Just now, Rysz said:

Yes, which command do you use on your UPS - beeper.disable or beeper.mute?

I am use beeper.disable

7 minutes ago, Owerrride said:

I am use beeper.disable

 

Put this into your /boot/config/go file:

at -M now + 3 minutes <<< "upscmd -u admin -p adminpass [email protected] beeper.disable 2>&1 | logger -t ups.beeper.disable"

 

You do not need to change anything in the line (normally), please try and let me know if it works.

If it doesn't work, you can check for the script response in SYSLOG searching for "ups.beeper.disable".

Note that it executes the command with a 3 minute delay so that the UPS is definitely connected by then.

1 hour ago, Rysz said:

You do not need to change anything in the line (normally), please try and let me know if it works.

If it doesn't work, you can check for the script response in SYSLOG searching for "ups.beeper.disable".

Note that it executes the command with a 3 minute delay so that the UPS is definitely connected by then.

Its working good! Thank you, but one beeeeeeep when AC returns stayed 😃

I wonder if I can just remove the beeper from the board?)

3 minutes ago, Owerrride said:

Its working good! Thank you, but one beeeeeeep when AC returns stayed 😃

 

Yes, that's normal, because it doesn't remember the disabled beeper and at that stage the command to disable it again hasn't been sent yet as Unraid is still shutdown.

 

2 minutes ago, Owerrride said:

I wonder if I can just remove the beeper from the board?)

 

I'd strongly advise against it, messing with the circuitry is not a good idea (unless you're an electrician or professional that's otherwise qualified to do so).

 

@Rysz We added some more values in pr #2620. If you will have chance please update privew. 

7 minutes ago, Masterwishx said:

@Rysz We added some more values in pr #2620. If you will have chance please update privew. 

 

Sure, I have a few other modifications cooking (see above) so it will probably be early next week. 🙂 

And thanks for the effort for the Eaton UPS, I'm curious to see how it will be on my 5P 850...

 

13 minutes ago, Rysz said:

And thanks for the effort for the Eaton UPS, I'm curious to see how it will be on my 5P 850...

Thanks, It's just adding more values for Eaton 9E in my case (which I tested) and other I hope, but more work needed to enable Bypass/ECO mode for Eaton. 

On 9/13/2024 at 1:51 PM, ich777 said:

Would it be possible to make this message also Dismiss-able:

 

Another idea from my side would be to make the plugin use tabs and to put the Controll Center in another tab (don't know if you like that but I think that would be super cool and would make the plugin page more accessible) :

 

On 9/14/2024 at 10:27 AM, Masterwishx said:

@Rysz We added some more values in pr #2620. If you will have chance please update privew. 

 

Done & Done in latest update (available now). 🙂 

I just noticed that my NUT plugin isn't able to start. I've attached my SYSLOG, can anyone help me find out what's stopping it from starting? TIA

 

Edit:it's working after stopping and starting the plugin but it would still be good to work out why it stopped so that I can prevent it from happening again

unraid-syslog-20240917-2030.zip

Edited September 17, 20241 yr by rama3124

The footer is no longer displaying battery percentages anymore. Is this a bug? The feature is enabled so I don't know why this is happening. The dashboard shows the status just fine. 

18 minutes ago, Sanderluc said:

The footer is no longer displaying battery percentages anymore. Is this a bug? The feature is enabled so I don't know why this is happening. The dashboard shows the status just fine. 

 

It works for me, what OS version are you on?
Did you try turning "NUT Page Footer" to "No" => Apply => "Yes"?

Did you try with another browser or after clearing your browser cache?

... or reinstalling the plugin (doesn't affect configuration), to see if that solves the problem for you?

 

 

@Rysz, Do you know if the new MIBs ever got posted for GitHub #2372 for the Eaton 9PX? They had asked to build it with the MIBs, but that is a little beyond my capability.

 

Or if the new versions have a better way to get this data over the network.

On 9/21/2024 at 12:42 AM, arghhh40k said:

@Rysz, Do you know if the new MIBs ever got posted for GitHub #2372 for the Eaton 9PX? They had asked to build it with the MIBs, but that is a little beyond my capability.

 

Or if the new versions have a better way to get this data over the network.

 

Thanks for the reminder, I managed to build a driver stub with the provided MIBs, hopefully as a starting point:

https://github.com/networkupstools/nut/issues/2372#issuecomment-2370448103

 

Can't promise I'll be able to get something up and running, if I do I'll ping you for testing (as I have no 9PX).

 

is `upsrw ` not working from unraid terminal ?

i got OK or Success but no value changed ...

1 hour ago, Masterwishx said:

is `upsrw ` not working from unraid terminal ?

i got OK or Success but no value changed ...

 

It works fine here, we just recently tested this with another user too.

What value are you trying to set?

5 minutes ago, Rysz said:

 

It works fine here, we just recently tested this with another user too.

What value are you trying to set?

 

yes i saw , but not working for me: 

 

upsrw -s input.transfer.low = 150 -u user -p pass Eaton9E2000i

and for new pr:

upsrw -s input.eco.switchable=high-efficiency -u user -p pass Eaton9E2000i

its wrote OK or Success with -w but not changing value ,

only `override.input.transfer.low = 150` in ups.conf and restart working

1 hour ago, Masterwishx said:

 

yes i saw , but not working for me: 

 

upsrw -s input.transfer.low = 150 -u user -p pass Eaton9E2000i

and for new pr:

upsrw -s input.eco.switchable=high-efficiency -u user -p pass Eaton9E2000i

its wrote OK or Success with -w but not changing value ,

only `override.input.transfer.low = 150` in ups.conf and restart working

 

Hmm, not sure about these values, but there's no difference in the `upsrw` program on Unraid.

The program itself works as on any other OS, so either a general program problem or one on the UPS side.

2 hours ago, Rysz said:

The program itself works as on any other OS, so either a general program problem or one on the UPS side.

 

OK ,will try to check with debug enabled if it will show ...

16 hours ago, Rysz said:

The program itself works as on any other OS, so either a general program problem or one on the UPS side.

After running with debug it seems i have a lot of `nut_libusb_get_interrupt: Connection timed out` , opened issue https://github.com/networkupstools/nut/issues/2643 for it ...

5 hours ago, Masterwishx said:

After running with debug it seems i have a lot of `nut_libusb_get_interrupt: Connection timed out` , opened issue https://github.com/networkupstools/nut/issues/2643 for it ...

 

Just to be sure, the default username/password combination in Unraid NUT is admin/adminpass, like this:

upsrw -s input.eco.switchable=high-efficiency -u admin -p adminpass Eaton9E2000i 

So unless you changed this to something different in `upsd.users`, user/pass as in your command will not work.

Hi!

 

I'm new here. Why am I not getting the battery charge info?

 

Edited September 28, 20241 yr by matic

Can the UPS commands be made optional via a setting. Also I think should be in User tools at the bottom rather than System Settings part.

11 minutes ago, SimonF said:

Can the UPS commands be made optional via a setting. Also I think should be in User tools at the bottom rather than System Settings part.

 

I'll put it on the TO-DO list for the next update, you're right "NUT Commands" should be under "User Utilities".

On 9/27/2024 at 3:37 PM, Rysz said:

 

Just to be sure, the default username/password combination in Unraid NUT is admin/adminpass, like this:

upsrw -s input.eco.switchable=high-efficiency -u admin -p adminpass Eaton9E2000i 

So unless you changed this to something different in `upsd.users`, user/pass as in your command will not work.

Yes I have defaults, Thanks will check it