warpspeed Posted March 15, 2016 Share Posted March 15, 2016 I upgraded from 5.0.5 straight to 6.1.9 on Sunday. I did it by shutting my server down, backing up the config off the stick, formatting and putting a fresh 6.1.9 on, then copying back my key and config files. It's worked fine so far. With one exception, needing to add sec=sys to my NFS RW exports. Quote Link to comment
skylark Posted March 20, 2016 Share Posted March 20, 2016 Just upgraded from v5.0.5 to 6.1.9 via 'method 1' and it went like a dream, nothing untoward as yet Now i've got to work out how to get my five disks (3x6TB, 2x4TB) converted from reiserfs to xfs. Fortunately i've got one spare slot with an 8TB drive now pre-clearing (thanks gfjardim!) nicely! Quote Link to comment
shootking Posted June 29, 2016 Share Posted June 29, 2016 Hello Today I tried to upgrade from 5.0 final to latest 6.x (downloaded plg plugin fråm http://lime-technology.com/forum/index.php?topic=41061.0) by method #2. Did two reboots of my Unraid and then it gives me an error message: Error: No configuuration file found No DEFAULT or UI configuration directive found! Where should I begin looking? Havent done much troubleshooting on Unraid... Regards Jens Quote Link to comment
Squid Posted June 29, 2016 Share Posted June 29, 2016 Hello Today I tried to upgrade from 5.0 final to 6.0.3 by method #2. Did two reboots of my Unraid and then it gives me an error message: Error: No configuuration file found No DEFAULT or UI configuration directive found! Where should I begin looking? Havent done much troubleshooting on Unraid... Regards Jens Might have to run makebootable on the flash drive. Where did you get 6.0.3? The Latest version is 6.1.9 Quote Link to comment
shootking Posted June 29, 2016 Share Posted June 29, 2016 Hello! OK, will look into the USB then. Sorry for the typo, I wasnt completely aware of the version number of the Unraid. Downloaded the PLG as described above in my modified post. Regards Jens Quote Link to comment
Frank1940 Posted June 29, 2016 Share Posted June 29, 2016 Hello! OK, will look into the USB then. Sorry for the typo, I wasnt completely aware of the version number of the Unraid. Downloaded the PLG as described above in my modified post. Regards Jens Describe what is happening as you go through the boot process. Are you seeing the boot choices screen and the notice that you are unpacking(?) bzimage and bzroot? If it is getting that far, you might want to run chkdsk on your flash drive. Quote Link to comment
shootking Posted June 29, 2016 Share Posted June 29, 2016 Hello I tried the make_bootable_mac on my MacBook. But got some error messages: cp: /Volumes/UNRAID/syslinux/*: No such file or directory To continue please enter your admin Password: sudo: /tmp/UNRAID/syslinux/make_bootable_mac.sh: command not found Leaving me with even more questions... Why isnt it working? Regards Jens Quote Link to comment
shootking Posted June 29, 2016 Share Posted June 29, 2016 Describe what is happening as you go through the boot process. Are you seeing the boot choices screen and the notice that you are unpacking(?) bzimage and bzroot? If it is getting that far, you might want to run chkdsk on your flash drive. 1. Computer boots showing bios alternatives (F2 & F10) 2. Computer shows the following message SYSLINUX 4.03 2010-10-22 EED Copyright © 1994-2010 H. Peter Anvin et al Error: No configuration file found No DEFAULT or UI configuration directive found! boot: Regards Jens Quote Link to comment
Frank1940 Posted June 29, 2016 Share Posted June 29, 2016 Describe what is happening as you go through the boot process. Are you seeing the boot choices screen and the notice that you are unpacking(?) bzimage and bzroot? If it is getting that far, you might want to run chkdsk on your flash drive. 1. Computer boots showing bios alternatives (F2 & F10) 2. Computer shows the following message SYSLINUX 4.03 2010-10-22 EED Copyright © 1994-2010 H. Peter Anvin et al Error: No configuration file found No DEFAULT or UI configuration directive found! boot: Regards Jens IF no one else jumps in you may want to go to this WIKI: http://lime-technology.com/wiki/index.php/Upgrading_to_UnRAID_v6 Be sure to make a backup of your flash drive BEFORE you go any further!!!!!!! (Hopefully, you also followed LimeTech instructions to make a backup of your flash drive before you started.) There are some trouble shooting hints for the plugin in the third paragraph and you might find some help there. However, I suspect that you might be better served to reformat you flash drive and do an new install of unRAID 6.1.9. There are instructions on which configuration files you should copy over from the backup that Limetech recommended However, you will have to look for them if you have to use that backup that I told you to make since the plugin moved things around. Quote Link to comment
shootking Posted June 29, 2016 Share Posted June 29, 2016 Hello As long as I can use the data on the drives, I dont mind doing a fresh install. I will read the wiki and see if I cna figure out how to get the fresh install to work with my drives. Regards Jens Quote Link to comment
cantharides999 Posted July 7, 2016 Share Posted July 7, 2016 I've followed the procedure today on my unraid 5.05 config,but it doesn't seem to work. I get a problem with the vallidation of the certificate. In short this is the error message I get after using the wget cmd.: 'WARNING cannot verify raw.githubusercontent.com certificate and afterwards I get a HTTP 400 bad request.'" The manual download of the unRAISserver.plg didn't help either. Rebooting the server doesn't result in downloading unraid v6. ?? Quote Link to comment
Frank1940 Posted July 7, 2016 Share Posted July 7, 2016 I've followed the procedure today on my unraid 5.05 config,but it doesn't seem to work. I get a problem with the vallidation of the certificate. In short this is the error message I get after using the wget cmd.: 'WARNING cannot verify raw.githubusercontent.com certificate and afterwards I get a HTTP 400 bad request.'" The manual download of the unRAISserver.plg didn't help either. Rebooting the server doesn't result in downloading unraid v6. ?? You might be better served to do a manual upgrade. Here is a thread with instructions on how-to-do-it: http://lime-technology.com/forum/index.php?topic=39032.0 At the bottom of the first post, you will find a link to a upgrade WIKI that has even more information including solutions to about every problem which folks encountered in earlier upgrades. (The simpler your configuration is, the less likely you are to have a problem!) The most important instruction is make a backup of your current Flash Drive BEFORE you start!!!!!!! Quote Link to comment
cantharides999 Posted July 7, 2016 Share Posted July 7, 2016 Thats what I did now, but now the system doesn't recognize my license key. Forget what I said. Copied the wrong file to the wrong place. Everything seems to be working real fine now. Thx for your help. Quote Link to comment
Frank1940 Posted July 7, 2016 Share Posted July 7, 2016 Thats what I di now, but now the system doesn't recognize my license key. I've put in the config folder as explained in the wiki, but it doesn't seem to work. What version did you upgrade to? Version 6.2 beta series requires that the registration be verified on boot by accessing the unRAID server. (This is is to assure that if they release a beta version that can endanger data, unRAID can stop the system from booting.) You seem to having some issues with access the Internet from your unRAID server. Post up a diagnostics file if you can get to 'Tools', 'Diagnostics' icon. Quote Link to comment
UncleOllie Posted November 11, 2016 Share Posted November 11, 2016 The upgrade didn't go well I had to revert back to 5.0-beta14. I ran method 2. First I got error "Could not find kernel image: linux". So I copied "syslinux" from "unRAIDServer-6.2.4-x86_64.zip" onto the USB stick. Upon rebooting again the first error was gone and I was getting "SYSLINUX 3.7.2 2008-09-25 EBIOS Copyright © 1994-2008 H. Peter Anvin". It was just stuck there never moving. Has anyone had similar issues and do they have any suggestions? Quote Link to comment
Frank1940 Posted November 11, 2016 Share Posted November 11, 2016 The upgrade didn't go well I had to revert back to 5.0-beta14. I ran method 2. First I got error "Could not find kernel image: linux". So I copied "syslinux" from "unRAIDServer-6.2.4-x86_64.zip" onto the USB stick. Upon rebooting again the first error was gone and I was getting "SYSLINUX 3.7.2 2008-09-25 EBIOS Copyright © 1994-2008 H. Peter Anvin". It was just stuck there never moving. Has anyone had similar issues and do they have any suggestions? Here is an introductory thread that will point you to several other resources to assist you through this problem. You are probably one of the folks who had to reformat their Flash Drives and install the new version. DON'T PANIC. If you follow the directions, you will not lose your configuration settings. https://lime-technology.com/forum/index.php?topic=41003.0 I will tell you right now, none of your plugins will work so be prepared for that. Quote Link to comment
RobJ Posted November 11, 2016 Share Posted November 11, 2016 The upgrade didn't go well I had to revert back to 5.0-beta14. I ran method 2. First I got error "Could not find kernel image: linux". So I copied "syslinux" from "unRAIDServer-6.2.4-x86_64.zip" onto the USB stick. Upon rebooting again the first error was gone and I was getting "SYSLINUX 3.7.2 2008-09-25 EBIOS Copyright © 1994-2008 H. Peter Anvin". It was just stuck there never moving. Has anyone had similar issues and do they have any suggestions? For a version that old, there were extra instructions, and I strongly recommend reading the Upgrading to UnRAID v6 guide, even if you wish to use the plugin to upgrade. You copied syslinux, but I can't tell if you cleaned out the old syslinux files, and you don't mention running make_bootable, something you HAVE to do if you switch syslinux files. For your old version, you are also going to have to run New Permissions. I believe the instructions for the upgrade plugin assume that the user has kept up to date, at least running v5.0, and you were still on an old beta. Quote Link to comment
UncleOllie Posted November 13, 2016 Share Posted November 13, 2016 Thanks everyone. I have the system up and running v6.2.4 now. Quote Link to comment
UncleOllie Posted November 13, 2016 Share Posted November 13, 2016 I do have one question. I set a share to private, created a user set read/write permissions to that share. But on my windows 7 pc when i try to navigate to that share it's saying I don't have access when i put the user name and password. Did I miss anything? Quote Link to comment
RobJ Posted November 14, 2016 Share Posted November 14, 2016 I do have one question. I set a share to private, created a user set read/write permissions to that share. But on my windows 7 pc when i try to navigate to that share it's saying I don't have access when i put the user name and password. Did I miss anything? I'm going to suggest starting a new support topic in the General Support board. Permissions issues with Windows are somewhat common, and I'm sure someone will have the answer you need. Be sure to add your diagnostics, see -> Need help? Read me first! Quote Link to comment
Fireball3 Posted November 14, 2016 Share Posted November 14, 2016 I do have one question. I set a share to private, created a user set read/write permissions to that share. But on my windows 7 pc when i try to navigate to that share it's saying I don't have access when i put the user name and password. Did I miss anything? I'm pretty sure this is what you are looking for. https://lime-technology.com/forum/index.php?topic=26412.msg231122#msg231122 Quote Link to comment
Frank1940 Posted November 14, 2016 Share Posted November 14, 2016 I do have one question. I set a share to private, created a user set read/write permissions to that share. But on my windows 7 pc when i try to navigate to that share it's saying I don't have access when i put the user name and password. Did I miss anything? I'm pretty sure this is what you are looking for. https://lime-technology.com/forum/index.php?topic=26412.msg231122#msg231122 Perhaps LimeTech should put this information into the user manual(s) so that it is more easily found. The explanation in the link explains the problem, the why-and-how, and the solution in a few lines. The way Samba handles this whole user name/password thing is extremely convoluted and I have never seen a clearer explanation about it in any place else! Quote Link to comment
UncleOllie Posted November 14, 2016 Share Posted November 14, 2016 Awesome it's all fixed thanks everyone! Quote Link to comment
Pro-289 Posted January 19, 2017 Share Posted January 19, 2017 I used method 1 on a 5.0.4 that was running for a long time. I uninstalled my Dynamix plugins just in case. Everything went perfectly. I now have 6.2.4 with all my shares and user logins. It decided to do a parity check after the first boot. Only 7 hours remaining. It booted a lot faster than 5.0.4. There used to be one area it would get stuck at during boot for about 1 minute. One question about the "build-in" Dynamix? It doesn't seem to be live updating anything. The dashboard works and shows live CPU usage, but the Main page doesn't update. I have to keep pressing F5 to refresh the screen and show the current progress/stats. I liked the old Dynamix in 5.0.4, everything updated in realtime. Something strange I've noticed about the update. I've opened two browsers to the Main page, IE and Firefox. During a parity check they both have the same status, nothing changes. But if I press F5 in either of my browsers to refresh the page, not only does that browser page update, but the other browser page also updates. It's like me pressing F5 forces unRAID to spit out a page update. Anyone seen anything like this? Thanks a lot for everyone's hard work. Quote Link to comment
RobJ Posted January 19, 2017 Share Posted January 19, 2017 One question about the "build-in" Dynamix? It doesn't seem to be live updating anything. The dashboard works and shows live CPU usage, but the Main page doesn't update. I have to keep pressing F5 to refresh the screen and show the current progress/stats. I liked the old Dynamix in 5.0.4, everything updated in realtime. By this method, you've done the mechanics of the upgrade, but you haven't been introduced to all the changes and settings. For that, I still recommend reading the Upgrading to UnRAID v6 guide. You can skip down to the Boot and test section for some notes, but I'd still skim through the first parts, as there are some helpful notes scattered through it. Then read the following sections, especially about the Display settings. And turn on Notifications. I personally think that users that shortcutted the upgrade are left a bit high and dry, as there's a lot to learn about the new stuff in v6. The upgrade guide is a little dated though, written for v6.0, and we're now at v6.2, beta testing v6.3. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.