Arcaeus Posted February 1, 2019 Author Share Posted February 1, 2019 Alright, I'll give that a shot here after I finish lunch and respond back with my findings. @Hoopster @Squid @trurl Thank you all so much for your help, I really appreciate it! Quote Link to comment
Arcaeus Posted February 1, 2019 Author Share Posted February 1, 2019 Alright, got back, installed the card, and it fired right up! So it seems like not having the drivers for the Bigfoot Killer network chip was the issue. Thank you all again for you help, I'm really excited to start using this. Quote Link to comment
Squid Posted February 1, 2019 Share Posted February 1, 2019 I would also post a feature req for LT to add in the appropriate drivers to unRaid Quote Link to comment
Arcaeus Posted February 1, 2019 Author Share Posted February 1, 2019 Sure. Is that done through Unraid, or how would I do that? Quote Link to comment
Squid Posted February 1, 2019 Share Posted February 1, 2019 https://forums.unraid.net/forum/53-feature-requests/ Quote Link to comment
Hoopster Posted February 1, 2019 Share Posted February 1, 2019 1 hour ago, Arcaeus said: Alright, got back, installed the card, and it fired right up! So it seems like not having the drivers for the Bigfoot Killer network chip was the issue. Glad to hear it is working now. It is a rarity to find a NIC not supported by unRAID. Good thing @Squid suspected this might be the case and pointed you in the right direction. Quote Link to comment
Stream Arcanine Posted October 3, 2019 Share Posted October 3, 2019 (edited) I seem to having the same exact problem too. ipv4 / ipv6 adress not set. I will follow your advices Edited October 3, 2019 by Stream Arcanine Quote Link to comment
Dudedawg Posted November 19, 2019 Share Posted November 19, 2019 hi folks, I am having the same issue, ipv4 not set, when I loook into the config folder, what file am I to look for, is it the network.cfg as below # Generated settings: IFNAME[0]="" DHCP_KEEPRESOLV="no" DHCP6_KEEPRESOLV="no" BONDNICS[0]="eth0 eth1 eth2 eth3" BONDING_MODE[0]="1" BONDING_MIIMON[0]="100" BRNICS[0]="bond0" BRSTP[0]="0" BRFD[0]="0" USE_DHCP[0]="yes" IFNAME[1]="eth3" PROTOCOL[1]="ipv4" USE_DHCP[1]="no" IPADDR[1]="19*.***.***.***" NETMASK[1]="255.255.255.0" GATEWAY[1]="192.168.123.123" MTU[1]="9000" SYSNICS="2" Quote Link to comment
trurl Posted November 19, 2019 Share Posted November 19, 2019 7 hours ago, Dudedawg said: hi folks, I am having the same issue, ipv4 not set, when I loook into the config folder, what file am I to look for, is it the network.cfg as below # Generated settings: IFNAME[0]="" DHCP_KEEPRESOLV="no" DHCP6_KEEPRESOLV="no" BONDNICS[0]="eth0 eth1 eth2 eth3" BONDING_MODE[0]="1" BONDING_MIIMON[0]="100" BRNICS[0]="bond0" BRSTP[0]="0" BRFD[0]="0" USE_DHCP[0]="yes" IFNAME[1]="eth3" PROTOCOL[1]="ipv4" USE_DHCP[1]="no" IPADDR[1]="19*.***.***.***" NETMASK[1]="255.255.255.0" GATEWAY[1]="192.168.123.123" MTU[1]="9000" SYSNICS="2" That is pretty far away from the default network.cfg. Try renaming it and reboot so the default can be regenerated, then go from there. Quote Link to comment
Dudedawg Posted November 21, 2019 Share Posted November 21, 2019 On 11/19/2019 at 9:05 AM, trurl said: That is pretty far away from the default network.cfg. Try renaming it and reboot so the default can be regenerated, then go from there. thank you so much, it worked like a charm Quote Link to comment
IMI4tth3w Posted March 8, 2020 Share Posted March 8, 2020 Just upgraded from 6.8.0 nvidia to 6.8.2 nvidia. It seems this update changed my network settings and re-enabled bonding (which i am not using) turning off bonding in the network settings for eth0 fixed my issue. Hope this helps. Anyone know why this might have happened? Quote Link to comment
trurl Posted March 8, 2020 Share Posted March 8, 2020 3 hours ago, IMI4tth3w said: Anyone know why this might have happened? If it can't read config/network.cfg on Flash it will give you default settings. Quote Link to comment
kenny_pacheco Posted July 19, 2020 Share Posted July 19, 2020 I'm having the same issue.... Could someone provide assistance? I've tried the steps in the earlier posts (deleting config file, turning off bonding, etc). pandora-diagnostics-20200719-0507.zip Quote Link to comment
JorgeB Posted July 19, 2020 Share Posted July 19, 2020 3 hours ago, kenny_pacheco said: I'm having the same issue. No link on the NIC: Link detected: no Quote Link to comment
lucidnx Posted January 26, 2022 Share Posted January 26, 2022 I got same issue, br0 not getting IP after boot, but not always. maybe some timeout is stopping us from getting IP? Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.