Jump to content

JorgeB

Moderators
 View Profile  See their activity

  • Posts

    67,771

  • Joined

  • Last visited

  • Days Won

    708

 Content Type 

Everything posted by JorgeB

  1. JorgeB
    Sorry, I missed the part where you precleared the drives, so there are no partitions, to make sure everything is wiped run blkdiscard /dev/sdX on all three, then add them to the array and post new diags if it still complains.
  2. JorgeB
    Formatted with type 1 protection You need to remove that, see below for more info: https://forums.unraid.net/topic/93432-parity-disk-read-errors/?do=findComment&comment=864078
  3. JorgeB
    Pretty sure the mover now supports sparse files, so files like vdisks and docker image are "re-sparsified".
  4. JorgeB
    Also note that if you get one a day or so it's not ideal but not a big deal, constant errors are more of a problem since they will impact performance.
  5. JorgeB
    Yes, most likely the backplane. No, RAM won't cause UDMA_CRC errors, they are a communication problem, can only be the controller, cable/connection or the disks, disks is very rare.
  6. JorgeB
    They are in a pool, see below, it's the same procedure, when it says to assign the devices to the same pool assign them to the pool you want to have the current data once this is done. https://forums.unraid.net/topic/121365-my-appdata-system-and-domains-are-on-de-wrong-cache/?do=findComment&comment=1109614
  7. JorgeB
    You can enable the syslog server and then post that after a crash to see if there's anything logged, but if it's a hardware issue there probably won't be.
  8. JorgeB
    If it's happening with multiple disks, and since and understand the cables were replaced number one suspect would be the backplane, after that the controller itself, not the firmware, AFAIK that firmware has no known issues, and it's same I'm using, though if it it was the controller I would expect errors in all disks.
  9. JorgeB
    That's the theoretical max, actual max is around 3400MB/s, should be similar to the 9300-8i in that situation, still more than enough for 8 HDDs. Yes, just keep in mind that those slots go through the DMI, together with the onboard SATA ports/most M.2 slots, so bandwidth is shared, unlike the x16 CPU slot and M.2 slot 1 that go directly to the CPU, but since DMI for Z690 is PCIe 4.0 x8 it should be fine for all you need.
  10. JorgeB
    They probably are, please post the diagnostics.
  11. JorgeB
    Device was part of a pool, if there's no data there just re-format.
  12. JorgeB
    Possibly existing SSDs were formatted with the old partition layout, post the output of: fdisk -l /dev/sdX for both array devices.
  13. JorgeB
    Try the 2nd option, btrfs restore.
  14. JorgeB
    Like mentioned if the boot freezes in safe mode you likely have some hardware issue, would need to be onsite to be able to help, also I frequent the forum mostly when at work and time permits, can't really be doing one on one sessions with teamviwer or similar since I can't allot time for that.
  15. JorgeB
    Was this a new installation or you used the old config? If it wasn't a new installation try booting with one, using a trial key, and again if safe mode or a new trial flash drive freezes you have some hardware issue, can't really help remotely.
  16. JorgeB
    Nowhere in that did you mentioning booting in safe mode.
  17. JorgeB
    Seems unnecessary to me, though if you rebuild to a spare is always safer, since you still have the old disk intact if something goes wrong.
  18. JorgeB
    Wasn't that the GUI boot? If safe boot freezes you have some serious issue, or a bad flash drive.
  19. JorgeB
    Try booting in safe mode.
  20. JorgeB
    Cache pool dying should have nothing to do with GUI access, start by disabling SSL, edit config/ident.cfg on the flash drive and change USE_SSL from "auto" to "no", then reboot, see if you can access the GUI using the IP address.
  21. JorgeB
    Try btrfs restore, or upgrade to v6.10 since there is a new rescue=all option like mentioned in the link that might work for ro mount, and you just need to do it for one of the devices, it's all the same pool, if one doesn't work the others also won't.
  22. JorgeB
    Doubt that very much, I remember seeing before some Mellanox MACs being detected twice, 99.99% it's not an Unraid problem, basically confirmed by you having the same issue with v6.9.2, there are many users using those NICs with Unraid.
  23. JorgeB
    Look for a firmware update, it's not a general issue, I have several of those and they are working fine, e.g.: [15b3:1003] 01:00.0 Ethernet controller: Mellanox Technologies MT27500 Family [ConnectX-3]
  24. JorgeB
    Diags are after rebooting so we can't see what happened, disk looks healthy so I would recommend replacing/swapping cables to rule those out then rebuild on top. https://wiki.unraid.net/Manual/Storage_Management#Rebuilding_a_drive_onto_itself
  25. JorgeB
    https://forums.unraid.net/topic/86337-are-my-smart-reports-bad/?do=findComment&comment=800888
×
×
  • Create New...