itimpi Posted October 8, 2020 Share Posted October 8, 2020 1 minute ago, Rovivrus said: Sorry I have not replied sooner, This week end I have put time aside to put swap out the power supply for a brand new 1000w power supply to rule out power. so I hope by late Saturday/Sunday to rule out power as the issue, I will certainly keeping XMP disabled. if it still locks up then I will be trying another route. But I do have one question would I need to acquire another license key? due to the guides from the main site cover moving a key over to a key with the same version in case of failing flash drive. and in the pricing upgrading is permitted but it doesn't mention downgrading? Once you have a licence it is valid for any Unraid release. Link to comment
Rovivrus Posted October 8, 2020 Author Share Posted October 8, 2020 Thanks for that, and it is the same process of copying the web link across from the email to the unraid server? (sorry if it is a too obvious question). Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 Hello, a little later than planned but I have Just started the array and we at 0.2% if it locks up once again it is not memory or power because yesterday I swapped out the 750watts to a 1000wat power supply and now the drives are sharing 4 of the 6 leads and then we have 1 for the x4 fans and lights. and one for the usb3 pic express card. so fingers crossed that is all sorted out. Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 I have just seen the estimated time to finish. Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 No still locking up, at 0.6% 14minutes in. Is there something else that I could be missing? Link to comment
trurl Posted October 11, 2020 Share Posted October 11, 2020 Are you using the server for anything else during this? Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 It was through the web browser on another machine and it had 3 tabs one was the router to get the ip of the Unraid machine, another with this page open and the last the was the unraid web gui. I have not set anything else up as of yet. I have been unable to complete the 1st parity sync. the furtherest I have got is 0.6%. Link to comment
trurl Posted October 11, 2020 Share Posted October 11, 2020 Did you ever get Syslog Server setup? Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 nope nothing like that Link to comment
trurl Posted October 11, 2020 Share Posted October 11, 2020 Why haven't you setup Syslog Server? What version of Unraid are you running now? Did you try the stable release? Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 used a windows machine to create the USB via the creator tool. and when it came to enter in the line key it locked up the second time around the key was entered and then locked up again! the third time I was half way through setup the drives (selecting which drive for parity,storage, cache etc then it locked up, after that I got to start the array for the 1st time, and at 0.3% it locked up at 5mins in. this then repeated. So then someone guided me to the diagnostics. then some else asked about hardware. Then we looked at XMP now that is disabled, someone suggested a power supply issue. Which is where we at now I switched the power supply yesterday and today I booted it and got to 0.6% and at 14minutes in. someone else suggested go to os 6.8. which I was going to look at after food. Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 at the moment it on 6.9 I have made a usb with 6.8 ready to try after tea. Since it is now so close to that time of day. Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 how do you transfer the licence key? Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 just found the replace key on the flash pane... but the unraid wave is taking its time. i hope it has not locked up again! Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 Okay something is wrong? it is saying the parity is invalid and on the main page it saying starting services but it has not I am not seeing the parity check?? but it seems that it has not crashed. What do I have to do? Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 sorry I forgot to add this screen grab to the lat post 1 minute ago, Rovivrus said: Okay something is wrong? it is saying the parity is invalid and on the main page it saying starting services but it has not I am not seeing the parity check?? but it seems that it has not crashed. What do I have to do? Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 and it has locked up once again on 6.8. Link to comment
JonathanM Posted October 11, 2020 Share Posted October 11, 2020 Ok. I think it's time to take a different attack. Do you have any data on the server yet? In your screenshots it appears to be a totally new setup. If there is nothing really set up yet, I'd like you to physically unplug all the drives except for the USB Unraid boot stick, and the two parity drives. Set a new config, with one of the drives as parity 1, and the other as data disk 1. See if it will complete a parity build. Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 yes, I have not put any data on there the only thing that I have done is change the name from the default. Link to comment
Rovivrus Posted October 11, 2020 Author Share Posted October 11, 2020 so set one of the 14tb as parity and other 14tb as data? I will give that a go tomorrow after work? Link to comment
JonathanM Posted October 11, 2020 Share Posted October 11, 2020 50 minutes ago, Rovivrus said: so set one of the 14tb as parity and other 14tb as data? I will give that a go tomorrow after work? Yep. I want to start eliminating variables. Link to comment
Rovivrus Posted October 13, 2020 Author Share Posted October 13, 2020 Hello. Sorry I did not get to looking at this yesterday. I disconnected all the sata drives apart from the parity drives and selected one of the parity drives on data 1 but it will not let me start an array because it is saying too many drives are missing? what do I do to get around this? Link to comment
JonathanM Posted October 13, 2020 Share Posted October 13, 2020 On 10/11/2020 at 4:06 PM, jonathanm said: Set a new config 1 hour ago, Rovivrus said: what do I do to get around this? tools, new config Link to comment
Rovivrus Posted October 13, 2020 Author Share Posted October 13, 2020 Hello, Sorry I done the new config and just started it going. One 14tb as Parity 1 and the other 14tb as data 1. Link to comment
JonathanM Posted October 13, 2020 Share Posted October 13, 2020 2 minutes ago, Rovivrus said: just started it going. We'll have a result soon, since previous runs wouldn't go beyond half an hour. Link to comment
Recommended Posts