chansearrington

Can someone tell me where in the logs I can see what's causing this error? Attached is my diagnostic export the-ark-diagnostics-20240114-1826.zip

@JorgeB Thanks. I restarted and I'm currently running the job again. I'll post back when it's finished. Currently at 57%

Only one.

Yes, that’s another server (Cronos). I’m working on fixing that one as well. But the server that I experienced this bug on is “the Ark” ignore “Cronos” for this bug thread. on “the Ark”, I followed the docs for parity swap to add a larger new parity drive, and move the old parity drive to replace another failing drive. https://docs.unraid.net/legacy/FAQ/parity-swap-procedure/ After a ~48 hour "copy" process, I watched the copy process go from 98 to 100%. Then a couple minutes later the array updated to show "Stopped. Upgrading disk/swapping parity" which is expected according to the document. However, it does not show the "START" button. Instead, it is still presenting the "COPY" button with copy information/checkbox. (See screenshot above)

@trurl / @JorgeB So Sorry. I uploaded the diagnostics of the wrong Unraid Server. Here's the correct one. the-ark-diagnostics-20231217-0745.zip

@JorgeB it for sure was done. This is what the screen showed after it hit 100%

@trurl I just experienced the same. I added a new drive (sdx) to be the new parity drive and assigned me old parity (SDC) to a failed drive spot. I then waited for 2 days for the copy parity to complete but the start button doesn't show like it says in the docs, just as @carlosliu highlighted Here is my diagnostic file. cronos-diagnostics-20231216-2344.zip

@jrmcmillan most of what I’ve read / found online about this problem points to using a reverse tunnel like CloudFlare Tunnel, BUT CloudFlare doesn’t allow you to use media apps like Plex in their tunnel. i found another service called LocalXpose that does the same thing, but I don’t know how to set it up on UnRaid. It has a docker image, but I don’t understand how to just use a docked image on UnRaid. I typically install everything via the store and their isn’t a LocalXpose app in there.

@jrmcmillan I recently switched to T-Mobile Home Internet and I’m looking to solve the same problem. did Tailscale help you directly connect to Plex? I can get my Plex to connect remotely, but it’s not a “direct connection” and is limited to 480p

@corvo? did you find a solution to this?

There's prompt for an update

Did you get this resolved?

@parsec have you looked into Duplicati or rClone for this? I don't know much about either, but I'm about to look into doing the same for OneDrive Offload to Unraid.

@dkerlee any news on this?

@noski thanks! I'm definitely not an expert in this area. I decided to go the same route as everyone else and just get a DS4246 from here -> https://www.ebay.com/itm/202404952486 I assume that what you are talking about doing would work the same, but I don't know. If yours works the same as mine, I only connected 1x cable from the Disk Shelf to my Server. Works fine. And I don't use the second disk manager module at all. Doing so, as I understand it, would make my disksehlf show up as two separate drives vs 1x combined one. Still not sure if this is how I should be doing it, lol.

@binhex I've got a question I can't seem to find an answer for. Long story short, I have to use a dedicated IP VPN. I'm moving from your delugeVPN to just deluge containers and routing those deluge containers through a single VPN container. Example: https://unraid-guides.com/2021/05/19/how-to-route-any-docker-container-on-unraid-through-a-vpn/ This works fine, the problem is that I currently run 3x separate instances of deluge ( Movies / Music / TV) I can get the Deluge containers to work one at a time, but not all 3x at once because they're all trying to use the same ports. In the docker templates, I have them all as different ports 58846, 58847, 58849 But docker templates are ignored when the connection is through another container And no matter how I try to define custom ports, these default ports are always defined.... somewhere. I've tried: Changing the ports in the deluge config template, they are ignored and set to the defaults Changing the ports in the deluge client settings, they are ignored, the defaults are still set in the container and it doesn't work Changing the ports in the deluge client config files, the defaults are still set in the container and it doesn't work No matter what, these defaults are the only thing that works no matter how I try to configure it. Where / How can I change these? Any ideas?

@Nexius2 yes, sort of. You need to install the local client desktop version of deluge on your PC/MAC. Then connect to the server. You can't create a torrent with the web client. There are probably other ways to do this, but this is how I do it.

@Squid gotcha. Is it possible to edit the container itself? If so, where/how?

@Squid it’s fine that they are ignored, but where are they defined? they are still read from somewhere. and it’s obviously not the client settings/client config files. it’s somewhere else between the client and docker

Is there another way I should be doing this?

I'm not sure how to even ask this question, so I'm hoping that the examples below will help articulate the problem. I have 3x separate containers of Deluge running and I'm trying to map them all through a NordVPN container. I can get the Deluge containers to work one at a time, but not all 3x at once because they're all trying to use the same ports.... I guess. So if I try to access them locally (192.168.1.4:[port]) it doesn't work. In the docker templates, I have them all as different ports 58846, 58847, 58849 But no matter how I try to define custom ports, these default ports are always defined.... somewhere. I've tried: - Changing the ports in the deluge config template, they are ignored and set to the defaults - Changing the ports in the deluge client settings, they are ignored, the defaults are still set in the container and it doesn't work - Changing the ports in the deluge client config files, the defaults are still set in the container and it doesn't work No matter what, these defaults are the only thing that works no matter how I try to configure it. Any ideas? Any ideas?

I have 3x separate instances of deluge running and I'm trying to map them all to NordVPN by following all the instructions provided here. However, no matter how I try to define custom ports, these default ports are always defined. I've tried: - Changing the ports in the config template - Changing the ports in the client settings - Changing the ports in the client config files No matter what, these defaults are the only thing that works no matter how I try to configure it. Any ideas?

Resetting my password to something without special characters and then disabling MFA made it work for me today.

@dkerlee where did you land on this? I'm trying to figure out the same thing for multiple family users.

@Alby24 did this bug ever get resolved?