binhex Posted October 5, 2016 Author Share Posted October 5, 2016 binhex - In have set my ip addresses to start at 10.10.1.1. I would think that should be the LAN network value. isnt it? ok, just so you know the LAN_NETWORK value you have is incorrect, it should be 10.10.1.0/24 No, 10.10.1.1 is a host ip address not a network address, the network address is signified by zeroing the octets that are defined by the mask and denotes your entire network, not a single host, so for example:- A CIDR mask of /24 converts to a mask of 255.255.255.0, so the network would be 10.10.1.0 (what you have) However you can have other masks, some people go a bit crazy and decide they need 65,536 networks, with each network supporting 65,534 hosts on their home lan :-), and thus have a CIDR of /16 which converts to mask 255.255.0.0 which then means (using your network scheme) a network of 10.10.0.0. I hope this helps, in short if your CIDR is /24 (mask 255.255.255.0) then just zero the last octet and be happy :-) Quote Link to comment
binhex Posted December 31, 2016 Author Share Posted December 31, 2016 I know I'm a little early, but happy new year to all, hoping 2017 will be an even better year!. Many thanks to everybody who helps out on the support threads and of course big thanks to all the donators. See you all in the new year. Sent from my SM-G900F using Tapatalk Quote Link to comment
arthur84 Posted February 3, 2017 Share Posted February 3, 2017 Hello, I'm trying to install arch-openvpn in docker but as there is no informations in the hub I've followed arch-delugevpn guide. But it is not working and nothing is created in the config dir and even supervisor.log is not here How can I make it work ? I can't find any simple and working solution for a proxy --> open vpn container. Sorry if I'm using wrong terms or anything else. Thank you for your help. Quote Link to comment
binhex Posted February 6, 2017 Author Share Posted February 6, 2017 Hello, I'm trying to install arch-openvpn in docker but as there is no informations in the hub I've followed arch-delugevpn guide. But it is not working and nothing is created in the config dir and even supervisor.log is not here How can I make it work ? I can't find any simple and working solution for a proxy --> open vpn container. Sorry if I'm using wrong terms or anything else. Thank you for your help. you cant install arch-openvpn, this is an intermediate docker image used as a base for the other vpn images i produce, if you want to get openvpn working to use as a safe tunnel for communicating with your lan then take a look at LSIO's docker image:- http://lime-technology.com/forum/index.php?topic=43317.0 Quote Link to comment
death.hilarious Posted February 7, 2017 Share Posted February 7, 2017 Private Internet Access introduced a new port forwarding API on February 2nd. Importantly: Keep in mind that this new API will be replacing the old one, and that the old API located at vpninfo/port_forward_assignment will be discontinued sometime soon. Quote Link to comment
binhex Posted February 8, 2017 Author Share Posted February 8, 2017 Private Internet Access introduced a new port forwarding API on February 2nd. Importantly: Keep in mind that this new API will be replacing the old one, and that the old API located at vpninfo/port_forward_assignment will be discontinued sometime soon. hmm ok going to have to dig into this, im not a big fan of the way PIA just pulls the plug on existing infrastructure, just hope its a bit smoother than their port change, thanks a lot for posting this. Quote Link to comment
Katherine Posted February 15, 2017 Share Posted February 15, 2017 Any chance we will see a NZBGet VPN docker? Quote Link to comment
whizfajita Posted August 31, 2017 Share Posted August 31, 2017 On 15.2.2017 at 9:11 PM, Katherine said: Any chance we will see a NZBGet VPN docker? Came here to ask the same question. I'm used to NZBGet and would like to use that instead of SABnzbdVPN. Quote Link to comment
jrdnlc Posted October 9, 2017 Share Posted October 9, 2017 @binhex Would love to see a Homebridge docker. The one out now is very unreliable. Quote Link to comment
tazire Posted March 12, 2018 Share Posted March 12, 2018 just wondering if there is any plan for a qbittorrentVPN docker? i'm very interested in changing from deluge if this is likely to in the pipeline? Quote Link to comment
binhex Posted March 13, 2018 Author Share Posted March 13, 2018 22 hours ago, tazire said: just wondering if there is any plan for a qbittorrentVPN docker? i'm very interested in changing from deluge if this is likely to in the pipeline? not at this time, no, i got too much going on im afraid, have you given rtorrentvpn a go?, not sure why you want to move off deluge, but rtorrent is in my experience pretty good, lots of features, very fast, and lightweight. Quote Link to comment
tazire Posted March 13, 2018 Share Posted March 13, 2018 5 hours ago, binhex said: not at this time, no, i got too much going on im afraid, have you given rtorrentvpn a go?, not sure why you want to move off deluge, but rtorrent is in my experience pretty good, lots of features, very fast, and lightweight. I could never get my deluge to use my full bandwidth. even to this day it never goes above 4mb/s dl. i gave rtorrent a go way back when you first released it. I just fancied qbittorrent because thats what i have experience with. I might go back to rtorrent and see how i get on. Thanks anyway Quote Link to comment
binhex Posted March 13, 2018 Author Share Posted March 13, 2018 (edited) 59 minutes ago, tazire said: I could never get my deluge to use my full bandwidth. even to this day it never goes above 4mb/s dl. i gave rtorrent a go way back when you first released it. I just fancied qbittorrent because thats what i have experience with. I might go back to rtorrent and see how i get on. Thanks anyway are you writing incompletes to the array directly?, or do you have a cache pool setup?, both of these can cause issues with performance, recommended to either write to a single cache drive (no mirror) or use the 'unassigned devices' plugin and write to an unassigned disk edit - also take a look here, Q5 for other possible reasons:- Edited March 13, 2018 by binhex Quote Link to comment
ezhik Posted March 15, 2018 Share Posted March 15, 2018 (edited) binhex-plexpass would not start: chown: cannot access '/opt/plexmediaserver/': No such file or directory Edit: This has been fixed. Edited March 15, 2018 by ezhik Quote Link to comment
tazire Posted March 19, 2018 Share Posted March 19, 2018 On 13/03/2018 at 5:23 PM, binhex said: are you writing incompletes to the array directly?, or do you have a cache pool setup?, both of these can cause issues with performance, recommended to either write to a single cache drive (no mirror) or use the 'unassigned devices' plugin and write to an unassigned disk I have an unassigned device that i use. I have also used the cache drive prior to that and still never had better than 4mb/s. i had this issue way back on first install and went through everything with you at the time. possible deluge settings etc. still having the same issues with rtorrent too... couchpotato says test successful but will not add any files for download. gonna have to try give that more time when i get the chance i think. Quote Link to comment
sreed77 Posted May 23, 2018 Share Posted May 23, 2018 I have tried everything I can thing read the faq 10 times checked the network and still no GUI at my wits ends as I love this docker https://pastebin.com/ZKSEzeqH supervisord.log ( hide my PIA account and password) what the heck I'm I missing Quote Link to comment
trurl Posted May 23, 2018 Share Posted May 23, 2018 4 minutes ago, sreed77 said: I have tried everything I can thing read the faq 10 times checked the network and still no GUI at my wits ends as I love this docker https://pastebin.com/ZKSEzeqH supervisord.log ( hide my PIA account and password) what the heck I'm I missing By looking at your pastebin I am guessing that "this docker" refers to delugevpn. The reason I had to guess is because this is not the support thread for any specific binhex docker. This thread is just a general binhex thread. Delugevpn docker has its own support thread, which you can get to very easily from the Apps tab or by clicking on the installed docker and selecting Support. As it says in the very first post of this thread: Quote Important - This thread is NOT for support of Docker images, please use the separate support threads shown in the "Docker Images" section shown further below Quote Link to comment
MDark Posted June 26, 2018 Share Posted June 26, 2018 I have downloaded your DelugeVPN and have that working just fine. I downloaded your sabnzbd and would like to route its traffic through DelugeVPN... But for the life of me, I just can't wrap my head around that process. Would it be possible for anybody on here to help me understand this process? Do I enter the port and my server IP somewhere in the sabnzbd container edit screen or do I do it within the webui? If it is the edit screen I am not sure where to put this information. Thanks for any support you can offer. Quote Link to comment
binhex Posted June 26, 2018 Author Share Posted June 26, 2018 6 hours ago, MDark said: I downloaded your sabnzbd and would like to route its traffic through DelugeVPN you cant do this, its highly restricted to prevent ip leakage, instead you need to install sabnzbdvpn, most vpn providers allow multiple connections and the overhead of 2 tunnels is suprisingly low. Quote Link to comment
MDark Posted June 26, 2018 Share Posted June 26, 2018 Appreciate the response. I just donated. Quote Link to comment
binhex Posted June 26, 2018 Author Share Posted June 26, 2018 3 minutes ago, MDark said: Appreciate the response. I just donated. Thanks for the donation. Quote Link to comment
MDark Posted July 2, 2018 Share Posted July 2, 2018 So I was able to get Binhex sabnzbd working but not sabnzbdvpn.... I get an execution error when I try to launch it after pulling it down but I also get an error when installing. Quote Link to comment
binhex Posted July 2, 2018 Author Share Posted July 2, 2018 54 minutes ago, MDark said: So I was able to get Binhex sabnzbd working but not sabnzbdvpn.... I get an execution error when I try to launch it after pulling it down but I also get an error when installing. Firstly this isnt a support thread, taken from first post in this thread:- Important - This thread is NOT for support of Docker images, please use the separate support threads shown in the "Docker Images" section shown further below. Your issue is due to the last line in the above screenshot, in short you have a port conflict, one or more of the ports you are trying to use is already in use by another container (most probably sabnzbd). Quote Link to comment
_0m0t3ur Posted September 13, 2018 Share Posted September 13, 2018 Not sure what's taken me so long to find this thread, but it's one of the best docker support threads I've seen. Thanks on a number of levels: thanks for this thread; thanks for supporting unRAID and it's users with your Docker containers. Hopefully my donation helps a little. Quote Link to comment
binhex Posted September 14, 2018 Author Share Posted September 14, 2018 13 hours ago, DoItMyselfToo said: Not sure what's taken me so long to find this thread, but it's one of the best docker support threads I've seen. Thanks on a number of levels: thanks for this thread; thanks for supporting unRAID and it's users with your Docker containers. Hopefully my donation helps a little. np, i really do appreciate the comment and donation!. Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.