0.0.0' keymap='en-us'> <listen type='address' address='0.0.0.0'/> </graphics> <video> <model type='qxl' ram='65536' vram='65536' vgamem='16384' heads='1' primary='yes'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x0'/> </video> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x05' slot='0x00' function='0x0'/> </memballoon> </devices> </domain>
  16. Reddit: how do I backup using rsync? spaceinvader1 guide to moving files Both of these helped me. You can use rsync from the command line once you have installed the plugin. It's as simple as rclone copy /mnt/user/share-to-backup /mnt/disks/unassigned-device-path Here is a list of flags you can use https://rclone.org/flags/ Speed-wise I have had better luck using midnight commander from ssh terminal to copy from/to USB 3.0 drives.
  17. I did but apparently I fat-fingered the address. Everything is working properly, thank you.
  18. I assume my problem is that when I use Filebot I move the renamed files which then deletes the folder... so when I click Load the previous folder isn't there any more and it lands me in the default folder. I just created a new path called AAAADownloads so it stays at the top of the container root. This is good enough. Thanks for your reply.
  19. If it's just a one time backup use the Unassigned Devices plugin. It will mount your USB drive. From there you can use Midnight Commander (mc) from SSH/CLI or you can use something like Krusader or Cloud Commander dockers. These options lets you move the files back and fourth similar to explorer. If you are wanting to backup to external on a schedule you can use rsync plugin with User Scripts plugin. Search the forums for external backup scripts and you will find plenty of examples.
  20. Question: Is there anyway to set the 'home' folder that you land on when you open the docker and/or delete/move a folder? Every time I rename/move a folder it diverts back to the /config folder and I have to browse back to my /storage folder and drill down. Not a huge deal but I am curios if there is a way to set this in docker config.
  21. I finally got the app to update and remove 'not available' tag. I've tried several different ports including 6595/WebUI with no luck. Whenever I attempt to hit the UI it times out. Regardless of UI port I get this in my log.