mbc0

Hi, I quite a few Toshiba drives that are all fine but I have bought 4 in the last 3 months, one was DOA (Screaming Noise) and the other 3 all have Reallocated Errors and or CRC Errors Here are the 3 reports, would be good to know if I should try to RMA them or not? Thank you unraid2-smart-20220324-1521.rar

Hi, I have bought 3 X300 Drives over the last 3 months and all have CRC & Reallocation errors, they were in a different server until last week so I have acknowledged the errors in my new server and will see if they increase. Is this anything to worry about do you think? I have not seen (but also probably not looked before) on brand new drives? SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 4937 4 Start_Stop_Count -O--CK 100 100 000 - 22 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 8 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 096 096 000 - 1879 10 Spin_Retry_Count PO--CK 100 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 22 191 G-Sense_Error_Rate -O--CK 100 100 000 - 12 192 Power-Off_Retract_Count -O--CK 100 100 000 - 15 193 Load_Cycle_Count -O--CK 100 100 000 - 1111 194 Temperature_Celsius -O---K 100 100 000 - 31 (Min/Max 17/47) 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 23 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 096 096 000 - 1674 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 569 240 Head_Flying_Hours P----- 100 100 001 - 0

Thanks for your help, this has now been dealt with by Limetech as they gave me a licence transfer url

Hi, Thanks for the reply, I had been through those but the issue is with the internet, A VM won't start unless the array is started so I am in a catch 22 situation, I feel like I have painted myself into a corner 🙂

Hi, I have built a replacement server using a trial key and everything is now how I want it except the licence! This new server runs a Sophos XG Firewall VM so provides internet to the house and obviously if I shut it down I will not be able to start it again as there will be no interet (this server replaces the old server that used to run Sophos) How can I transfer the licence to this new server without internet? Can I copy the plus.key in place of the trial.key? Thanks in advance!

@ghost82 @ich777 Confirmed all working on 6.10.0-RC3 Thank you both so much for your time! hugely appreciated!

Am trying this now, thank you

I think I fell into the trap on this thread as it is titled current, maybe that thread title can be changed if it is not current? This is where it states you need 6.9.0 RC2 & up and being on 6.9.2 and the fact I read the title of the thread as current. CURRENT/NEW - UNRAID HP PROLIANT EDITION - RMRR ERROR PATCHING

Thank you, it states 6.9.0 RC 2 and up and I am on 6.9.2 so I presume the patch is included? Hopefully @ich777 can confirm? Thanks again for your time!

Thank you for your reply, I had already discussed the problem with @ich777 here He asked me to post in VM Support as he thinks it is not an RMRR issue?

Hi, Thanks so much for your time and the link, I have followed everything that user had done but still cannot start a VM (Any VM) with group 11-14 CPU Mode, Machine type or Bios make no difference sadly, Is it possible that this card will not pass through? could it be that I need a different card? I see others have successfully passed through but maybe not for my hardware setup? Again, thanks!

Thank you, I created a post in VM support yesterday on your advice, many thanks for your time!

Thanks, I appreciate it! so many hours on this now, would love to know what is wrong. tower-diagnostics-20220312-2018.zip

Hi, I have a 4 port NIC which I have managed to seperate on my HP Gen 8 Microserver using downstream all 4 ports are passed through but if I select any one of them (or all 4) I get the Execution error below. I have tried VFIO allow unsafe interrupts also with no change. Can anyone offer any advice please? Many thanks! tower-diagnostics-20220312-2018.zip

OK, thank you anyway, I did what you said and all 4 ports are now tickable and available in the VM but I still get an error when starting the VM

Hi, yes it is a quad gigabit card, I have tried singularly passing through ports 12-14 (11 is greyed out) I have removed the card and now the 2 ports on the Gen8 are showing in group 11 is that what you mean? does unraid HAVE to use 11? When you say bind all the NICS that I want to pass through on the 4 port card, do you mean within unraid network settings? Thank you This is the list with the Quad NIC removed This is with the QUAD NIC installed

Thank you, that makes sense now 🙂 Unfortunately I still have the problem internal error: qemu unexpectedly closed the monitor: 2022-03-12T11:53:40.135099Z qemu-system-x86_64: -device vfio-pci,host=0000:07:00.2,id=hostdev0,bus=pci.3,addr=0x0: vfio 0000:07:00.2: failed to setup container for group 13: Failed to set iommu for container: Operation not permitted It does this for groups 12-14 (for some reason I cannot select group 11?) What is annoying is I did this years ago successfully with the same hardware and I have resurrected the microserver. I have entered the command as shown Any ideas what could be the problem? Thank you tower-diagnostics-20220312-1158.zip

@ich777 Thank you for your reply 🙂 I cannot see the changelog link? Maybe this will help me and others if this topic is modified to day it is not in use? I went from this post to this post titled New & Current Method On this post there is no mention of a change? it is read as it is titled as current method Thank you for letting me know I just need to add intel_iommu=relax_rmrr to my syslinux.cfg but if I click the link to github that you provided the syslinux.cfg looks completely different to mine? do I just put intel_iommu=relax_rmrr at the end? I cannot find any documentation for this? This is my syslinux.cfg default menu.c32 menu title Lime Technology, Inc. prompt 0 timeout 50 label Unraid OS menu default kernel /bzimage append pcie_acs_override=downstream initrd=/bzroot label Unraid OS GUI Mode kernel /bzimage append pcie_acs_override=downstream initrd=/bzroot,/bzroot-gui label Unraid OS Safe Mode (no plugins, no GUI) kernel /bzimage append initrd=/bzroot unraidsafemode label Unraid OS GUI Safe Mode (no plugins) kernel /bzimage append initrd=/bzroot,/bzroot-gui unraidsafemode label Memtest86+ kernel /memtest Thank you so much for your time!

Hi! I would love to get this rmmr patch running on my Gen8 Microserver, I am currently running 6.9.2 so cannot see the kernal helper in the app section, would it be visible if I changed to 6.10.0-rc3? there are no other options in the update os branch? The prerequisite is 6.9.0 RC 2 and up I would have thought that would have included 6.9.2? The purpose for me is to pass through a 4 port network card Many thanks

Hi! I would love to get this running on my Gen8 Microserver, I am currently running 6.9.2 so cannot see the kernal helper in the app section, would it be visable if I changed to 6.10.0-rc3? there are no other options in the update os branch? Many thanks 🙂

Hi, I have been running this container for years, installed using the spaceinvader one guide but today installed fresh on a new server and need to be able to upload files several gigabytes in size. Is this file the only one I need to modify to enable that option? nextcloud/nginx/site-confs/default client_max_body_size Thank you

I also do have my local network specified in LAN_NETWORK

Sorry, forgot to say, radarr,sonarr etc are NOT using privoxy

Hi! Hope everyone has had a great Christmas! 🙂 Wondering if anyone can help please? I have just added the prowlarr container to privoxy and can acess it no problem but cannot find a way for prowlarr to commincate with sonarr/radarr I have tried http://sonarr:8989 http://radarr:7878 Can anyone offer any advice please? TIA 🙂

Hi! I noticed my phone was not uploading photos to my nextcloud and cut a long story short I could not access the server due to an internal error. I noticed that the config.php was refreshed (standard looking) so restored my config.php from a backup and now I am stuck at the update screen every time I boot? I cannot find a way get into my server without being presented with the update screen to 22.1.1? Nextcloud will be updated to version 22.1.1 The following apps will be updated: All I have is a start update button, there is no cancel or anything I can do to get out of this loop? Can anyone help please? Thank you