Jump to content

urhellishntemre

Members
  • Content Count

    10
  • Joined

  • Last visited

Community Reputation

0 Neutral

About urhellishntemre

  • Rank
    Member
  • Birthday 08/28/1991

Converted

  • Gender
    Male
  • Location
    California

Recent Profile Visitors

107 profile views
  1. When you had it enabled, and you went to start a transcode would it crash your system? I replaced my motherboard last weekend and have been trying to get back to stable. All the times I get a transcode started again with the correct set up, it hangs the full system, and I have to hit the reset button. I am trying to figure out if it’s something I’m borking or a mobo issue, or something else. Disregard comment, I forgot to add the runtime variable to extra parameters. I are stupid.
  2. Okay, I picked up this board, and for the most part am doing good. The only thing I can't figure out is when my Windows 10 VM is set to BR0 it does not connect to the internet, but it connects with the virbr0. Obviously the draw back is to virbr0 is you can't manage unRAID with it since it's out of range of the network. I made sure default network bridge for the VMs is br0, the VM has BR0 selected as active, and both ethernet ports have a active ethernet connection. Is there something I am missing here to get VMs on the same network as the host machine?
  3. Do you happen to have an LSI SAS controller (or anyone who has this mobo have one)? I found out the the AsRock x399 Taichi has an issue with the LSI controllers where it just resets them constantly, and requires a BIOS fix to come out for it. No news from AsRock on eta or if they will fix it, but I am looking into getting a different mobo that supports SAS controllers. Does the DESIGNARE support a sas controller?
  4. Does this apply to the 2920X as well? I was having hard crashes every 4 days, but it seemed like it was plex crashing, from the few logs that were actually being saved (plex fatal error script not found or something like that). If this applies to me too, then I wonder if one caused the other (I had 2 NVIDIA GPUs, and added a third for transcoding.) Anyways, this is the first time I’m hearing of this flag being used. Is it placed in the go file, or MAIN > Flash Drive, flags?
  5. Hahaha, yes it is. I can see the issue now. I will update later.
  6. Yes one is set to auto start. Should I go back to base 6.7, disable auto start and go back to NVIDIA?
  7. I installed the driver, and rebooted, but when I try to open my VMs page (or even VM settings) it won’t load. My VMs don’t even start. Is there something I’m missing? Something else I noticed is that on my Dashboard page, none of my VMs or Dockers show in the spots. When I install regular unRAID 6.7 everything works fine. NVIDIA unRAID 6.7.
  8. I wanted a stable system so I just got a Samsung Evo Plus.
  9. I found another SSD that uses the SM2263 controller, but the patch in 6.7.0-rc5 doesn't work. It's an Intel SSD 660p, internal error: qemu unexpectedly closed the monitor: 2019-03-02T07:23:43.702484Z qemu-system-x86_64: -device vfio-pci,host=08:00.0,id=hostdev2,bus=pci.0,addr=0x8: vfio 0000:08:00.0: failed to add PCI capability 0x11[0x50]@0xb0: table & pba overlap, or they don't fit in BARs, or don't align IOMMU group 15:[8086:f1a8] 08:00.0 Non-Volatile memory controller: Intel Corporation Device f1a8 (rev 03) Is there any other information that you may need to get it included? Thanks for all you do @limetech.
  10. I followed all the steps up until step up. I keep getting this error: /etc/rc.d/rc.pulseway start Starting Pulseway Daemon ... Error! I don't exactly know what I did wrong, but I even tried with a fresh config file, to make sure it wasn't one of the settings I changed. I just put in my username and password. Is there a spot where I can dig deeper for the logs?