mgutt Posted September 16, 2022 Share Posted September 16, 2022 10 hours ago, DataCollector said: nur als Idee, da mit powertop auch massive Error im Array verursacht hatte: Gäbe es ein Problem mit powertop, dann wäre die Platte nicht mehr erreichbar. Er hat aber reallocated sectors. Das entsteht auf der Platte selbst ohne äußere Einflüsse. Quote Link to comment
hawihoney Posted September 16, 2022 Share Posted September 16, 2022 9 minutes ago, mgutt said: Er hat aber reallocated sectors. Genau gesagt hatte er "Current_Pending_Sector" und später durch Unraid angezeigte Errors. Beides verflüchtigte sich nach erneutem Lesen. Da es keine Verbindungsprobleme gibt (UDMA CRC) vermute ich, dass etwas dazwischen haut. Das System mal eine Weile ohne Plugins (hier Powertop) zu betreiben halte ich für einen validen Test. Irgendwie muss man das doch herausfinden können. Quote Link to comment
mgutt Posted September 16, 2022 Share Posted September 16, 2022 13 minutes ago, hawihoney said: Beides verflüchtigte sich nach erneutem Lesen. Pending, unallocated, Uncorrectable, usw spielt sich ausschließlich in der Firmware der HDD ab. Die Firmware bekommt die Info vom OS etwas in Sektor X zu lesen / schreiben und wenn das beim ersten Versuch nicht klappt, kommt es zum Pending. Wenn er den Sektor schlussendlich doch lesen kann, dann verschwindet die Meldung. Manchmal repariert die Firmware auch an Hand des ECC die Daten. Und wenn das nicht klappt, gibt es Uncorrectable Fehler im SMART. Ist der Sektor dagegen komplett tot, dann mappt die Firmware den Sektor neu. Da ist dann reallocated. Auf all das hat das OS keinen Einfluss. Selbst wenn es das wollte, geht es einfach nicht, weil die Firmware gar keine Schnittstelle dafür hat. 1 Quote Link to comment
frank80 Posted September 19, 2022 Share Posted September 19, 2022 Hallo, bis jetzt habe ich keine Fehler mehr erhalten. Ich habe vorgestern einen smartctl long Test gestartet. Hier werden, bis auf den Error 1 occurred at disk power-on lifetime: 5193 hours (216 days + 9 hours) keine Fehler mehr angezeigt. Spoiler root@unraid:~# smartctl -a /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba MG08ACA... Enterprise Capacity HDD Device Model: TOSHIBA MG08ACA16TE Serial Number: X1N0A0KSFVGG LU WWN Device Id: 5 000039 b38da0a4f Firmware Version: 0102 User Capacity: 16,000,900,661,248 bytes [16.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 19 22:06:19 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1428) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 095 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 8206 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1591 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 5299 10 Spin_Retry_Count 0x0033 100 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 91 23 Helium_Condition_Lower 0x0023 100 100 075 Pre-fail Always - 0 24 Helium_Condition_Upper 0x0023 100 100 075 Pre-fail Always - 0 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1879 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 25 (Min/Max 20/46) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 119668737 222 Loaded_Hours 0x0032 097 097 000 Old_age Always - 1356 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 536 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 5193 hours (216 days + 9 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 43 18 c8 e2 01 40 Error: UNC at LBA = 0x0001e2c8 = 123592 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 40 a0 90 f8 01 40 00 7d+00:14:44.584 READ FPDMA QUEUED 60 40 98 50 f3 01 40 00 7d+00:14:42.334 READ FPDMA QUEUED 60 40 90 10 ee 01 40 00 7d+00:14:42.331 READ FPDMA QUEUED 60 40 88 d0 e8 01 40 00 7d+00:14:42.326 READ FPDMA QUEUED 60 40 80 90 e3 01 40 00 7d+00:14:42.323 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended captive Interrupted (host reset) 90% 5267 - # 2 Extended offline Interrupted (host reset) 90% 5267 - # 3 Extended offline Aborted by host 90% 5232 - # 4 Short offline Completed without error 00% 5228 - # 5 Short offline Completed without error 00% 5191 - # 6 Extended offline Aborted by host 90% 5180 - # 7 Short offline Completed without error 00% 5179 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Was haltet ihr davon, sollte ich Toshiba mal anschreiben? Gruß Frank Quote Link to comment
DataCollector Posted September 19, 2022 Share Posted September 19, 2022 3 hours ago, frank80 said: was haltet ihr davon, sollte ich Toshiba mal anschreiben? Nein. Wenn ich mich nicht verlesen habe sind jetzt Reallocated_Sector_Ct Reallocated_Event_Count Current_Pending_Sector alle bei 0. Es sind also aktuell keine Probleme mit diesen relevanten Events verzeichnet. Die vorherig unklaren Sektoren wurden anscheinend als problemlos entschieden. Quote Link to comment
frank80 Posted September 21, 2022 Share Posted September 21, 2022 Ok, danke euch für die Hilfe!! Quote Link to comment
frank80 Posted September 22, 2022 Share Posted September 22, 2022 Hallo zusammen, ich glaube, ich habe mich zu frühe gefreut. Jetzt habe ich diesen Fehler und unRAID ist aktuell nicht erreichbar 😩 198 Offline_Uncorrectable 0x0030 001 001 000 Old_age Offline - 418 Spoiler root@unraid:~# smartctl -a /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba MG08ACA... Enterprise Capacity HDD Device Model: TOSHIBA MG08ACA16TE Serial Number: X1N0A0KSFVGG LU WWN Device Id: 5 000039 b38da0a4f Firmware Version: 0102 User Capacity: 16,000,900,661,248 bytes [16.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Sep 22 20:23:23 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1428) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 095 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 8188 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1614 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 5369 10 Spin_Retry_Count 0x0033 100 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 91 23 Helium_Condition_Lower 0x0023 100 100 075 Pre-fail Always - 0 24 Helium_Condition_Upper 0x0023 100 100 075 Pre-fail Always - 0 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1902 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 33 (Min/Max 20/46) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 001 001 000 Old_age Offline - 418 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 119668737 222 Loaded_Hours 0x0032 097 097 000 Old_age Always - 1373 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 535 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 5193 hours (216 days + 9 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 43 18 c8 e2 01 40 Error: UNC at LBA = 0x0001e2c8 = 123592 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 40 a0 90 f8 01 40 00 7d+00:14:44.584 READ FPDMA QUEUED 60 40 98 50 f3 01 40 00 7d+00:14:42.334 READ FPDMA QUEUED 60 40 90 10 ee 01 40 00 7d+00:14:42.331 READ FPDMA QUEUED 60 40 88 d0 e8 01 40 00 7d+00:14:42.326 READ FPDMA QUEUED 60 40 80 90 e3 01 40 00 7d+00:14:42.323 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5367 - # 2 Extended captive Interrupted (host reset) 90% 5267 - # 3 Extended offline Interrupted (host reset) 90% 5267 - # 4 Extended offline Aborted by host 90% 5232 - # 5 Short offline Completed without error 00% 5228 - # 6 Short offline Completed without error 00% 5191 - # 7 Extended offline Aborted by host 90% 5180 - # 8 Short offline Completed without error 00% 5179 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Quote Link to comment
hawihoney Posted September 22, 2022 Share Posted September 22, 2022 47 minutes ago, frank80 said: Offline_Uncorrectable Das ist die selbe Platte die zuvor Current_Pending_Sector auf 418 hatte? Die hat eine Macke. Erst Current_Pending_Sector=418, nach erneutem Lesen sind die wieder weg, jetzt Offline_Uncorrectable=418. Das wirkt nicht gesund. Selbst wenn das wieder weggehen würde, hätte ich kein Vertrauen mehr. Quote Link to comment
frank80 Posted September 22, 2022 Share Posted September 22, 2022 (edited) Hallo Members, ja, das ist die gleiche Platte. Also doch Toshiba anschreiben. Unraid hat sich wenigstens am Schalter ausschalten lassen. Jetzt hängt er zwar an Starting diagnostics collection, würde aber mal abwarten was passiert. Edited September 22, 2022 by frank80 Quote Link to comment
DataCollector Posted September 23, 2022 Share Posted September 23, 2022 8 hours ago, frank80 said: Also doch Toshiba anschreiben. Im ersten Step wird Garantie bei Toshiba Festplatten über den Händler abgewickelt, wenn diese Garantie haben. Grober erster Punkt für Garantiecheck: https://myapps.taec.toshiba.com/myapps/admin/jsp/webrma/addRequest1NoLogin.jsp Wenn der sich quer stellt springt Toshiba in die Bresche. https://www.toshiba-storage.com/contact/ Quote Link to comment
frank80 Posted September 24, 2022 Share Posted September 24, 2022 Hallo, wie lange geht so eine diagnostics collection, seit Donnerstag habe ich immer noch das gleiche Bild wie oben gepostet? Auf die Tastatur wird nicht reagiert. Quote Link to comment
DataCollector Posted September 24, 2022 Share Posted September 24, 2022 1 hour ago, frank80 said: Hallo, wie lange geht so eine diagnostics collection, Tools/Diagnostics (Erzeugen des ZIP) hat bei meinem 1st System gerade rund 40 Sekunden gebraucht. 1 hour ago, frank80 said: seit Donnerstag habe ich immer noch das gleiche Bild wie oben gepostet? Irritierend. Ich würde vermuten, da ist irgendetwas schief gelaufen/eingefrohren. 1 hour ago, frank80 said: Auf die Tastatur wird nicht reagiert. Wird auf die Mouse reagiert? Quote Link to comment
frank80 Posted September 24, 2022 Share Posted September 24, 2022 Hallo, nein. Er hängt beim booten, wie man auf dem Bild sieht. Ich glaube da hilft nur noch ein Reset?! Quote Link to comment
DataCollector Posted September 24, 2022 Share Posted September 24, 2022 1 minute ago, frank80 said: Er hängt beim booten, wie man auf dem Bild sieht. Das Bild zeigt den Bootvorgang? Also nicht die Diagnosticserstellung, wie Du sie direkt ueber dem Bild verlinkt hast? Ich hatte mich schon gewundert, weil der Tools/Diagnostics (ZIP Erstellungs) Vorgang irgendwie anders aussieht. 1 minute ago, frank80 said: Ich glaube da hilft nur noch ein Reset?! Ich würde es versuchen, ja. Quote Link to comment
hawihoney Posted September 24, 2022 Share Posted September 24, 2022 1 hour ago, frank80 said: wie lange geht so eine diagnostics collection Sehr schnell. Ein verlängernder Faktor ist die Anzahl der Festplatten und ob diese Spin-Down oder Spin-Up sind. Unraid fährt die Platten nämlich nicht alle auf einmal hoch sondern eine nach der anderen um dann deren SMART Werte zu ziehen. Gerade wer viele Platten besitzt sollte alle Platten vorab über den Button "Spin-Up" hochfahren. Dann geht es sehr schnell. Persönliche Anmerkung: Du hast offensichtlich eine sehr hohe Leidens-Toleranz was Deine Platte(n) angeht. Ich persönlich hätte das gesamte System in der Zeit sicherlich schon zweimal neu aufgesetzt und die Platte persönlich zu Toshiba gefahren. Auf diese Platte bzw. deren Anbindung würde ich schon lange nicht mehr vertrauen. Was hält Dich davon ab? Quote Link to comment
frank80 Posted September 24, 2022 Share Posted September 24, 2022 2 minutes ago, hawihoney said: Du hast offensichtlich eine sehr hohe Leidens-Toleranz was Deine Platte(n) angeht Naja, wie man es nimmt, ich habe aktuell ziemlich viel um die Ohren, das lenkt etwas ab 😅 Ich habe jetzt ein Reset gemacht und unraid ist wieder da. Aktuell läuft der Parity-Check. Ich habe die Platte beim Händler reklamiert, ist ja bis 2026 Garantie drauf! Gruß und danke für eure Hilfe! Quote Link to comment
mgutt Posted September 26, 2022 Share Posted September 26, 2022 Für so einen Fall den Syslog mirror aktivieren und nach dem Freeze beim Herunterfahren einen Kaltstart machen und die Logs auf dem USB Stick sichten. Quote Link to comment
frank80 Posted September 26, 2022 Share Posted September 26, 2022 Hallo mgutt, danke für die Info, ich habe Syslog jetzt aktiviert. Gestern Morgen war unraid auch nicht mehr erreichbar, auch direkt am Monitor hatte ich keine Reaktion. Es half nur noch ein Reset, dann kam der Parity-Check, als dieser heute fertig war, hat er ihn noch einmal gestartet. Bei der Platte habe ich aktuell wieder keine Fehler, das ist echt verrückt. Ich hoffe, ich bekomme die Platte ohne Probleme getauscht. Spoiler root@unraid:~# smartctl -a /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.10.28-Unraid] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba MG08ACA... Enterprise Capacity HDD Device Model: TOSHIBA MG08ACA16TE Serial Number: X1N0A0KSFVGG LU WWN Device Id: 5 000039 b38da0a4f Firmware Version: 0102 User Capacity: 16,000,900,661,248 bytes [16.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 26 18:51:24 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1428) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 095 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 8188 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1614 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 5463 10 Spin_Retry_Count 0x0033 100 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 91 23 Helium_Condition_Lower 0x0023 100 100 075 Pre-fail Always - 0 24 Helium_Condition_Upper 0x0023 100 100 075 Pre-fail Always - 0 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1903 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 39 (Min/Max 20/46) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 001 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 218759176 222 Loaded_Hours 0x0032 097 097 000 Old_age Always - 1464 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 528 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 5193 hours (216 days + 9 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 43 18 c8 e2 01 40 Error: UNC at LBA = 0x0001e2c8 = 123592 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 40 a0 90 f8 01 40 00 7d+00:14:44.584 READ FPDMA QUEUED 60 40 98 50 f3 01 40 00 7d+00:14:42.334 READ FPDMA QUEUED 60 40 90 10 ee 01 40 00 7d+00:14:42.331 READ FPDMA QUEUED 60 40 88 d0 e8 01 40 00 7d+00:14:42.326 READ FPDMA QUEUED 60 40 80 90 e3 01 40 00 7d+00:14:42.323 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5367 - # 2 Extended captive Interrupted (host reset) 90% 5267 - # 3 Extended offline Interrupted (host reset) 90% 5267 - # 4 Extended offline Aborted by host 90% 5232 - # 5 Short offline Completed without error 00% 5228 - # 6 Short offline Completed without error 00% 5191 - # 7 Extended offline Aborted by host 90% 5180 - # 8 Short offline Completed without error 00% 5179 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Quote Link to comment
frank80 Posted October 5, 2022 Share Posted October 5, 2022 Guten Morgen zusammen, wie löscht oder nullt ihr HDD´s richtig? Ich habe jetzt 3 Durchgänge mit Eraser und 1 Durchgang mit WipeDisk. EaseUS data Recovery findet immer noch Dateien. Quote Link to comment
mgutt Posted October 5, 2022 Share Posted October 5, 2022 32 minutes ago, frank80 said: wie löscht oder nullt ihr HDD´s richtig? dd if=/dev/zero of=/dev/sdX bs=4096 status=progress Wobei sdX durch die Bezeichnung der Platte ersetzt werden muss. Quote Link to comment
DataCollector Posted October 5, 2022 Share Posted October 5, 2022 (edited) On 10/5/2022 at 7:46 AM, frank80 said: Guten Morgen zusammen, wie löscht oder nullt ihr HDD´s richtig? Unter Unraid nehme ich PreClear unter Windows HDTunePro. Jeweils nur einmaliger Durchgang. Das bringt aber nur etwas, wenn die Festplatte eben noch funktioniert. Aufgrund der Verschlüsselung bei unraid (encrypted) oder dem Umstand, daß bei meinen Windows-HardwareRaid immer mehrere Festplatten beteiligt sind, ist bei Fehlern in diesen Konstellationen eine komplette Löschung nicht wirklich nötig. Deshalb habe ich auch keine Skrupel solch verwendete Festplatten, im Defektfall, auch ohne Löschung auf Garantie einzusenden. Edited October 6, 2022 by DataCollector Typos Quote Link to comment
frank80 Posted October 6, 2022 Share Posted October 6, 2022 Hallo, ich habe die HDD jetzt noch einmal mit diesem Befehl überschrieben. (sdX natürlich angepasst) dd if=/dev/zero of=/dev/sdX bs=4096 status=progress On 10/5/2022 at 10:59 AM, DataCollector said: unraid (encrypted) habe ich bei mir nicht gemacht. Danke noch einmal für eure Hilfe 👍 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.